ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
85” Snowblower TABLE OF CONTENTS DESCRIPTION PAGE Warranty......................................................................1 Safety Instructions.......................................................2 Safety Sign Locations ..................................................3 Assembly Instructions..................................................4 Operating
ページ3に含まれる内容の要旨
85” Snowblower WARRANTY POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months (90 days for commercial application) from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications. Buhler Manufacturing’s obligations under this warranty shall be limited t
ページ4に含まれる内容の要旨
85” Snowblower CAUTION 1. Always review operator’s manual before starting new machine. 2. Do not let inexperienced operators or children run this equipment. 3. Never service or clean unit while it is running. 4. Do not remove shields. 5. Stay clear of augers. 6. Stay clear of discharge chute. Rocks can be picked up and thrown. 7. P
ページ5に含まれる内容の要旨
85” Snowblower SNOWBLOWER This manual covers the 85” model snowblower. When ordering parts, be sure to list the serial number of your unit and blower width. The snowblower is the push type and will mount to a tractor with a category 1 or 2 three point hitch and 540 rpm PTO. The 85" model has a single auger and comes with a hydraulic control for the chute with a manual control available a
ページ6に含まれる内容の要旨
85” Snowblower BASIC ASSEMBLY INSTRUCTIONS STEP 1. Assemble the snow chute, referring to instructions under the appropriate heading for “manual chute” or “hydraulic chute”. STEP 2. Check the gearbox and fill to the lower level with a winter grade transmission oil. STEP 3. The snowblower is shipped with lower three point hitch pins for a category 2 hitch. STEP 4. Using tape or bright colo
ページ7に含まれる内容の要旨
85” Snowblower OPERATING INSTRUCTIONS 1. Adjust the top link of the tractor hitch so that the snowblower is level when resting on the ground. 2. Adjust the lower link sway chains or blocks on the tractor to restrict side movement of the blower when operating. 3. Run the blower at low RPM to check operation. 4. The snowblower has two shear bolts to protect the tractor and blower in
ページ8に含まれる内容の要旨
85” Snowblower 85" ALLIED SNOWBLOWER - 6 -
ページ9に含まれる内容の要旨
85” Snowblower - 7 -
ページ10に含まれる内容の要旨
85” Snowblower WHEN ORDERING PARTS Always give your dealer the Model, Color and Serial Number of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part. 85'' ALLIED SNOWBLOWER PARTS LIST Item # Part # Description 1 905612 Snowblower Main Weldment 2 21598 Fa
ページ11に含まれる内容の要旨
85” Snowblower 33 81636 1/2'' Hex Nut (pl) 34 812364 1/2'' Lock Nut (pl) 35 81592 3/8'' Hex Nut (pl) 36 84217 3/8'' Wing Nut (pl) 37 812362 5/16'' Lock Nut (pl) 38 81701 3/4'' Lock Washer (pl) 39 81678 5/8'' B.S. Flat Washer (pl) 40 81637 1/2'' Lock Washer (pl) 41 81593 3/8'' Lock Washer (pl) 42 936402 PTO Safety Chain 43 965911 7/16'' Linch Pin 44 988999 3/8'' x 3/8'' Socket Set Scre
ページ12に含まれる内容の要旨
85” Snowblower MANUAL CHUTE CONTROL 1. Remove spout clamp and install chute. 2. Mount handle brackets to snowblower & hitch. 3. Insert handle extension, placing a 1” flat washer on both sides of the front handle bracket; secure with 3/16 cotter pin. 4. Attach handle to handle extension. 5. Turn chute away from handle. 6. Attach end of cable with cable bolt. 7. Wrap cable clockwise around
ページ13に含まれる内容の要旨
85” Snowblower 85'' Manual Chute Control Item # Part # Description 1 965648 Spout Weldment 2 965970A Spout Clamp 3 102157 Crank Handle 4 108014 Handle Extension 5 108015 Handle Bracket 6 108020 Handle Bracket 7 108019 Cable Bolt 8 108265 Chute Cable 3/16'' x 66'' 9 81207 3/16'' x 2'' Cotter Pin 10 811631 1/4'' x 1 1/2'' Hex Bolt (pl) 11 961658 1/4'' Cable Clamp 12 812363 3/8
ページ14に含まれる内容の要旨
85” Snowblower HYDRAULIC SNOW CHUTE NOTE: Before mounting chute, apply a heavy coating of light grease to chute ring. 1. Remove spout clamp and mount chute. 2. Mount pivot arm. NOTE: Flat Washers are supplied for height spacer if required. 3. Connect one end of cable to pivot arm with cable clamp. 4. Wrap cable completely around chute ring. Then return to pivot arm and connec
ページ15に含まれる内容の要旨
85” Snowblower 85'' Hydraulic Chute Control Item # Part # Description 1 965648 Discharge Chute 2 965970A Spout Clamp 3 108979 Cable Pivot Arm 4 107780 Chute Cable 5 961658 1/4'' Cable Clamp 6 965646 Spout Adjustment Bar 7 961876 1/2'' x 1 3/8'' Clevis Pin 8 961012 #16 Hair Pin Clip 9 967140 1'' Flat Washer 10 812435 1/4'' x 1 3/4'' Cotter Pin 11 81552 5/16'' x 1 1/4'' Hex Bol
ページ16に含まれる内容の要旨
85” Snowblower 85” ALLIED SNOWBLOWER PTO - 14 -
ページ17に含まれる内容の要旨
85” Snowblower SNOWBLOWER PTO (STANDARD) Item # Part # Description F842 Shaft Complete 936263 Tractor Half of PTO (Shear) 936264 Implement Half of PTO (Clamp Yoke) 1 936277 Shear Assembly 2 936199 Safety Slide Lock Repair Kit (Collar, Spring, Ret. Ring, 2-Pawls) 3 936249 Shear Assembly Repair Kit (3/8'' x 1/2'' Bolt, Lube, Blank, 31 - 1/4'' Balls) 4 903296 Shear Bolt - 5/1
ページ18に含まれる内容の要旨
85” Snowblower SNOWBLOWER PTO (OPTIONAL LONG) Item # Part # Description F844 Shaft Complete 936285 Tractor Half of PTO (Shear) 936280 Implement Half of PTO (Clamp Yoke) 1 936277 Shear Assembly 2 936199 Safety Slide Lock Repair Kit (Collar, Spring, Ret. Ring, 2-Pawls) 3 936249 Shear Assembly Repair Kit (3/8'' x 1/2'' Bolt, Lube, Blank, 31-1/4'' Balls) 4 903296 Shear Bolt -
ページ19に含まれる内容の要旨
85” Snowblower GEAR BOX ASSEMBLY - 17 -
ページ20に含まれる内容の要旨
85” Snowblower GEARBOX ASSEMBLY PARTS LIST - BU50505 Item # Part # Description 1 BU575901 Bearing Cone (13687) 2 BU575902 Bearing Cup (13620) 3 BU50444 Staking Lock Nut 4 BU50417-1 Key 5 BU50310 Gear Box Casting 6 BU50502 Pinion Shaft 7 BU50507 Cross Shaft 8 BU50422-1 Oil Seal 9 BU50415 Retaining Ring 10 BU50414-1 0.005 Shim 11 BU50414-2 0.010 Shim 12 BU50414-3 0.020 Shim 13
