ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
16” Variable Speed
Wood Lathe
(Models 46-745, 46-746, & 46-765X)
PATENT PENDING
PART NO. 434-10-651-0008 - 04-02-03
Copyright © 2003 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
ページ2に含まれる内容の要旨
SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protect- ing YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols to the right. Please read the manual and pay attention to these sections. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not
ページ3に含まれる内容の要旨
1. FOR YOUR OWN SAFETY, READ THE INSTRUC- 13. USE RECOMMENDED ACCESSORIES. The use TION MANUAL BEFORE OPERATING THE of accessories and attachments not recommend- MACHINE. Learning the machine’s application, ed by Delta may cause damage to the machine or limitations, and specific hazards will greatly mini- injury to the user. mize the possibility of accidents and injury. 14. USE THE PROPER EXTENSION CORD. Make 2. USE CERTIFIED SAFETY EQUIPMENT. Eye pro- sure your extension cord is in good conditi
ページ4に含まれる内容の要旨
ADDITIONAL SAFETY RULES FOR WOOD LATHES FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. 1. DONOTOPERATE THIS MACHINE UNTIL it is 13. CLEAR THE LATHE BED OF ALL OBJECTS (tools, assembled and installed according to the instruc- scraps of wood, etc.) before turning the machine “ON”. tions. 14. EXAMINE THE SET-UP CAREFULLY before turning the 2. OBTAIN ADVICE from your supervisor, instructor, machine “ON”. or another qualified person if you are not familiar with 15. STAND CLEAR,
ページ5に含まれる内容の要旨
POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same ch
ページ6に含まれる内容の要旨
3. Grounded, cord-connected machines intended for GROUNDED OUTLET BOX use on a supply circuit having a nominal rating between 150 - 250 volts, inclusive: CURRENT CARRYING PRONGS If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. C, the machine will have a grounding plug that looks like the plug illustrated in Fig. C. Make sure the machine is con- nected to an outlet having the same configuration as the plug. No adapter is available or s
ページ7に含まれる内容の要旨
FUNCTIONAL DESCRIPTION FOREWORD The Delta 46-745, 46-746, and 46-765X 16” adjustable speed wood lathes are big capacity machines, designed for industry, commercial shops, and schools, wherever a demand for continued accuracy and long life through safe, heavy- duty operation exists. UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened
ページ8に含まれる内容の要旨
ASSEMBLY ATTACHING LATHE BED 58” TO PEDESTALS 1. Remove tailstock, headstock, and tool rest from the lathe bed. NOTE: See “ADJUSTING HEADSTOCK AND TAILSTOCK” and “TOOL REST” for removal/installation instructions. 2. Set pedestals exactly 58” apart (Fig. 5). 3. Because of the weight, use an assistant to place the lathe bed on top of the pedestals. Make sure that the holes in the lathe bed are aligned with the holes in the Fig. 5 tops of the pedestals (Fig. 6) A and B. 4. Attach the lathe bed to
ページ9に含まれる内容の要旨
ATTACHING LEG INSERTS B The lathe is supplied with four leg inserts, one of which is shown (A) Fig. 10. To attach the leg inserts to the pedestals, place one side in the hole provided and gently tap the other side, top, and bottom with a rubber mallet (B) Fig. 10. A Fig. 10 Attach the Headstock (D) Fig. 11, Tool Rest (E) Fig. 11, F E and Tailstock (F) Fig. 11 to the lathe bed (G) Fig. 11. D Notice the tool and centers storage areas located at (H) G Fig. 11, and brackets on the pedestals to acce
ページ10に含まれる内容の要旨
TAILSTOCK LIVE CENTER The tailstock live center (A) Fig. 14, supplied with your lathe, is equipped with a No. 2 Morse Taper shank. NOTE: Before inserting the live center, clean both the shank and the inside of the tailstock to remove any grease or debris. To remove the live center (A) from the D A tailstock spindle (B), use the knockout bar (C) Fig. 14 (supplied) through the hole (D) in the opposite end of the C B spindle. Fig. 14 ADJUSTING CLAMPS ON THE HEADSTOCK AND TAILSTOCK A C The headstock
ページ11に含まれる内容の要旨
STARTING AND STOPPING THE B TOOL The switch (A) Fig. 18 provides electrical power to the adjustable speed drive. Lift the safety cover (B), and move the switch to the “up” position. To turn the power off, simply A push the safety cover (B) down. NOTE: In case of emer- gency, immediately push the safety cover (B) down to shut off power. These machines have a circuit that automat- ically decelerates the spindle once the stop button (C) Fig. 22 on the control panel is pushed. Although an optional d
ページ12に含まれる内容の要旨
6. The REVERSE (REV) button is used FOR SANDING PURPOSES ONLY. NOTE: When using the faceplate, be A B certain that the faceplate locking screw (A) Fig. 23 is tight. NOTE: To remove faceplate, loosen the set screw (A) Fig. 23 two full turns. Use the supplied wrench (B) Fig. 23B to loosen the faceplate, then remove the face plate from the spindle. IMPORTANT: For emergencies, use ONLY the safety cover to stop the machine. Also, when leaving the machine, be certain that the power to the machine is
ページ13に含まれる内容の要旨
OPERATION The following directions will give the inexperienced operator a beginning point for common lathe operations. Practice on scrap material before attempting serious work. LATHE TOOLS Standard wood turning tools come in several different configurations (Fig. 26). The majority of turnings will require the gouge tool (A) Fig. 26. This round nosed hollow chisel is used for roughing cuts, cove cuts and other operations. The skew chisel (B) is a double-ground flat chisel, with an angled end. Th
ページ14に含まれる内容の要旨
After marking each end, mark the true center with a punch awl or dividers (Fig. 29). If the stock is hardwood, the centers should be drilled to a depth of about 1/8”. The spur or live center is then placed against one end of the work and seated by striking with a mallet (Fig. 30). In hardwood, make a starting seat for the spur center by sawing on the diagonal lines, and drilling a small hole at the intersection. After driving the center, hold the center and the work together and fit both immedia
ページ15に含まれる内容の要旨
ROUGHING A CYLINDER The large gouge is used in the first turning operation by smoothing the sharp corners of the work. Run the lathe at low speed and hold the gouge in the manner shown in Fig. 33 The cut starts about 2 inches from the tailstock end and continues from this point to the end of the tail- stock. Make the second pass beginning about 2” or 3” to the left of the first cut. Advance again toward the tailstock, and merge with the previous cut. Toward the end of the Fig. 33 live center, ro
ページ16に含まれる内容の要旨
SMOOTHING A CYLINDER To smooth a cylinder, use a large skew chisel. This requires practice, but experience with this tool is very important. Place the cutting point near the center of chisel and high on the work (Fig. 38). Sometimes, in striv- ing for a certain position in relation to the work, the beginner will often overlook this all-important point. Raising the handle will increase the depth of cut while lowering the handle, of course, does the opposite. As with the gouge, the skew can be adv
ページ17に含まれる内容の要旨
CUTTING A SHOULDER Use the parting tool first to reduce the wood to within 1/16” of the required shoulder and diameter (Fig. 43). Clean the waste stock out with the gouge (Fig. 44), then use the skew for the actual cutting of the shoulder (Figs. 45A and 45B), which is a duplication of squaring an end. The skew then makes the horizontal cut, but in a differ- ent manner from plain cylinder work. If the shoulder is long, use the ordinary skew position for the outer portion of the cut. At the angle
ページ18に含まれる内容の要旨
VEE GROOVES Cutting the vee groove demands much the same technique as the bead, except the skew is hinged straight into the work without rotation (Fig. 51). Only one-half of the vee is made at a time, and one, two, or more cuts may be needed on each side to obtain the desired shape. As in all cutting with the skew, the bevel next to the cut must be used as a fulcrum. Be careful not to allow full edge of the chisel to catch and cause a run. Vee grooves can also be made with the toe of the skew, i
ページ19に含まれる内容の要旨
The gouge is placed on edge on the tool rest so that the grind of the chisel forms an approximate right angle with the work (Figs. 57). The chisel contacts the work at the center of the cutting edge. Hold the tool so that the centerline of the gouge is pointing directly toward the center of the revolving stock. This starting position is important to prevent the gouge from running along the surface of the work. From the starting position, push the gouge into the revolving stock, and roll the tool
ページ20に含まれる内容の要旨
FACEPLATE TURNING Mount turnings that cannot be worked between centers on a faceplate. The greater part of this type of turning is done with the faceplate mounting, although there are a number of jobs which require special chucks. All cutting in faceplate work is done by scraping. Any attempt to use a cutting technique on the edge grain of large work will result in a hogging, gouging cut which may jerk the chisel out of the hands of the operator. Use a band saw on all work to roughly cut the t
