ページ1に含まれる内容の要旨
THE PROFESSIONAL GRILL CART
Use & Care and Installation Guide
MODELS:
CAD-30
CAD-36
CAD-48
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
A MESSAGE TO OUR CUSTOMERS Thank you for selecting this DCS by Fisher & Paykel Grill Cart. Because of this product’s unique features we have developed this Use & Care and Installation Guide. It contains valuable information on how to properly install and maintain your new Professional Grill Cart for years of safe and enjoyable use. To help serve you better, please fill out and submit your Product Registration by visiting our website at www.dcsappliances.com and selecting “Customer Care” on the h
ページ4に含まれる内容の要旨
TABLE OF CONTENTS SAFETY PRACTICES & PRECAUTIONS 2 MODEL IDENTIFICATION & DIMENSIONS 3 BEFORE INSTALLING YOUR APPLIANCE Shipping Inspection 3 INSTALLATION Locating the Cart 4 Cart Assembly Instructions 4-8 Optional Attaching Side Shelf 9 Optional Attaching Sink Drain Kit 10-17 USING THE CART Removing Drawers 18 Re-installing Drawers 19 Freezer Pack (Optional) 20 CARE AND MAINTENANCE 21 SERVICE 22 WARRANTY 23-24 SAFETY PRACTICES AND PRECAUTIONS 1. Begin by insuring proper installation and servic
ページ5に含まれる内容の要旨
MODEL IDENTIFICATION & DIMENSIONS CAD-30 CAD-36 CAD-48 24” 48” 24” 30” 36” 24” 4-1/2” 4-1/2” 4-1/2” front view front view front view CAD-30/36/48 23-1/2” 32-1/8” 35-1/2” 3-3/8” 25-1/2” side view BEFORE INSTALLING YOUR APPLIANCE SHIPPING INSPECTION 1. Inspect the Cart to verify that there is no shipping damage. 2. If any damage is detected, call the retail dealer and initiate a damage claim. DCS by Fisher & Paykel is not responsible for shipping damage. NOTE: Do not discard any packing material (
ページ6に含まれる内容の要旨
INSTALLATION CART ASSEMBLY INSTRUCTIONS IMPORTANT: Read all instructions before you begin. Do not jump ahead or skip any step. CAUTION: Some parts have sharp edges; care must be taken when handling the various components to avoid injury. Please read safety information provided in these instructions before beginning assembly. Wear gloves when handling. Two or more people should work together to assemble the cart and All-Grill, Double Side Burner/Sink, or Double Side Burner/Griddle. NOTE: Avoid
ページ7に含まれる内容の要旨
INSTALLATION CART ASSEMBLY INSTRUCTIONS STEP 1 Link Carts Together (optional) (To link two or more CAD carts, the following instructions must be done first, using the hardware provided, before installing the top modules.) 1. To link your carts together - hand tighten 2 bolts, 4 washers, and 2 nuts on the front and back sides of the carts as shown in Fig. 03. Carefully wrench tighten fasteners once carts are aligned with each other. CAUTION: Once the carts are linked, they cannot be moved. Movi
ページ8に含まれる内容の要旨
INSTALLATION CART ASSEMBLY INSTRUCTIONS STEP 2 Outdoor Appliance Head Preparation 1. First you will need to remove the angle brackets from the side of the unit and replace them with cart mount brackets (Fig. 04). Unit is shipped prepared for island installation. SCREWS 2. Install the Bracket Tab on both sides using 8 of the 10-24 x 1/2” screws. Install each bracket with 4 screws on each Fig. 04 side of the grill head (Fig. 04, 05 and 06). For a CAD-48, use the appropriately labeled bracket for
ページ9に含まれる内容の要旨
INSTALLATION CART ASSEMBLY INSTRUCTIONS 3. Position tabs on side bracket to fit into slots on the cart (be aware of pinch points)(Fig. 10 -12). When complete, the landing ledge should sit flush on the top of the cart (no gap). 4. Secure the head to rear of cart (Fig. 13) with Phillips-head screws provided (10-24 x 1/2”). PINCH POINT Fig. 11 Fig. 12 Fig. 10 Fig. 13 STEP 4 Front End Screw Installation 1. Install remaining screws (10-24 x 1/2”) into the front of head to the cart (Fig.14). 2. Slide
ページ10に含まれる内容の要旨
INSTALLATION CART ASSEMBLY INSTRUCTIONS STEP 5 Gas Hookup - LP Attach LP gas line connector hose assembly (as shown in “LP Gas Hookup” section - The Professsional Liberty Collection, Use/Care Guide) and then connect to LP tank as shown. Fig. 16 Fig. 15 FOR YOUR SAFETY To prevent personal injury or damage to the drawers, do not overload them. The maximum rating of each drawer is 35 pounds. WARNING! Do not push down on the top of the drawers. The unit could tip forward. COVER HANGER Cover hanger
ページ11に含まれる内容の要旨
INSTALLATION SIDE SHELF ASSEMBLY INSTRUCTIONS (OPTIONAL) STEP 6 Optional Attach Side Shelf Accessory on Either Side NOTE: Side shelf Model CAD-SK can be installed with the head already on SHOULDER BOLT the cart. SCREW HOLES 1. Screw shoulder bolts (2) into the bottom screws on the side of the cart (Fig. 20 and 21). Tighten with 5/32 Allen wrench. 2. Slide left and right side shelf brackets over the shoulder bolt (Fig. 22) and install top screw attaching the side shelf brackets onto the cart (
ページ12に含まれる内容の要旨
INSTALLATION SINK DRAIN ASSEMBLY INSTRUCTIONS (OPTIONAL) Optional wood cutting board (model # CAD-WCB, 70861) shown in Figure 28 can be purchased as an accessory from Customer Care at (888) 936-7872. Fig. 27 Fig. 28 STEP 7 Optional Attach Sink Drain Kit Content Included: Your Sink Drain Accessory Kit is packaged in one box. The box contains the following components: Contents Qty. Contents Qty. 3-1/2” Snap Bushing 1 Gray Water Tank 1 Snap Lock Clip 1 1-1/2”Tailpiece 2 Washer Contents Qty. Fitti
ページ13に含まれる内容の要旨
INSTALLATION SINK DRAIN ASSEMBLY INSTRUCTIONS (OPTIONAL) NOTE: Remove all racks and drawers from the cart and grates. And remove burner caps and drip tray from the Side Burner/Sink prior to kit installation. 1. Attach tank bracket on the right side of the cart as shown in Fig. 29. 2. Install the snap bushing in the center divider and the snap-lock clip in the back bottom of the cart into the hole provided, as shown in Fig. 30 and 31. Note the direction of installation. 3. Attach sink drain hose
ページ14に含まれる内容の要旨
INSTALLATION SINK DRAIN ASSEMBLY INSTRUCTIONS (OPTIONAL) 4. Install the above tank/hose assembly in the cart, over the tank bracket and feed the sink drain hose through the hole in the center divider (Fig. 33). NOTE: The drain hose at the bottom of the tank exits the hole in the back of the cart (Fig. 34). 5. Attach the 1/2” ball valve and fitting to the tank drain as shown in Fig. 35, and tighten the hose clamp. Fig. 34 Fig. 33 Fitting Hose Clamp 1/2” Ball Valve Fig. 35 12
ページ15に含まれる内容の要旨
INSTALLATION SINK DRAIN ASSEMBLY INSTRUCTIONS (OPTIONAL) 6. Set the Side Burner/Sink securely on a table and attach the faucet to the sink as shown in Fig. 36. CAUTION: Finger tight first, then use a wrench. Rubber Washer Lock Washer Fig. 36 Lock Nut AIR VENT TUBE 7. Feed the 3-foot water supply hose/air vent tube through the hole at the bottom of the burner box, and attach it to the faucet (Fig. 37). CAUTION: Finger tight first, then use a wrench. Fig. 37 8. Perform the following instruction
ページ16に含まれる内容の要旨
INSTALLATION SINK DRAIN ASSEMBLY INSTRUCTIONS (OPTIONAL) WARNING! Fig. 39 Beware of pinch points and sharp edges to avoid injury to arms and hands. B. Install the bracket tab on both sides of the appliance head using 8 of the 10-24 x 1/2” screws. SCREWS Install each bracket with 4 screws on each side of the outdoor appliance head (Fig. 39 and 40). Fig. 40 9. Place head onto cart (2 persons required) A. Remove drip tray/pan (Fig. 41) and other removable components (to lighten the load) such as gr
ページ17に含まれる内容の要旨
INSTALLATION SINK DRAIN ASSEMBLY INSTRUCTIONS (OPTIONAL) C. Position tabs on side bracket to fit into slots on the cart (be aware of pinch points)(Fig. 44-45). When complete, the landing ledge should sit flush on the top of the cart (no gap)(Fig. 46). D. Secure the head to rear of cart (Fig. 47) with (2) Phillips-head screws provided (10-24 x 1/2”). E. Install remaining (3) screws (10-24 x 1/2”) into the front of head to the cart (Fig. 48). Fig. 44 PINCH POINT Fig. 46 Fig. 45 Fig. 47 Fig. 48 15
ページ18に含まれる内容の要旨
INSTALLATION SINK DRAIN ASSEMBLY INSTRUCTIONS (OPTIONAL) 10. Feed the water supply hose through the center divider hole, down to the bottom opening of the cart (Fig. 49). Place the end of the water supply hose in the snap-lock clip and lock it in place (Fig. 50) 11. Attach the water hose adapter to the water supply hose. (Fig. 51). NOTE: Make sure you have the supply connection in accordance with local codes. 12. Feed the air vent tube over the center divider and attach it to the brass fitting
ページ19に含まれる内容の要旨
INSTALLATION SINK DRAIN ASSEMBLY INSTRUCTIONS (OPTIONAL) 13. Attach the sink drain hose to the bottom of the sink (use one tailpiece washer) (Fig. 54 and 55). 14. Push the sink drain hose up and over the edge of the side panel (Fig. 56). This will prevent the interference between this hose and the top rack. It also creates proper drainage from the sink to the water tank. And/or use the cable tie provided to hold the hose up (Fig. 57). 15. Slide drip tray/pan back into place and reinstall parts r
ページ20に含まれる内容の要旨
USING THE CART REMOVING DRAWERS 1. To remove the drawers, pull them out until their slider latch is visible. Carefully push the latch down on the left side while pulling up on the latch on the right side and pull the drawer completely out of the frame (Fig. 58 and 59). 2. To prevent damage to surfaces, place the drawers on a stable surface on a protective towel or tablecloth while removed from the cart. Slider latch Slider latch Slider latch Fig. 58 Fig. 59 FOR YOUR SAFETY To prevent personal
