ページ1に含まれる内容の要旨
Product features and decorations may vary from photo above.
Instructions
Model Number: H4790
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE.
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
www.fisher-price.com
1
ページ2に含まれる内容の要旨
Warning and Caution WARNING Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • Always keep child in view while in the high chair. • Never leave child unattended. • It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. CAUTION This product contains small parts in its unassembl
ページ3に含まれる内容の要旨
Parts Pad 2 Toys (Toys may be different) 3 Food Trays Headrest Seat Back Hinge Rod Base Tray #10 x 2.2 cm Black Screw Frame Frame 2 Seat Bottom Tubes Seat Bottom #8 x 1.9 cm Screws 4 Screw Retainers #8 x 1.9 cm Screws #10 x 2.2 cm Black Screw Back Base Footrest Basket Storage Caddy Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. Front Base #8 x 1.9 cm Screw - 8 #10 x 2.2 cm Black Screw - 7 Shown Actual Size #10 x 2.2 cm Black Screw 3 3
ページ4に含まれる内容の要旨
Assembly IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use Plastic Rings if any parts are missing or broken. Contact Mattel for replace- ment parts and instructions if needed. Never substitute parts. Seat Bottom Tubes Footrest Seat Bottom 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest on the seat bottom, as shown. Plastic Rings Plastic Rings 3 #8 x 1.9 cm Screw - 4 • Align the hole
ページ5に含まれる内容の要旨
Assembly Footrest Insert Screws Here Hinge Hinge Rod 4 6 #10 x 2.2 cm Black Screw - 2 #10 x 2.2 cm Black Screw • Insert two #10 x 2.2 cm black screws through the footrest and • Turn the seat assembly face down. into the seat bottom. Tighten the screws. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2.2 cm black screw into the hinge rod. Tighten the screw. Seat Back Pin Seat Back Pin • Set the seat assembly aside for Assembly step 9. Frame Le
ページ6に含まれる内容の要旨
Assembly Seat Height Adjusters Back Base Position 4 Tapered Leg Tube Press Lever 8 Front Base 10 • Identify the back and front base. The front base has tapered leg tubes. You will use the back base for the next assembly step. • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. Frame Decorated Side Seat Assembly #10 x 2.2 cm Black Screw - 2 Frame Back Legs Sockets Screw Retainer - 2 Back Base Hole Screw Retainers Seat Bottom Tubes 1
ページ7に含まれる内容の要旨
Assembly #10 x 2.2 cm Black Screw - 2 Screw Retainer - 2 Push Seat Push Seat Height Height Adjuster Adjuster Front Leg Holes Screw Retainers Seat Bottom Tube Ends 12 13 #8 x 1.9 cm Screw - 2 • Insert the frame front legs onto the front base. • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Fit a screw retainer over a hole in the front leg. 7 • Insert a #8 x 1.9 cm screw through each seat height adjuster • Insert a #10 x /8" (2.2 cm) black screw thro
ページ8に含まれる内容の要旨
Assembly Pad Seat Height Adjusters #8 x 1.9 cm Screw - 2 Elastic Loops Hole Hole Front View Seat Bottom Tube Ends Back and Bottom View 14 Tabs • From the back and bottom of the assembly, insert a #8 x 1.9 cm screw through both seat height adjusters and the ends of the seat bottom tube. Tighten the screws. Elastic Loops 15 Back and Bottom View • Lift the assembly upright. • From the front of the assembly, place the pad onto the seat. • Lift the bottom of the pad. Insert the two elastic loops on t
ページ9に含まれる内容の要旨
Assembly Upper Shoulder Belt Slots Shoulder Portion Lower Shoulder Belt Slots Headrest Pad Slots Slot Crotch Belt 16 Shoulder Portion • Insert the crotch belt through the slot in the pad. Make sure 18 the crotch belt is not twisted. • Fold the top of the pad down. • Fit the top of the pad over the seat back. • Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back. • Fold the bottom edge of the pad under the edge of the seat bottom to f
ページ10に含まれる内容の要旨
Assembly Frame Tab Handle Pad Strap Storage Caddy Headrest Strap Small Fastener 21 Large Fastener • Fit the storage caddy onto either frame tab. 19 Back View • Fit the strap on the top of the headrest through the handle. • Fit the pad strap through the handle and press it to the small fastener on the back of the seat. Basket • Fit the headrest strap through the handle and press it to the large fastener on the back of the seat. Elastic Loop Elastic Loop Tab 22 Tab • Fit the basket onto the othe
ページ11に含まれる内容の要旨
B A A Securing Your Child IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replace- ment parts and instructions if needed. Never substitute parts. Anchored End Place the high chair on a level, stable surface away from electri- Buckle cal flexes. Be sure to keep electrical flexes out of child’s reach. B WARNING Free End Prevent serious injury or death from falls or
ページ12に含まれる内容の要旨
Securing Your Child Hold Adjuster Shoulder Portion Pull Strap Down Slide Adjuster Down 6 • From the front of the high chair, pull the shoulder portion of the waist/shoulder belts out and then fit them back through the desired shoulder belt slots in the headrest pad, seat pad and the seat back. Pull on the belts to be sure they are secure in the 4 Tighten Loosen seat back. • To tighten the shoulder belts: Hold the adjuster and pull the front shoulder strap down. • To loosen the shoulder belts: Sl
ページ13に含まれる内容の要旨
Using the Trays and Toys WARNING Base Tray Prevent serious injury or death from falls or sliding out. The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. Release Bar 8 Hint: The base tray can be adjusted for your child’s comfort two ways (see steps 8 and 9)! • While pushing the release bar on the front of the base tray, adjust the base tray forward or backward. Base Tray Armrest Squeeze Latch Base Tray 9 • Wh
ページ14に含まれる内容の要旨
Using the Trays and Toys Food Tray Squeeze Latch Base Tray Base Tray 10 12 Hint: The base tray can be removed two ways (see steps 10 and 11)! • Fit the food tray into the base tray, as shown. • Squeeze one or both of the latches underneath the base tray Hint: Before use, thorougly wash all parts (the trays) that may contact food. and lift. Toy Base Tray Tab Release Bar Slot Tab 11 13 • While pushing the release bar on the front of the base tray, pull the tray base towards you and remove. • Inser
ページ15に含まれる内容の要旨
Adjusting the Seat Upright WARNING Semi-Recline Prevent serious injury or death from falls or sliding out. It is recommended that the high chair be used in the upright position only by children capable of sitting Recline upright unassisted. Seat Height Adjuster Squeeze Back View Press Lever 15 4 Hint: Adjust the seat angle to any of three positions: Upright, Semi- Recline or Recline. 14 To adjust the seat angle: • Squeeze the seat back handle and push the seat back forward Hint: Adjust the seat
ページ16に含まれる内容の要旨
Storage Care • The pad and headrest are machine washable. Wash them sepa- rately in cold water on the gentle cycle. Do not use bleach. Line dry. • The frame and base tray may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the base tray. • The food trays and toys are dishwasher safe. Simply remove the food tray from the base tray and place in your dishwasher. To remove the pad: Base Tray • Remove the four elastic loops from the pegs on the underside and back of th
