ページ1に含まれる内容の要旨
DIRECT-VENT FIREpla CE
OWNER’S OpERa TION aND INSTalla TION MaNUal
NaTURal GaS “TUDOR” MODES (V)T32N- l a SERIES
aND CGDV32NR
RO p paNE/ G lp aS “TUDOR” MODES (V)T32 l -p a SERIES
aND CGDV32pR
WARNING: If the information in this manual is not fol-
lowed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMEL
ページ2に含まれる内容の要旨
TablE OF CONTENTS Safety Information ............................................... Cleaning and Maintenance ................................ 30 Product Identification ........................................... 4 Troubleshooting ................................................. 3 Local Codes......................................................... 4 Replacement Parts ............................................ 36 Product Features ................................................. 4 Service
ページ3に含まれる内容の要旨
SaFETy INFORMa TION Keep the appliance area clear Continued and free from combustible ma- Carbon Monoxide Poisoning: Early signs of carbon terials, gasoline and other flam- monoxide poisoning resemble the flu, with head- mable vapors and liquids. aches, dizziness or nausea. If you have these signs, the fireplace may not be working properly. Get Do not place clothing or other fresh air at once! Have fireplace serviced. Some flammable material on or near people are more affected by carbon mo
ページ4に含まれる内容の要旨
SaFET INFORM y a TION OC l al CODES Continued Install and use fireplace with care. Follow all local codes. In the absence to local codes, use the cur- 9. Do not use this fireplace to cook food or burn rent National Fuel Gas Code ANSI Z223.1/NFPA paper or other objects. 54* (USA) or the current CSA-B149.1 Installation 10. This appliance, when installed, must be electri- Code (Canada). cally grounded in accordance with local codes *Available from: or, in the absence of local codes, with the
ページ5に含まれる内容の要旨
• There must not be any obstruction such as bushes, pRE-INST alla TION garden sheds, fences, decks or utility buildings pREa p Ra TION within 24" from the front of the termination cap. LOCATION AND Sp ACE • Do not locate termination cap where excessive snow or ice build up may occur. Be sure to clear REUIREMENTS q vent termination area after snow falls to prevent Determine the safest and most efficient location accidental blockage of venting system. When for your DESA direct-vent firepla
ページ6に含まれる内容の要旨
pRE-INST alla TION pREa p Ra TION 5 3 D 1 Continued 13 B / " 9 /" 39 C /8" 8 1 A 8 / " NOTICE: This fireplace is in- tended for use as supplemental heat. Use this fireplace along with 7 E 9 /8" 3 34 / " your primary heating system. Do F 8 5 Nailing 34 G /8" Nailing Tabs not install this fireplace as your Tabs 1 primary heat source. If you have a 54 H /8" central heating system, you may Figure 5 - Framing Clearances for Corner Installation run system’s circulating blower while using fi
ページ7に含まれる内容の要旨
V G G V A E D V B L OC l a TION OF TERMINaTION Cap N N H C I B Fixed V V Fixed Closed Openable Closed Openable B F V G V J X B B M A V K X V TERMINATION CAP AIR SUPPLY INLET G GAS METER RESTRICTED AREA X (TERMINATION PROHIBITED) A = clearance above grade, veranda, porch, deck, or balcony I = clearance to service regulator vent outlet [*72 inches (182.9cm) [*12 inches (30.5mc) minimum] minimum] B = clearance to window or door that may be opened J = clearance to non-mechanical air supply inlet
ページ8に含まれる内容の要旨
VENTING INSTalla TION WARNING: Read all instruc- INSTRUCTIONS tions completely and thoroughly NOTICE: Read these instruc- before attempting installation. tions completely before at- Failure to do so could result in tempting installation. serious injury, property damage or loss of life. These models are tested and approved for use with DESA (direct-vent) pipe components and NOTICE: Failure to follow these in- terminations. structions will void the warranty. The venting system must termina
ページ9に含まれる内容の要旨
5. Carefully determine the location where the vent VENTING INSTalla TION pipe assembly will penetrate the outside wall. INSTRUCTIONS The center of the hole should line up with the Continued center-line of the horizontal vent pipe. Mark the 3 3 wall for a 10 /4" x 10 /4" square hole. Cut and INSTALLATION LANNING p frame the square hole in the exterior wall where There are two basic types of direct-vent instal- the vent will be terminated. If the wall being lation: penetrated is constructe
ページ10に含まれる内容の要旨
10. Place fireplace into position and shim with VENTING INSTalla TION noncombustible material if needed. Nail or INSTRUCTIONS screw side flanges to framing to secure unit in Continued place. IMPORTANT: Make sure fireplace is level before securing. If fireplace is not level 6. Noncombustible Exterior Wall: Position the 1 it will not work properly. horizontal vent cap in the center of the 8 /2" round hole and attach to the exterior wall with four screws (see page 10). Note: The four wood
ページ11に含まれる内容の要旨
VENTING INSTalla TION WARNING: Never run vent INSTRUCTIONS downward as this may cause Continued excessive temperatures which Siding could cause a fire. Operation of Standoff improperly installed and main- tained venting system could result in serious injury, property Minimum Pipe Screws 1 damage or loss of life. Overlap 1 /4" GROUND FLOOR INSTALLATION Wall Recommended Applications: Firestop • Installation using cabinet surrounds • Through the wall using round or square termi- nation
ページ12に含まれる内容の要旨
VENTING INSTalla TION INSTRUCTIONS Continued CORNER INSTALLATION Recommended Applications: • Corner ground floor installation • Ground floor installation where pipe vents horizontally through wall (over 12" horizontal pipe) • Basement installation where one foot clearance from ground to termination is possible Not to Exceed 90° Elbow Not to Exceed Square (H) Limits (H) Limits Termination Square As Required 90° Termination for (V), See Elbow Chart for Pipe Section Required Wall 1" Min. F
ページ13に含まれる内容の要旨
VENTING INSTalla TION INSTRUCTIONS Continued HORIZONTAL SYSTEM INSTALLATION USING TWO 90° ELBOWS The following configurations show the minimum vertical rise requirements for a horizontal system using two 90° elbows. Venting with Two 90° Elbows Horizontal (H ) + 1 Vertical (V) Horizontal (H ) Horizontal (H ) 1 2 5' min. ' max. 6' max. 6' min. 4' max. 1' max. 7' min. 6' max. 18' max. 8' min. 8' max. 0' max. 0' max. 8' max. 0' max. 45° Elbow Figure 17 - Horizontal Termination Conf
ページ14に含まれる内容の要旨
Flat Ceiling Installation VENTING INSTalla TION 3 1. Cut a 10 /4" square hole in the ceiling using INSTRUCTIONS the locating hole as a center point. The open- Continued 3 3 ing should be framed to 10 /4" x 10 /4" inside dimensions, as shown in Figure 9 on page 9 INSTALLATION FOR vERTICAL using framing lumber the same size as the TERMINATION ceiling joists. If the area above the ceiling is Note: Vertical restrictor must be installed in all an insulated ceiling or an attic, nail firestop
ページ15に含まれる内容の要旨
Venting with One 90° Elbow VENTING INSTalla TION Vertical (V) Horizontal (H) INSTRUCTIONS 5' min. ' max. Continued 6' min. 4' max. 7' min. 6' max. 6. Continue to add pipe sections until the height 8' min. 8' max. of the vent cap meets the minimum building 0' max. 8' max. code requirements described in Figure 7 on page 8. Note: You must increase vent height 45° Elbow for steep roof pitches. Nearby trees, adjoining rooflines, steep pitched roofs and other similar factors may cause po
ページ16に含まれる内容の要旨
When installing this fireplace at an elevation above VENTING INSTalla TION 4500 feet (in Canada), check with local authorities. INSTRUCTIONS IMPORTANT: For horizontal installations Continued above 2,000 feet, it is recommended that a 12" extension pipe be added before starter elbow (see Figure 25) and a round horizontal termi- nation be used. 45° Starter Elbow 1" Extension Vertical Venting V = 40' max. Figure 25 - Recommended 12" Extension Note: Install for High Altitude Installation r
ページ17に含まれる内容の要旨
VENTING INSTalla TION FIREpla CE INSTRUCTIONS INSTalla TION Continued CHECK GAS TYPE Number Description Use proper gas type for the fireplace unit you are VKR-58 Roof Vent Kit, Galvanized installing. If your gas supply is not correct, do not (Includes: 45° Elbow, 7"-1" install fireplace. See retailer where you purchased Adjustable Pipe, Flue Restrictor, the fireplace for proper fireplace according to your Vertical High Wind Termination, gas type or to purchase gas conversion kit
ページ18に含まれる内容の要旨
Speed FIREpla CE Switch Control Blower INSTalla TION Bracket Plug-In Continued 3. Place the blower against the lower rear wall of the firebox outer wrapper with the exhaust port directed upward. The blower will fit inside the back opening and be held in position against the back wall by the magnets (see Figure 26, Duplex Outlet page 17). Control (Located Locknut 4. Be certain that all wire terminals are securely Shaft Control underneath attached to terminals on blower motor an
ページ19に含まれる内容の要旨
Power Cord White FIREpla CE Blue Wire Wire INSTalla TION Black Magnetic Continued Wire Strips 3. Place the blower against the lower rear wall of Thermal Air Flow Switch the firebox outer wrapper with the exhaust port Direction directed upward and the thermodisc positioned up near the fireplace bottom. The thermodisc must be oriented near the fireplace bottom as shown in Figure 29, in order to sense tempera- ture and properly operate. The blower will be Thermal held in position agai
ページ20に含まれる内容の要旨
For propane/LP connection only, the installer must FIREpla CE supply an external regulator. The external regula- INSTalla TION tor will reduce incoming gas pressure. You must Continued reduce incoming gas pressure to between 11" and 14" of water. If you do not reduce incoming gas INSTALLING GAS pIpING TO pressure, fireplace regulator damage could occur. FIRELACE p LOCATION Install external regulator with the vent pointing down as shown in Figure 31. Pointing the vent WARNING: A qualifi
