ページ1に含まれる内容の要旨
XK100
Keyboard Amplifier
User’s Guide
ページ2に含まれる内容の要旨
XK100 Keyboard Amplifier Declaration of Conformity Manufacturer’s Name: SLM Electronics Corporate Headquarters: 1901 Congressional Drive, St. Louis, Missouri 63146 Primary Production Facility: 700 Hwy 202 W, Yellville, Arkansas, 72687 Product Type: Audio Amplifier Products meet the regulations for compliance marking under: ETL standards UL6500, UL60065, or UL813 CSA standards E60065 or C22.2 No.1-M90 CE safety standard EN60065 CE EMC standards EN55103 or EN55013 and EN61000 C-tick designation L
ページ3に含まれる内容の要旨
XK100 Keyboard Amplifier Congratulations! You are now the proud owner of the Crate XK100 keyboard amplifier. This ver- satile and great sounding amp features a 15” Crate Custom woofer and two LeSon dome tweeters housed in a ported tuned enclosure. Each of the four discreet chan- nels has its own level and reverb/effect control. Channel 1 also has separate low and high rotary EQ controls, switchable phantom power, and a balanced low impedance mic in jack. The master section features a 5-band grap
ページ4に含まれる内容の要旨
XK100 Keyboard Amplifier 5 8 5 5 5 4 4 4 4 3 7 3 3 3 6 1 2 9 9 9 1. MIC IN: Use this balanced XLR jack to connect a low impedance balanced microphone signal to Channel 1 of the amplifier by means of a shielded microphone cable. 2. LINE IN: Use this balanced 1/4” jack to connect a high impedance microphone or other line level signal to Channel 1 of the amplifier by means of a shielded microphone or instrument cable. NOTE: Both the Mic In and Line In jacks may used simultaneously, however both of
ページ5に含まれる内容の要旨
XK100 Keyboard Amplifier 11 13 10 16 15 12 14 17 18 19 20 21 22 23 9. INPUT: Use this 1/4” jack to connect a keyboard or other line level signal to the corresponding chan- nel by means of a shielded instrument cable. 10. EQUALIZATION: Use this five-band graphic equalizer to shape the output of the amplifier to best suit your tastes and to compensate for room acoustics. 11. REVERB RETURN: Use this control to adjust the overall amount of reverberation applied to the output signal. This control wor
ページ6に含まれる内容の要旨
XK100 Keyboard Amplifier 19. PRE AMP OUT: Use this jack to send a high impedance unbalanced signal from the amplifier to another amplifier or recording device by means of a shielded signal cable. 20. POWER AMP IN: Use this jack to connect a line level signal directly into the internal power amp circuit. When a connector is inserted into this jack, the signals from channels 1-4 are disabled. 21. BAL. LINE OUT: Use this XLR jack to send a balanced line level signal from the amplifier to an externa
ページ7に含まれる内容の要旨
XK100 Keyboard Amplifier System Block Diagram: PEAK CHANNEL 1 TONES LINE PATCH BAY IN LEVEL SEND RETURN REV/ EFFECT MIC EFF LOW HIGH RETURN IN PEAK REVERB CHANNEL 2 RETURN INPUT LEVEL REV/ EFF EQUALIZATION PRE AMP PEAK CHANNEL 3 OUT MASTER INPUT LEVEL PWR AMP REV/ IN BAL. EFF LINE OUT PEAK BAL. LINE OUT/ CHANNEL 4 HEADPHONES LEVEL INPUT (HEAD TWEETERS LEVEL PHONES) REV/ CD INPUT EFF CROSSOVER POWER WOOFER AMP W /LIMITER 7
ページ8に含まれる内容の要旨
XK100 Keyboard Amplifier XK100 TECHNICAL SPECIFICATIONS: Maximum Signal Accepted Ch. 1 High Z: 10 volts peak to peak; Low Z: 15 volts peak to peak Ch.’s 2, 3 and 4: 10 volts peak to peak Input Power Requirements 115 VAC, 60Hz, 110VA 100/110VAC, 50/60Hz, 110VA 230VAC, 50/60Hz, 110VA Nominal Input Impedance Ch. 1 High Z: 10k ohms; Low Z: 600 ohms Ch’s 2, 3 and 4: 24k ohms Gain Ch. 1: High Z: 64dB; Low Z: 70dB; Ch. 2: 57dB; Ch. 3: 57dB; Ch. 4: 57dB Output Power Rating 100 watts @ 5% THD w/4 ohm l
