ページ1に含まれる内容の要旨
INDOOR/OUTDOOR PRODUCTS
KEROSENE PORTABLE
FORCED AIR HEATERS
“USER’S MANUAL AND
OPERATING INSTRUCTIONS”
COMPLIES WITH
ANSI A10.10-1998
CAN/CSA/B140.0-03 AND CSA
B140.8-1967
MODEL : KFA400DGD
Before the first use of this heater, please read this USER’S MANUAL very
carefully. This USER’S MANUAL has been designed to instruct you as to
the proper manner in which to assemble, maintain, store, and most
importantly, how to operate the heater in a safe and efficient manner.
Please keep this manual for
ページ2に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! DANGER: IMPROPER USE OF THIS HEATER CAN RESULT IN SERIOUS INJURY OR DEATH FROM BURNS, FIRE, EXPLOSION, ELECTRICAL SHOCK AND/OR CARBON MONOXIDE POISONING. WARNINGS: 1. RISK OF INDOOR AIR POLLUTION! • Use this heater only in well ventilated areas. Provide at least a three-square foot (2,800 sq. cm.) opening of fresh outside air for each 100,000 BTU/hr. of heater rating. • People with breathing problems should consult a physician before using the
ページ3に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! CONTENTS OF USER’S MANUAL ITEM PAGE # PRECAUTIONS - SAFETY GUIDE 1 1. INTRODUCTION 2 2. FEATURES 2 3. UNPACKING AND ASSEMBLY 3 4. KEROSENE (1-K OR NO. 1 FUEL OIL) 4 5. OVERVIEW OF HEATER DESIGN 5 6. FUELING YOUR HEATER 5 7. OPERATION 6 8. LONG TERM STORAGE OF YOUR HEATER 8 9. MAINTENANCE 9 10 REPLACING FUSE 14 11 TROUBLE SHOOTING GUIDE 15 12 WIRING DIAGRAM 16 13 SPECIFICATIONS 17 14 EXPLODED PARTS DRAWING 18 15 PARTS LIST 19 1. INTRODUCTION Please
ページ4に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 3. UNPACKING AND ASSEMBLY 1. REMOVE THE HEATER AND ALL PACKING MATERIALS FROM THE BOX. (See Fig.2) NOTE: Save the shipping carton and packing materials for future storage. Screw(L) Screw(S) Nuts Wheels Cord Wrap Cap Nuts(L) Bushings Cap Nuts(S) Washers Hardware Kit Part No : HW-KFA1019 Handle Handle Wheel Support Frame Threaded Axle Figure 2. PACKING MATERIALS 2. ASSEMBLING Tools Required Medium Phillips Screwdriver 24 Socket Wrench Assembling
ページ5に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! Screw(L) Handle Screw(S) Cap Nut(S) Cord Wrap Screw(S) Fuel Tank Flange Wheel Support Frame Wheel Air Inlet Nut Washer Threaded Axle Cap Nut(L) Bushing Figure 3. Assembling Handle & Wheel and Cord wrap 4. KEROSENE (1-K) For optimal performance of this heater, it is strongly suggested that 1-K kerosene be used. 1-K kerosene has been refined to virtually eliminate contaminants, such as sulpher. Which can cause a rotten egg odor during the operation
ページ6に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 5. OVERVIEW OF HEATERS DESIGN Fuel System: This heater is equipped with a Fuel pump(Gear)that pulls fuel through the fuel line connected to the fuel tank and then pushes fuel through a filter and a solenoid valve and out the burner head nozzle. This fuel is sprayed into the combustion chamber in a fine mist. “Sure Fire Ignition”: The electronic ignitor sends voltage to a specially designed spark plug. The spark plug ignites the fuel and air mi
ページ7に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 7. OPERATION A.) VENTILATION RISK OF INDOOR AIR POLLUTION/USE HEATER ONLY IN WELL VENTILATED AREAS. Provide at least a three-square foot(2,800 sq. cm.) opening of fresh outside air for each 100,000 BTU/hr. of heater rating. B.) OPERATION TO START HEATER 1. Fill fuel tank with kerosene or No. 1 fuel oil. 2. Attach fuel cap. 3. Plug power cord of heater into three-prong, grounded extension cord. Extension cord must be at least six feet long. E
ページ8に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! TO STOP HEATER CAUTION ; Never unplug heater while heater is running Heater must go through cooling cycle. The cooling cycle cools the combustion chamber. Damage to heater can occur if combustion chamber is not cooled. Do not restart heater until cooling cycle is complete. 1. Turn operating switch to “OFF”. This will cause heater flame to go out. The motor will continue to run during the cooling cycle. (Room Temp. Display will show “CC” during th
ページ9に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 8. LONG TERM STORAGE OF YOUR HEATER 1. Remove fuel drain bolt from rear bottom side of fuel tank using 3/4” socket or adjustable wrench and drain. 2. Using a small amount of kerosene, swirl and rinse the inside of the tank. NEVER mix water with the kerosene as it will cause rust inside the tank. Pour the kerosene out making sure that you remove it all. IMPORTANT : Do not store kerosene over summer months for use during next heating season. Using
ページ10に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 9. MAINTENANCE WARNING!! NEVER SERVICE HEATER WHILE IT IS PLUGGED IN OR WHILE HOT! USE ORIGINAL EQUIPMENT REPLACEMENT PARTS. Use of third party or other alternate components will void warranty and may cause unsafe operating conditions. A.) UPPER SHELL REMOVAL Screw Shell Upper -Remove screws along each side and top of heater using medium phillips screw driver. -Lift upper shell off. (See Figure 7) Figure 7. Upper Shell Removal B.) FAN BLADES A
ページ11に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! C.) SPARK PLUG SPARK PLUG CLEAN AND REGAP EVERY 600 HOURS BURNER HEAD OPERATION OR REPLACE AS NEEDED. - Remove upper shell (See page 9). SPARK PLUG WIRE - Remove spark plug wire from spark plug (See Figure 9) - Remove spark plug from burner head using medium phillips screw driver. - Clean and regap spark plug electrodes to 0.14”(3.5mm) gap. - Reinstall spark plug in burner head. - Attach spark plug wire to spark plug. - Reinstall upper shell. D.
ページ12に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! E.) PHOTOCELL CLEAN PHOTO CELL ANNUALLY OR AS NEEDED. - Remove upper shell(See Page 9) - Remove photocell from photocell Bracket and disconnect photocell from connector. - Clean photocell lens with cotton swab. - Inspect photcell lens for damage. If damaged, replace photocell. PHOTOCELL BRACKET PHOTOCELL CONNECTOR PHOTOCELL LENS INSTALL PHOTOCELL 1)INCORRECT 2)CORRECT Figure 11. Clean photocell Lens F.) FUEL LINES TIGHTENING FUEL LINES ANNUALLY
ページ13に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! G.) FUEL FILTER CLEAN TWICE PER HEATING SEASON OR AS NEEDED. Tank Fuel Filter - Remove fan guard (See Figure 11). SCREW PUMP - Disconnect fuel line (B) from pumpand pump fuel filter assembly with3/8” wrench (See Figure 14). - Remove two screws that fix bracket-filter to shell lower and remove bracket-filter. - Carefully pry fuel filter loose from fueltank with flat end of screwdriver. - Wash fuel lines and fuel filter with clean SHELL LOWER B
ページ14に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! H.) PUMP PRESSURE ADJUSTIMENT - Remove pressure gauge plug from pump with 1/8” allen wrench. - Install accessory pressure gauge to pressure gauge port. (See Figure 16) - Start heater (See operation, page 6) Allow motor to reach full speed. - Adjust pressure. (Using a small flat blade screw driver) Turn pressure adj. Screw to clock wise to increase pressure. Turn screw to counter clock wise to decrease pressure. Set pump pressure to 125 PSI. - Sto
ページ15に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 10. REPLACING FUSE NOTICE : This heater is fuse protected. If your heater fails to ignite, DO NOT RETURN YOUR HEATER TO THE STORE. Please follow the simple instruction below to inspect and change the fuse. PROCEDURE FOR REPLACING FUSE WARNING : SHOCK HAZARD To prevent personal injury, unplug the power cord before replacing fuse. 1. Unplug heater. 2. Turn Fuse Cover COUNTERCLOCKWISE 45° using a flat blade screwdriver and remove Fuse from Fuse
ページ16に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 11. TROUBLE SHOOTING GUIDE TROUBLE POSSIBLE CAUSE CORRECTIVE ACTION 1. Wrong pump pressure 1. See Pump Pressure Adjustment, Heater ignites but MAIN PCB page 13. assembly shuts heater off after 2. Dirty Fuel Filter a short period of time. 3. Dirt in Nozzle 2. See Fuel Filter, page 12. (Indicator lamp is flickering and 4. Dirty Photocell Lens 3. See Nozzle, page 10. room temp. display indicates “E1”) 5. Photocell Assembly not 4. Clean Photocell Len
ページ17に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 12. WIRING DIAGRAM CONTROL PCB LIMIT CONTROL BLACK SOL. CN7 BLACK BLACK VALVE POWER LAMP SPARK PLUG BLACK (LED) WHITE IGNITOR WHITE CN4 WHITE BLACK ORANGE BLACK THERMOSTAT PUMP (TEMP. CONTROL) RED CN3 RED WHITE MOTOR CAPACITOR CN2(AC2)/ WHT 45uF/400Vac CN1(AC1)/ BLK CN5 CN8 CN6 YEL WHITE BLUE WHITE BLUE YEL ROOM SENSOR OPERATING SWITCH PHOTOCELL BLACK POWER PLUG BLACK FUSE GREEN 20A/250VAC AC120V 60Hz WHITE ELECTRIC GREEN EARTH OUTLET EARTH 16 BL
ページ18に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 13. SPECIFICATIONS 32.8" 52.5" 31.4" KFA400DGD MODEL KFA400DGD BTU/Hr 400,000 Fuel Consumption-Gal./ ( ./Hr) 3.0(11.36) Fuel Tank Capacity-Gal ( ) 29.0(110.0) Pump Pressure PSI (kgf/ ) 125(8.79) Volts/Hz/Amps 120VAC/60/4.4 Phase 1 52.5” × 31.4” × 32.8” (1,334 × 798 × 834) Size(D W H), Inch( ) Weight Ibs. ( ) 150(68.0) 17
ページ19に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 14. EXPLODED PARTS DRAWING (KFA400DGD MODEL) NOTE: SPECIFY MODEL NUMBER AND PART NUMBER WHEN ORDERING PARTS. 19 48 25 19 24 47 11 46 32 26 35 29 31 27 16 22 11 28 23 16 30 23 30 19 15 19 20 19 42 1 17 6 18 5 19 44 19 43 3 34 23 33 21 19 19 8 4 36 45 37 11 38 7 19 14 13 12 2 9 39 10 40 41 18
ページ20に含まれる内容の要旨
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 15. PARTS LIST PART No. KEY No. Quantity DESCRIPTION KFA400DGD 1 Fuel Tank Assembly 2151-0025-00 1 2 Fuel Drain Bolt 4329-0072-00 1 3 Fuel Gauge 2156-0053-00 1 4 Fuel Filter 3221-0009-00 1 5 Fuel Cap 2151-0003-00 1 6 Filler Neck Assembly 2155-0007-00 1 7 Space Support 3713-0004-00 5 8 Card Support 3713-0016-00 3 9 Cord Bushing 3712-0013-00 1 10 Power Cord 3980-0087-00 1 11 Bushing Grommet(L) 3231-0121-00 3 12 Electric Outlet Assembly 39D0-0780-00
