ページ1に含まれる内容の要旨
Installation/Operation
Home Laundry
Automatic
Clothes Dryers
D715I
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 510988R2
www.comlaundry.com June 2007
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
WARNING FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death. W033 • Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. • Installation and service must be performed by a qualified installer or service agency. W257 510988 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 1
ページ4に含まれる内容の要旨
Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510988 2
ページ5に含まれる内容の要旨
Replacement Parts.............................................................................. 9 Table of Safety Information.............................................................................. 11 Explanation of Safety Messages........................................................... 11 Contents Important Safety Instructions ............................................................... 11 Installation.................................................................................
ページ6に含まれる内容の要旨
Motor Overload Protector..................................................................... 32 Lint Filter.............................................................................................. 32 Before You Call for Service ................................................................. 33 If Service Is Required ........................................................................... 34 Information for Handy Reference......................................................... 35 © C
ページ7に含まれる内容の要旨
Replacement Parts If replacement parts are required, contact the source Alliance Laundry Systems from which you purchased your dryer or contact: Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. Phone: (920) 748-3950 for the name and address of the nearest authorized parts distributor. 510988 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5
ページ8に含まれる内容の要旨
Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 510988 6
ページ9に含まれる内容の要旨
Safety Information Explanation of Safety Messages Important Safety Instructions Throughout this manual and on machine decals, you Save These Instructions will find precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific WARNING instructions. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine. To reduce the risk of fire, electric shock, or injury to persons when using your dryer, follow these b
ページ10に含まれる内容の要旨
Safety Information 12. Always clean the lint filter after every load. A 22. Remove laundry immediately after the dryer layer of lint in the filter reduces drying efficiency stops. and prolongs drying time. 23. Always read and follow manufacturer’s 13. Keep area around the exhaust opening and instructions on packages of laundry and cleaning adjacent surrounding area free from the aids. Heed all warnings or precautions. To reduce accumulation of lint, dust and dirt. the risk of poisoning or c
ページ11に含まれる内容の要旨
Installation Roughing In Dimensions 56.85 cm (22.38 in.) 39.1 cm (15.4 in.) 20.3 cm (8.0 in.) *11.4 cm (4.5 in.) 1.1 cm 59.7 cm 71.1 cm (0.4 in.) 68.3 cm (23.5 in.) (28 in.) (26.9 in.) DRY2188N *10.2 cm (4.0 in.) *With leveling legs turned into base. DRY2188N 510988 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9 *91.4 cm (36 in.) *102.24 cm (40.25 in.) *109.2 cm (43 in.) *39.2 cm (15.44 in.)
ページ12に含まれる内容の要旨
Installation Tools Installing the Dryer For most installations, the basic tools you will need Step 1: Position and Level the Dryer are: For further assistance refer to section on Location Requirements. Place the dryer in position, and adjust the legs until the 2 dryer is level from side to side and front to back. 1 3 2 1 4 D822I D259I 3 D669I 1 Wrench D669I 2 Screwdrivers 1Dryer Base 3Level 2Level 4 Duct Tape 3 Leveling Leg Figure 1 Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NO
ページ13に含まれる内容の要旨
Installation Step 2: Connect Dryer Exhaust System Refer to sections on Location Requirements and Dryer Exhaust Requirements. WARNING A clothes dryer produces combustible lint. To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors. W116 NOTE: Failure to exhaust dryer properly will void warranty. NOTE: Venting materials are not supplied with the dryer (obtain locally). DO DON’T D314I D315I Figure 3 510988 © Copyright, Alliance Laundry Systems
ページ14に含まれる内容の要旨
Installation Step 3: Connect Electrical Cord (240 Volt/60 Hertz) Refer to section on Electrical Requirements. D679I TWO-WIRE CONNECTION THREE-WIRE CONNECTION D703I D703I D679I NOTE: Dryer is shown with access cover removed for illustration purposes only. NEVER operate dryer with access cover removed. Figure 4 Step 4: Wipe Out Inside of Dryer Step 5: Connect the Dryer to Electrical Power Before using dryer for the first time, use an all-purpose cleaner, or a detergent and water solution, and
ページ15に含まれる内容の要旨
Installation Reversing Door Procedure The door on this dryer is completely reversible. To reverse door proceed as follows: 1 2 D675I D311S D311S D675I 3 4 B A D273P D312S D312S 5 6 B A D314S D315S D315S D314S 7 8 D316S D316S D620I D620I 9 D623I D623I 510988 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13
ページ16に含まれる内容の要旨
Installation 1. Remove the screw and terminal block access Electrical Requirements cover from the rear of dryer cabinet. 240 Volt, 60 Hertz, 2-Wire 2. Insert ends of direct wire through power supply Plus Grounded (Earth) Wire Installation hole (containing proper strain relief) in rear of dryer cabinet. Connect the power cord, or direct wiring, to the two outer terminal block WARNING terminals using the two wire-binding (10 - 32 x 3/8 inch) screws from the accessories pack in the To reduce
ページ17に含まれる内容の要旨
Installation WARNING 1 2 Dryer is shown with the access cover 3 13 removed for illustration purposes only. To reduce the risk of an electric shock, serious injury or death, NEVER operate the 12 dryer with the access cover removed. 4 W157 11 5 2 1 WIRE CONNECTION 10 DETAIL 8 9 6 7 4 D703I 3 D703I 1 Earth (Ground) Wire (Green/Yellow) D821I 2 Not Used on Gas Models 1 30 Amp Fuse 3 “L” Terminal 2 240 Volt Supply 4 Terminal Block 3 Terminal Block in Dryer 5 Hex Head Screws (Slotted) 4 Rear Bulk
ページ18に含まれる内容の要旨
Installation 240 Volt, 60 Hertz, 3-Wire Grounding Instructions This dryer must be connected to a grounded metal, NOTE: The wiring diagram is located inside the permanent wiring system; or an equipment-grounding control hood. conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. WARNING To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest edition of the
ページ19に含まれる内容の要旨
Installation 1. Remove access cover from rear of dryer. 2. Use a strain relief and insert end of power cord through power supply hole. 2 1 3. Use the three screws from the envelope located in the cylinder to attach the power cord wires to the terminal block. 4. Tighten all screws and reinstall access cover removed in step 1. 3 D286I 1 “L1” Terminal 2 Neutral Terminal 3 “L2” Terminal Figure 9 510988 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17
ページ20に含まれる内容の要旨
Installation The dryer must not be installed or stored in an area Location Requirements where it will be exposed to water and/or weather. Select a location with a solid floor. Dryers installed in The dryer needs sufficient clearance and an adequate residential garages must be elevated 46 cm (18 inches) air supply for proper operation and ventilation, and for above the floor. easier installation and servicing. (Minimum clearances No other fuel burning appliance should be installed in are s
