ページ1に含まれる内容の要旨
™ ™
™ ™ ™
S S S S SIE IE IE IE IENA NA NA NA NA
®
SIENA Owner’s Manual
READ AND SAVE THESE INSTRUCTIONS!
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper
installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and
carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circ
ページ2に含まれる内容の要旨
INTRODUCTION BEFORE YOU START • CAUTION: RISK OF ELECTRICAL SHOCK! All wiring must be performed in accordance with national and local electrical codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating and possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor operated appliance, or transformer-supplied appliance. • This fan is designed to be installed on an existing electrical outlet
ページ3に含まれる内容の要旨
™ ™ ™ ™ ™ S S S S SIE IE IE IE IENA NA NA NA NA MOUNTING RECOMMENDATIONS GENERAL GUIDELINES Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan b
ページ4に含まれる内容の要旨
FAN INSTALLATION GETTING STARTED Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located where you After turning the power OFF at its source (either the circuit wish to place your Casablanca fan, an approved ceiling breaker or fuse box), lower the old fixture and disconnect fixture outlet box must be installed and wired. the wiring. Check the ceiling fixture outlet box to be sure it is marked “Approved for Ceiling Fan M
ページ5に含まれる内容の要旨
™ ™ ™ ™ ™ S S S S SIE IE IE IE IENA NA NA NA NA LAG SCREW INSTALLATION NOTE: This step is required only under two conditions: If the fan weighs 36 lbs. or more or if the existing ceiling fixture outlet box needs to be modified for a ceiling fan application (for example, if the house is not new construction and you are replacing an existing light fixture). We recommend that the ceiling box be of sufficient capacity to support the weight of the fan and light fixture under any conditions. If in do
ページ6に含まれる内容の要旨
FAN PREPARATION PERMA•LOCK™ HARDWARE (not to scale) 9" Perma•Lock™ 3" Perma•Lock™ Downrod Downrod and Ball Assembly and Ball Assembly (for decorative (for non-decora- Uplight Lightbulbs Decorative Arm arm assembly tive arm assembly (4) A-15 40-watt Allen Wrench Assembly installations) installations) Motor Wires IMPORTANT SAFETY INFORMATION: (leave at least 6" long) Before starting the installation of your ceiling Ground Wire fan, install the threaded downrod into the motor (green) coupling and l
ページ7に含まれる内容の要旨
™ ™ ™ ™ ™ S S S S SIE IE IE IE IENA NA NA NA NA FAN PREPARATION (CONT.) Installation/Replacement of Incandescent Lightbulbs Step 5. Remove the two screws from the cover door as shown and lift door from motor. Install a 40-watt S-11 type incandescent lightbulb in the socket. Replace the door and re-insert the screws. Repeat twice more. NOTE: When replacing lightbulbs, be sure to use only 40-watt maximum. BLADE INSTALLATION BLADE HARDWARE (not to scale) Allen Screw Pack C: Blades (5) Blade Screws
ページ8に含まれる内容の要旨
HANGING THE FAN Step 8a. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires are pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. Ball Step 8b. Trim excess motor wires, leaving at least 6 inches 1 2 above the downrod. Strip / -inch insulation from the end of each wire using a wire stripper (available at your local Slot hardware store). Pin CANOPY ELECTRICAL CONNECTIONS
ページ9に含まれる内容の要旨
™ ™ ™ ™ ™ S S S S SIE IE IE IE IENA NA NA NA NA LIGHT KIT INSTALLATION LIGHT KIT HARDWARE (not to scale) Downlight Lightbulbs (3) Glass Shade Light Kit 60-watt A-15 Light Assembly Installation Step 11a. Connect the light assembly connector to the motor connector, as shown. Step 11b. Carefully tuck the wires and align the light assembly with the adapter plate. Step 11c. Screw the finial rod into the adapter plate to secure. Install Glass Shades Step 12a. Remove the three lock rings from the light
ページ10に含まれる内容の要旨
VERSA•TOUCH2™ CONTROL INSTALLATION VERSA•TOUCH2™ HARDWARE (not to scale) Wood Screw Screw 3 Drywall Anchor Screw 6-32 X /8" 6-32 X 1" 12v Battery 6-32 (2) 1" (2) (2) (2) W-73 W-73 Control Control Holder CONTROL BRACKET INSTALLATION SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. CAUTION! Do not use with wall dimmer. Step 14 Follow instructions for the type of transmitter control bracket you will be using. Standard Toggle Roc
ページ11に含まれる内容の要旨
™ ™ ™ ™ ™ S S S S SIE IE IE IE IENA NA NA NA NA REMOTE OPERATION Fan Control DOWNLIGHT To start the fan. Press the selected speed button to run the fan at the desired speed. Send Signal LED LOW=Low speed MED=Medium speed HIGH=High speed UPLIGHT To turn off the fan, press the FAN OFF button. Airflow Direction MED To reverse the airflow, press the REVERSE button. REVERSE operates at any speed HIGH whether the fan is on or off. The fan returns to its set speed after reversing. LOW Light Con
ページ12に含まれる内容の要旨
TROUBLESHOOTING TIPS Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. PROBLEM POSSIBLE REMEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the power is turned off during this inspection. • The battery is weak. Install a fresh battery. • The fan receiver is defective. Replace the fan receiver. • Check the frequency setting: Turn the power off at
ページ13に含まれる内容の要旨
™ ™ ™ ™ ™ S S S S SIE IE IE IE IENA NA NA NA NA CARE RECOMMENDATIONS Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. • A vacuum cleaner brush nozzle can remove heavier dust. • Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish. Blades • Wood-finish blade
ページ14に含まれる内容の要旨
AUTHORIZED SERVICE CENTERS STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE ALABAMA LOVELAND 80538 FIRESIDE LIGHTING INC. 970-669-3540 OWTS MOBILE 36618 AZALEA CITY SERVICE CENTER 251-341-0663 COLORADO SPRINGS 80903 HOME LIGHTING INC. 719-471-3520 OWTS TUSCALOOSA 35405 LTG. & APPL./LIGHTING PLUS 205-345-8900 FORT COLLINS 80525 THE LIGHT CENTER 970-226-3430 OWTS HUNTSVILLE 35816 SOUTHERN HOME & HEARTH INC. 256-534-1715 LONGMONT 80501 LUMENAREA.COM INC. 3
ページ15に含まれる内容の要旨
™ ™ ™ ™ ™ S S S S SIE IE IE IE IENA NA NA NA NA STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE IOWA (CONTINUED) NEBRASKA SIOUX CENTER 51250 HILLS HOME SYSTEMS 712-722-2539 OMAHA 68104 D & L ELECTRONICS 402-571-5233 DES MOINES 50311 ADVANCED LIGHTING 515-255-5009 OWTS GRAND ISLAND 68803 QUALITY SEW & VAC. 308-382-7310 ISO MONTICELLO 52310 REM ELECTRIC INC. 319-465-3346 OMAHA 68144 OAK HILLS ELECTRIC INC. 402-691-4567 CARROLL 51401 J & L ELECTRIC INC. 7
ページ16に含まれる内容の要旨
STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE OHIO (CONTINUED) AUSTIN 78757 KLOCK ELECTRIC 512-837-4704 CLEVELAND 44109 WESTSIDE LTG. CTR. 216-459-1970 GIDDINGS 78942 ORSAG’S INC. 409-542-3167 N. OLMSTED 44070 CHANDELIER SHACK INC. 440-777-6969 ISO LUBBOCK 79413 ORECK VACUUMS 806-792-2821 NORTH LIMA 44452 DICKEY ELECTRIC 330-549-3976 ARLINGTON 76001 P&M QUALITY CONT. 817-478-2004 SOUTH EUCLID 44121 LAMPSHADER EAST/DBA LTG. EXPO 216-291-3030 OWTS/ISO
