ページ1に含まれる内容の要旨
LAP30EULBA
LAP30EULFR
NOTEBOOK CART ASSEMBLY
WITH TIMER
Assembly Instructions for:
LAP30EULBA
INTERIOR E-UNIT
REPOSITIONING / REPLACEMENT
CAUTION: RISK OF ELECTRICAL SHOCK.
AND
DO NOT PLUG INTO ANOTHER
RELOCATABLE POWER TAP.
TIMER REPLACEMENT
Parts List
Qty. Part No. Description
NO TV/MONITOR TO BE
1 LAP30EULBA Cart Assembly, e-units at back
USED ON TOP OF CART
LAP30EULFR Cart Assembly, e-units at front
Tools Required
MAXIMUM WEIGHT OF ACCESSORIES
Philips screwdriver ON TOP OF CART: 25 LBS.
Th
ページ2に含まれる内容の要旨
E-Unit power timer assembly cord bottom shelf Front View bracket assembly bracket DETAIL 'B' assembly clip DETAIL 'A'
ページ3に含まれる内容の要旨
front-left front-right Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. DETAIL 'C' Step 3 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DETAIL 'C').
ページ4に含まれる内容の要旨
mounting tab DETAIL 'D' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside.
ページ5に含まれる内容の要旨
cutout window clip-rear Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to the rear of cart. 3. Tilt in and set bottom in back, in front of rear panel cutout window. 4. Grip the top and tilt to the upright position, underneath top panel bracket. When repositioned correctly, the E-Unit power switch should be visible from rear panel cutout window. Reinstall the E-Unit bracket assemblies
ページ6に含まれる内容の要旨
tab notch Step 6 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'E' Step 7 Reinstall 18 screws to rear panel that will secure the 9 interior shelves (see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS. Installation is now complete and ready for
ページ7に含まれる内容の要旨
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPOSITIONING: 'REAR TO FRONT' DETAIL 'A' Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
ページ8に含まれる内容の要旨
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and unclip the power cords from the clips at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove all 4 bracket assemblies (see DETAILS 'C' and
ページ9に含まれる内容の要旨
DETAIL 'C' DETAIL 'D' rear-left rear-right Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
ページ10に含まれる内容の要旨
notch tab Step 4 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'F' Step 5 Reinstall 18 screws to rear panel that will secure the 9 interior shelves (see DETAIL 'F'). DO NOT OVER TIGHTEN SCREWS.
ページ11に含まれる内容の要旨
offset clip Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly, the E-Unit power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bra
ページ12に含まれる内容の要旨
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPLACEMENT: 'REAR LOCATION' DETAIL 'A' Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
ページ13に含まれる内容の要旨
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the clip(s) at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove each bracket assembly (see DETAILS 'C
ページ14に含まれる内容の要旨
DETAIL 'C' DETAIL 'D' rear-left rear-right Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
ページ15に含まれる内容の要旨
cutout window rear-left rear-right clip Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly, the E-Unit(s) power switch should be visible from rear panel cutout window. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bracket assembly) and tighten screws securely. Plug in the E-Unit(s) power cord(s) into the bottom outlet(s) of th
ページ16に含まれる内容の要旨
tab notch Step 5 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'E' Step 6 Reinstall 18 screws to rear panel that will secure the 9 interior shelves (see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS. Installation is now complete and ready for
ページ17に含まれる内容の要旨
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPLACEMENT: 'FRONT LOCATION' SEE DETAIL 'B' bottom shelf SEE DETAIL 'A' Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the bottom of cart. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be
ページ18に含まれる内容の要旨
bracket bracket assembly assembly clip DETAIL 'B' DETAIL 'A' front-left front-right Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
ページ19に含まれる内容の要旨
front-left front-right bottom shelf Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly, the E-Unit(s) power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bracket assembly) and tighten screws securely. Plug in the E-Unit power cord(s) into the bottom outlet(s) of the timer assembly (located unde
ページ20に含まれる内容の要旨
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING TIMER REPLACEMENT: 'E-UNIT AT REAR LOCATION' DETAIL 'A' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
