ページ1に含まれる内容の要旨
L3891
IMPORTANT!
KEEP INSTRUCTIONS
FOR FUTUREREFERENCE.
www.fisher-price.com.au
ページ2に含まれる内容の要旨
Consumer Information IMPORTANT! Place the high chair on a level, stable surface away from electrical flexes. Be sure to keep electrical flexes out of child's reach. WARNING • Please read these instructions before assembly and use of this product. • Adult assembly is required. Tool needed for assembly: Prevent serious injury or death from falls Phillips screwdriver (not included). or sliding out: • Weight limit: 22,7 kg (50 lbs). • Always use the restraint system for the • P rodu
ページ3に含まれる内容の要旨
Parts Pad Seat Back Frames Seat Bottom Back Base Front Base Hinge Rod Seat Bottom Tubes Footrest Food Tray Base Tray Teether Toy Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. #10 x , cm Black Screws - 7 #8 x 1,9 cm Screws - 8 Shown Actual Size 3
ページ4に含まれる内容の要旨
Assembly IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Footrest Seat Bottom 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest to the seat bottom, as shown. Plastic Rings 3 • Align the holes in the plastic rings and the seat bottom tubes. Sea
ページ5に含まれる内容の要旨
Assembly Insert Screws Here Hinge Hinge Rod 6 • Insert two #10 x 2,2 cm black screws through the footrest and into the seat bottom. Tighten the screws. • Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten the screw. • Set the seat assembly aside for Assembly step 10. Seat Back Pins Frame Leg Slot Slot 7 • Pull the frame leg out on each frame to open. Make su
ページ6に含まれる内容の要旨
Assembly Frame Decorated Side 4 Seat Height Adjusters Frame Back Legs Position Press Lever Back Base 9 Screw Retainers • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. Seat Assembly 8 • Position a frame so that the decorated side is outward. • Insert the back frame legs into the back base. • Fit a screw retainer over a hole in the back base, as shown. • Insert a #10 x 2,2 cm black screw through the screw Sockets retai
ページ7に含まれる内容の要旨
Assembly Seat Height Adjusters Screw Retainers Front Base Seat Bottom Tube Ends 11 13 • Fit the frame front legs onto the front base. • From the back and bottom of the assembly, insert a #8 x 1,9 cm screw through both seat height adjusters and the ends of • Fit a screw retainer over the hole in a front leg. the seat bottom tube. Tighten the screws. This may require • Insert a #10 x 2,2 cm black screw through the screw extra force. retainer and front leg. Tighten the screw. • Repeat this p
ページ8に含まれる内容の要旨
Assembly Shoulder Straps Crotch Strap 16 1 • Fit the pocket on the top of the pad onto the seat back. • Remove both shoulder straps from the seat back. • Remove the crotch strap from the seat back. 8
ページ9に含まれる内容の要旨
Assembly Shoulder Straps up Clips Lowest Slot Crotch Strap Down 17 19 • Fit the clips on the front edge of the pad onto the Hint: Do not unbuckle the restraint system. It is easier to seat bottom. attach or re-attach it to the product if it is buckled. • Grasp the restraint system so that the shoulder straps are up and the crotch strap is down. • Insert the end of the crotch strap through the lowest slot in the pad and the seat back. • From behind the product, attach the end of the cro
ページ10に含まれる内容の要旨
Assembly 1 Smaller Baby Larger Baby • Insert the ends of • From the front of the shoulder straps the product, insert through the lower slots in the pad. the ends of the shoulder • From behind the product, attach the ends of the shoulder straps through the upper slots in the pad and seat back. straps to the peg. • From behind the product, attach the ends of the shoulder straps to the peg. 10
ページ11に含まれる内容の要旨
Secure Child Adjuster WARNING Prevent serious injury or death from falls Shoulder Strap or sliding out: Always use the restraint system for the upright and reclined positions Free End of the seat. Adjust restraint to fit your child snugly. The tray is not designed to hold the child in the chair. Anchored End Waist/Shoulder Belt Waist/Shoulder Belt TIGHTEN • To tighten the waist straps: Feed the anchored end of the waist strap up through the buckle to form a
ページ12に含まれる内容の要旨
Secure Child Shoulder Straps Shoulder Straps • You can remove the shoulder straps and use only the waist restraint. PuSH PuSH • From behind the product, squeeze the PuSH PuSH restraint release tabs and remove the shoulder straps. • From the front of the product, pull to To change strap slots: remove the shoulder • From behind the straps from the seat product, squeeze the back/pad. restraint release tabs • Push to remove the and remove the shoulder straps from
ページ13に含まれる内容の要旨
using the Trays WARNING Prevent serious injury or death from falls or sliding out: Always use the restraint system for the upright and reclined PuLL PuLL positions of the seat. Adjust restraint to fit your child snugly. The tray is not designed to hold the child in the chair. PuSH 7 • You can adjust the base tray forward or backward. - While pulling the latches underneath the tray out, Tray adjust the base tray forward or backward . - While pushing the
ページ14に含まれる内容の要旨
using the Trays using the Brakes WARNING Food Tray Prevent serious injury or death from falls Base Tray or sliding out: • Position the high chair away from steps, hot surfaces, electrical cords and other 9 items that may cause injury to the child. • Always leave wheels locked. • Fit the food tray into the base tray, as shown. Hint: Before use, thorougly wash all parts (the trays) that may contact food. The food tray is not microwave safe. Toy Lift Tab Press Tab 11
ページ15に含まれる内容の要旨
Adjusting the Seat WARNING Prevent serious injury or death from falls or sliding out: Seat Height Adjuster • Always use the restraint system for the upright and reclined positions of the seat. Adjust restraint to fit your child snugly. The tray is not designed to hold the child in the chair. • It is recommended that only children Press Lever capable of sitting upright unassisted use the upright position of the high chair. 4 upright 13 S
ページ16に含まれる内容の要旨
Storage Care • The pad, frame, and base tray may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. • The restraint system may be wiped clean or is machine washable. Machine wash in cold water on the gentle Pull Frame cycle. Do not use bleach. Line dry. Release Latch • The food tray, teether toy and restraint system are also top rack dishwasher safe (or use bottom rack - without using the drying cycle). To remove the pad: • Remove the elastic loops from
