ページ1に含まれる内容の要旨
H7185
Swing Swing
(Seat moves
front to back)
Cradle Cradle
(Seat moves
side to side)
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
www.fi sher-price.co.uk
ページ2に含まれる内容の要旨
Consumer Information � Please read these instructions before use of this swing. � Adult assembly is required. � Tools needed for assembly: Allen Wrench (included) and WARNING Phillips Screwdriver (not included). � Requires four LR20 (“D”) alkaline batteries for operation (not included). To prevent serious injury and/or � Maximum Weight Limit: 9 kg (20 lbs). falls and being strangled in the IMPORTANT! If your child weighs less than 9 kg (20 lbs), but is really active and appears to be able
ページ3に含まれる内容の要旨
Parts Motorized Frame Allen Wrench Fabric Panel Tray 4 Toys (toys may be different) Pad with Headrest Lower Seat Tube 2 Upper Legs Seat with Restraint System 2 Lower Legs 2 Feet Note: Tighten the screws with the enclosed Allen wrench. #8 x 1,3 cm Screw - 2 M5 x 30 mm Bolt - 2 M5 Lock Nut - 2 ALL SHOWN ACTUAL SIZE 3
ページ4に含まれる内容の要旨
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Button Holes Up Foot Lower Leg Upper Legs 3 1 � Position the fabric panel with the button holes up. � Position a lower leg so that it stands on a flat surface, as shown. � Position the legs so that the feet are away from you. � Fit a foot
ページ5に含まれる内容の要旨
Assembly Ruffle Motorized Frame L Seat Slot Tube R Elbow Foot Button Crotch Belt Hole 5 Red Dot � Locate the R and L on the underside of each elbow foot. 7 The R indicates the right leg. The L indicates the left leg. � While pressing the upper button on the right leg, fit it into the tube in the motorized frame. Make sure the upper � Position the seat upright. button on the right leg “snaps” into the hole in the tube. � Place the pad onto the seat with the ruffle toward the top � Repeat t
ページ6に含まれる内容の要旨
Assembly Waist Seat Belts Tray Pad Slot Slots 11 � Insert the tray tabs into the slots in each side of the seat. 9 � Turn the seat upright. � Fold the top of the pad down. Insert the waist belts through Lower Seat Tube the slots in the pad. Make sure the waist belts are not twisted. Short Tube 12 � Fit the lower seat tube into the short tube on the seat back. 10 � Fit the pad edges around the rim of the seat. � Hook the two fastener straps on each side of the pad onto the rim on each side
ページ7に含まれる内容の要旨
Assembly Rounded Rounded Side Side 13 � First, fit an M5 lock nut into an opening in the short tube. 15 Make sure the rounded side of the lock nut faces out. � Next, insert an M5 x 30 mm screw through the opening in the opposite side of the short tube. Fully tighten the screw with � First, fit an M5 lock nut into an opening in the upper seat tube. the Allen wrench. Make sure the rounded side of the lock nut faces out. � Next, insert an M5 x 30 mm screw through the opening in the opposite sid
ページ8に含まれる内容の要旨
Battery Installation Battery Safety Information In exceptional circumstances, batteries may leak fluids that Hint: If the swinging motion becomes noticeably can cause a chemical burn injury or ruin your product. slower, or sounds and lights become faint or stop, To avoid battery leakage: remove the batteries and replace them with four, new � Do not mix old and new batteries or batteries of different LR20 (“D”) alkaline batteries. Dispose of exhausted types: alkaline, standard (carbon-zinc)
ページ9に含まれる内容の要旨
Set Up WARNING To prevent serious injury and/or falls and being strangled in the restraint system: • Always use restraint system. Never Waist Belt Waist Belt rely on the tray to restrain child. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg/20 lbs). Crotch Belt • Never leave child unattended. • It is dangerous to use this product on an elevated surface. 2 Restraint Belts � Place your child in the seat. � Pull the crotch belt up between your
ページ10に含まれる内容の要旨
Set Up PRESS Seat Tube Button Seat Tube Tray TURN Slot 6 Using the Tray � Fit the tabs on the tray into the slots in the sides of the seat. � To remove the tray, pull one edge of the tray out and lift. Button Button Cradle Swing 4 You can adjust the motion of the swing: side to side or front to back. Lower Leg � Press the seat tube button to unlock the seat tube. Button � Rotate the seat tube to the desired position. Lower Leg Button Upright 7 Storage Recline � Press the buttons on the back of
ページ11に含まれる内容の要旨
Swing, Waterglobe and Mobile Use Power Dial Swing/Waterglobe/Mobile ON Waterglobe/ Mobile ON Reset Button Mobile/ Waterglobe Music/Sounds Switch Switch Volume Dial Swing To select waterglobe/mobile, slide switch to: Mobile � Turn the power dial to the ON position . The swing Lights (Waterglobe) begins swinging. Mobile and Lights (Waterglobe) � Select any of six speed settings . Mobile and Lights (Waterglobe) Off � Be sure to turn swinging OFF when not in use. To select sounds or music, s
ページ12に含まれる内容の要旨
Problems and Solutions Problem Probable Cause Solution Motor is not running; Power is not on Turn the power dial to one of six settings. no swinging Remove the batteries and replace in correct orientation, as Batteries incorrectly installed indicated inside the battery compartment. Dead batteries Replace all four batteries with four, fresh “D” alkaline batteries. Need to start swinging motion To start swinging motion, give the seat a light push. Motor is running but swinging stops afte