ページ1に含まれる内容の要旨
®
Product features may vary from the picture above.
Harley-Davidson is a registered trademark and the motorcycle sound is a trademark of H-D Michigan, Inc. used under license.
Owner’s Manual with Assembly Instructions
Please read this manual and save it with your original sales receipt.
For Model 73210
Tools needed for assembly: Phillips Screwdriver, Hammer and Safety Scissors (not included).
®
Use only with two Power Wheels 6 Volt Rechargeable Batteries with A-Style Connectors and Built-in Ther
ページ2に含まれる内容の要旨
Table of Contents A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
Warnings and Cautions B ELECTRICAL HAZARD WARNING • Batteries can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could cause ov
ページ4に含まれる内容の要旨
Parts C • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Wheel - 2 Vehicle Frame Wheel Axle - 2 Fork A
ページ5に含まれる内容の要旨
Parts Exhaust Pipe Set Left - Inner Half Right - Inner Half Right - Outer Half Left - Outer Half Front Fork Headlight - Rear Half Headlight - Front Half Seat Saddlebag - 2 Gas Tank Sound Box Battery Clamp Fork Cover 5
ページ6に含まれる内容の要旨
Parts (Inner Half) (Outer Half) Right Left Shock Set - 2 Handlebar Set Fender Tip Handgrips - 2 Left Mirror Housing Taillight Cover Mirror Lens - 2 Right Mirror Housing Mirror Clamp - 2 Taillight 6
ページ7に含まれる内容の要旨
WARNING P R E V E N T F I R E • • DUos en oo tn b l yy paa s R se da PPoo w wee rr W Whheeee l ls • N e v e r m o d i f y t h e e l e c t r i c a l O R O P E R A T E Parts Hex Bushing - 4 Axle Bushing - 2 12 Volt Charger 6 Volt Battery - 2 Round Bushing - 2 Not Shown: Label Sheet 3 #8 x /4" Screw – 63 .437 (Large Diameter) Cap Nut - 4* .354 (Small Diameter) Cap Nut - 2* 1 #8 x /2" Screw – 5 All Shown Actual Size *For your convenience, two extra .437 (large diameter) cap nuts and one extra .3
ページ8に含まれる内容の要旨
T M Parts Diagram D 37 33 34 13 3 35 20 28 36 17 5 2 4 29 24 15 16 19 11 23 18 31 14 9 10 30 12 25 14 32 4 7 21 8 29 22 6 12 1 Note: Some parts shown are assembled 30 11 on both sides of the vehicle. 26 27 1. Vehicle Frame 15 Headlight - Front Half 28. 12 Volt Charger 2. Vehicle Body 16. Headlight - Rear Half 29. .354 Cap Nut - 2 3. Seat 17. Handlebar - 2 30. .437 Cap Nut - 4 4. Wheel - 2 18. Sound Box 31. Battery Clamp 5. Gas Tank 19. Front Fork 32. Fender Tip 6. Left Footboard 20. Handgrip - 2
ページ9に含まれる内容の要旨
Battery Charging E Important Notes ELECTRICAL HAZARD • Your new batteries must be charged for at least 18 hours before you use them in your vehicle for WARNING the first time. • We recommend that you start charging your batteries before beginning assembly of your new vehicle. • Batteries can fall out and injure a child if vehicle tips over. Always use • The batteries must be upright while charging. battery clamp. • The charger is not a toy. • PREVENT FIRE • Do not short circuit the batteries.
ページ10に含まれる内容の要旨
WARNING P R E V E N T F I R E • D o n o t b y p a s s a P o w e r W h e e l • U s e o n l y a R e d P o w e r W h e e l s • N e v e r m o d i f y t h e e l e c t r ic a l O R O P E R A T E WARNING P R E V E N T F I R E • D o n o t b y p a s s a P o w e r W h e e l • U s e o n l y a R e d P o w e r W h e e l s WARNING • N e v e r m o d i f y t h e e l e c t r i c a l O R O P E R A T E P R E V E N T F I R E • • DUos en oot n lb yy paa s R se da PPoo w wee rr W Whheeeel l s • N e v e r m o d i f
ページ11に含まれる内容の要旨
Assembly F WARNING Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. 1 • Insert one #8 x / 2" screw through the hole near the end of the fender in the vehicle body and into the taillight. 3 1 • Insert two #8 x / 4" screws through the remaining holes in the vehicle b
ページ12に含まれる内容の要旨
TM Assembly 6 4 Vehicle Frame Vehicle Body Tab Left Footboard Slots 3 Tab • Insert four #8 x / 4" screws through the vehicle body and into the vehicle frame. Make sure the holes in the vehicle body and frame are aligned. • Tighten the screws using a Phillips screwdriver. Do not over-tighten. • Fit the tabs on the left footboard into the slots in the left side of the vehicle frame. Make sure both tabs are in Narrow the slots. Rectangular 5 Opening Hint: You may need to squeeze the left footboard
ページ13に含まれる内容の要旨
TM T M TM TM Assembly IMPORTANT! The screw marked with an asterisk in * step 9 illustration must go through the hole in the inner Peg half of the right exhaust pipe, the vehicle body and into 8 Right Exhaust the vehicle frame. Make sure all the holes are properly Pipe - Inner Half aligned and the screw goes through all three parts. • Tighten the screws using a Phillips screwdriver. Vehicle Do not over-tighten. Body Hole 10 Right Exhaust Pipe - Outer Half Stabilizer Wheel Vehicle Frame (Right Sid
ページ14に含まれる内容の要旨
Assembly Flat Side 12 1 14 1 Wheel Guide Guide Wheel Guide Axle Axle Bushing Guide 3 • Slide an axle bushing (flat side first) on the wheel axle. 3 4 4 15 Wheel 2 2 • Before applying labels to the wheels, wipe each wheel with a clean, dry cloth to make sure it is free of dirt and Hex oils. Make sure your hands are clean. Hex Bushing Bushing • Apply labels to both sides of each wheel as shown in the illustration. IMPORTANT! Labels 1 and 2 are designed to slightly overlap; and labels 3 and 4 are d
ページ15に含まれる内容の要旨
T M Assembly • Tighten the screws using a Phillips screwdriver. Do not over-tighten. 17 Tube • Repeat this step to assemble the other saddle bag to Side the other side of the rear fender. .437 (Large Diameter) Cap Nut 19 Steering Bushing Neck Wheel Axle Axle Back View Bushing • Slide an axle bushing (tube side first) onto the end of the wheel axle. Make sure the flat end of the axle bushing fits into the groove in the fork arm. Vehicle • Fit a .437 (large diameter) cap nut on the end of Steerin
ページ16に含まれる内容の要旨
TM Assembly 3 • Insert four #8 x / 4" screws through the front fork and into the headlight assembly. 20a • Tighten the screws with a Phillips screwdriver. Do not over-tighten. Headlight Assembly - Rear Half 22 DO NOT DO NOT INSERT INSERT SCREW SCREW HERE HERE Fork Axle Headlight Assembly - Front Half .354 (Small Diameter) Cap Nut 20b “Lens” • Place a .354 (small diameter) cap nut on a flat surface, inside up. • Fit the end of the fork axle into the cap nut. • Tap the opposite end of the fork ax
ページ17に含まれる内容の要旨
TM TM Assembly .354 (Small Diameter) 26 24 Cap Nut Front Fork Right Handlebar Left Handlebar Front Fork 2 1 Fork Axle • Slide the fork axle up into the bottom of the front fork, through the neck and steering stop, and out the top of the front fork. • Fit a .354 (small diameter) cap nut on the end of the fork axle. • Support the fork axle and tap the cap nut with a hammer to secure it on the end of the axle. • Pull on the .354 cap nut to make sure it is secure on the • Slide the right and left
ページ18に含まれる内容の要旨
Assembly • Push firmly to slide the shock onto the handlebar Arrow making sure that the tab on the inner shock half fits into Front the groove in the fender. 27 Fender • Repeat this procedure to slide the remaining shock on the other handlebar. Round Wheel Bushing 29 Axle Handlebar .437 (Large Diameter) Handlebar Cap Nut Tabs Tabs Shock Barrel Side Front Fork • Position the vehicle upside down. Round Bushing • Note the arrow on the underside of the front fender. • Being careful to keep the shock
ページ19に含まれる内容の要旨
Assembly Round Battery Bushing Wheel Compartment 31 33 Axle Door Battery Compartment .437 (Large Diameter) Cap Nut Ring Side Sound Box Shock 1.5V x 3 Round Bushing “AA” (LR6) • Fit a round bushing, ring side first, between the wheel and the shock. SHOWN ACTUAL SIZE Hint: You may need to push the shock outward slightly to fit the round bushing. • Loosen the screw in the sound box battery compartment • Continue to slide the wheel axle through the round door using a Phillips screwdriver and open th
ページ20に含まれる内容の要旨
Assembly Hint: To replace the batteries in the sound box, simply remove the screws from the gas tank and remove the gas tank from the vehicle frame. After replacing the batteries, 34 be sure to replace the sound box, gas tank and screws. Buttons Gas Tank Sound Box 36 PUSH HERE Tabs Tab Vehicle Body Seat Gas Tank Tab Slot Vehicle Frame • Balance the sound box on the vehicle body. (The speaker should face down.) • Fit the tabs at the bottom of the gas tank under the front end of the vehicle body.
