ページ1に含まれる内容の要旨
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
Installation/Care/Use Manual
™ ®
Soft Sides Fountains with FLEXI-GUARD
EDFP217C EDFP217RAC
Installer
To assure you install this model easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH
PLUMBING , ELECTRICAL AND OTHER APPLICABLE CODES. After installation, leave
these instructions inside the fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFO
ページ2に含まれる内容の要旨
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC EDFP217C FIG. 3 LEGEND A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED D = 1-1/4" TRAP FURNISHED COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM E = 3/8" (10mm) DIA. HOLES FOR SECURING WALL SHUT OFF BY OTHERS FOUNTAIN TO WALL B = RECOMMENDED LOCATION FOR WASTE OUTLET
ページ3に含まれる内容の要旨
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC EDFP217RAC FIG. 4 LEGEND A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED D = 1-1/4" TRAP FURNISHED COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM E = 3/8" (10mm) DIA. HOLES FOR SECURING WALL SHUT OFF BY OTHERS FOUNTAIN TO WALL B = RECOMMENDED LOCATION FOR WASTE OUTLET
ページ4に含まれる内容の要旨
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC EDFP217C W/MOUNTING PLATE FIG. 5 LEGEND NOTE: A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED REFERENCE SEPARATE INSTALLATION COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM INSTRUCTIONS. FOR DETAILS ON MP20 WALL SHUT OFF BY OTHERS SURFACE MOUNTING PLATE. B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN STUBBED 1-1/2" (35mm) FROM THE WALL C = RECOMMENDED LOCATION FO
ページ5に含まれる内容の要旨
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC EDFP217RAC W/MOUNTING PLATE FIG.6 NOTE: LEGEND REFERENCE SEPARATE INSTALLATION A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED INSTRUCTIONS. FOR DETAILS ON MP20RA COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM SURFACE MOUNTING PLATE. WALL SHUT OFF BY OTHERS B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN STUBBED 1-1/2" (35mm) FROM THE WALL C = RECOMMENDED LOCATION
ページ6に含まれる内容の要旨
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC INSTALLATION INSTRUCTIONS 1. Wall should already be framed for the fountain using the positioning dimensions shown in Figures 3, 4, 5, or 6. Shown dimensions pertain to installation location (framing must support up to 300 lbs. weight). These dimensions are required for compliance with ANSI Standard A117.0. 2. Install rough-in plumbing as shown in Figures 3, 4, 5, or 6. Waste line should extend a minimum of 2"
ページ7に含まれる内容の要旨
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC FIG. 7 FIG. 8 21 7 6 8 19 20 9 NOTE: WHEN INSTALLING REPLACEMENT BUBBLER AND PEDESTAL, TIGHTEN NUT (ITEM 9 OR 20) ONLY TO HOLD PARTS SNUG IN POSITION. DO NOT OVER TIGHTEN. 16 23 FIG. 9 Installing back panel: When installing back panel (item 16) without mounting plate accessory MP20 or MP20RA, attach (4) channel braces (item 23) as shown in FIG. 9. Remove the protective backing from the tape installed on the brace. Line up
ページ8に含まれる内容の要旨
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC PARTS LIST FIG. 10 ITEM NO. P ART NO. DESCRIPTION 1 LK464 DRAIN 2 15005C RETAINING NUT 3 45662C PUSH BUTTON 4 45663C PUSH BUTTON SLEEVE 16 5 50986C REGULATOR HOLDER 6 A54874 ORIFICE ASSY SEE FIG. 7 OR 8 7 56011C HOUSING ASSY 8 55997C PEDESTAL 9 75580C BUBBLER LOCKNUT 10 61313C REGULATOR 11 75672C CAP SCREW 14 12 112627543890 SCREW - #10-24 X .50 PHTC 13 55996C STRAINER 22 14 28782C FOUNTAIN ARM - SHORT 28783C FOUNTAIN ARM - LONG 27959C FO
