ページ1に含まれる内容の要旨
MODEL
AR-162S
DIGITAL LASER COPIER
OPERATION MANUAL
Page
• GETTING STARTED 2
• MAKING COPIES 13
• STATUS INDICATORS 28
• GENERAL INFORMATION 35
• OPTIONAL EQUIPMENT 53
ページ2に含まれる内容の要旨
FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the copier’s serial number located on the back of the unit. AR-162S Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number CAUTIONS Follow the cautions below when using this copier. The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. The socket-outle
ページ3に含まれる内容の要旨
STATUS OPTIONAL GETTING STARTED MAKING COPIES INDICATORS GENERAL INFORMATION EQUIPMENT CONTENTS Page GETTING STARTED INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . 4 – Overall layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 – Operation panel . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
GETTING STARTED Introduction INTRODUCTION This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarize yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. Conventions used in this manual In this manual, the following icons are used to provide the user with information pertinent to the use o
ページ5に含まれる内容の要旨
GETTING STARTED Main features GETTING ST GETTING STAR ARTED TED MAIN FEATURES High-speed laser copying First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on). Copying speed is 16 copies/min., which adapts to business use, allowing improvement of working efficiency. High-quality digital image High-quality copying at 600 dpi is performed. In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps. The photo mode
ページ6に含まれる内容の要旨
GETTING STARTED GETTING STARTED Part names and functions PART NAMES AND FUNCTIONS Overall layout Paper tray Platen cover Holds 250 sheets of copy paper. Place the original on the original table and close the platen cover before copying starts. Side cover Original table Open to remove misfeeds and to service the copier. Place the document to be copied here. Side cover handle Handles Lift and pull to open the side cover. Use to move the copier. Bypass tray guides Power switch Adjust to the width o
ページ7に含まれる内容の要旨
GETTING ST GETTING STAR ARTED TED Part names and functions GETTING ST GETTING STAR ARTED TED PART NAMES AND FUNCTIONS Toner cartridge lock release lever Fusing unit release levers Use to unlock the toner cartridge. Lower to remove misfed paper. The fusing unit is hot. Toner cartridge Take care in removing paper. Contains toner. Photoconductive drum Paper guide Copy images are formed on the photoconductive drum. Open to remove misfed paper. Roller rotating knob Turn to remove misfed paper. Access
ページ8に含まれる内容の要旨
GETTING STARTED GETTING STARTED Part names and functions PART NAMES AND FUNCTIONS Operation panel INTERRUPT key and indicator (p. 25) POWER SAVE indicator (p. 42) Interrupts a copy run. Lights up when the copier is in a power save mode. Copy quantity display SPF indicator (p. 55) Displays the specified copy quantity during the ready Lights up when originals are set in the optional SPF. condition and displays the copy countdown as copies are made. Also see items and . Output tray full indicator
ページ9に含まれる内容の要旨
GETTING STARTED GETTING STARTED Part names and functions GETTING ST GETTING STAR ARTED TED PART NAMES AND FUNCTIONS Zero key TRAY SELECT key (p. 14) Use as part of numeric keys to enter copy quantity. Use to manually select a paper tray. Press during a continuous copy run to display the number of copies completed in the current run. AUTO IMAGE key and indicator Press and hold during standby to display the total output Press for automatic copy ratio selection. count. 1st display 2nd display Paper
ページ10に含まれる内容の要旨
GETTING STARTED Copier installation COPIER INSTALLATION Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use. Do not install your copier in areas that are: damp, humid, or ver
ページ11に含まれる内容の要旨
GETTING STARTED Cautions on handling GETTING ST GETTING STAR ARTED TED CAUTIONS ON HANDLING Be careful in handling the copier as follows to maintain the performance of this copier. Do not drop the copier, subject it to shock or strike it against any object. Store spare toner cartridges in a cool dry place without removing from the package before use. If they are exposed to direct sunlight or excessive heat, poor copies may result. Do not touch the photoconductive drum (green portion). Scratches
ページ12に含まれる内容の要旨
GETTING STARTED Loading copy paper LOADING COPY PAPER To save space, this copier has been designed with an adjustable front-loading tray, which is easily opened for paper loading. For best results, use only SHARP recommended paper. (See page 49.) The paper required ( ) indicator will light up when there is no copy paper in the selected paper feed station, or when the paper tray is not installed or is improperly installed. When the paper size is changed in the paper tray, the size of the paper m
ページ13に含まれる内容の要旨
GETTING STARTED Loading copy paper GETTING ST GETTING STAR ARTED TED LOADING COPY PAPER Changing the copy paper size in the tray Gently lift and pull out the paper tray until it stops. 1 Push the pressure plate down until it locks in place. 2 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper. 3 Left guide Move the left guide to the appropriate slot as marked on the tray. 4 Front guide When using 11" x 17" copy paper, store the left guide in the
ページ14に含まれる内容の要旨
GETTING STARTED Loading copy paper LOADING COPY PAPER To set the selected paper size, press the PAPER SIZE ENTER key. 8 The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light up steadily. All other indicators except the START key indicator will go out. If copying is being performed, paper size setting cannot be made. Use the ORIGINAL SIZE ENTER key to select the paper size which is set. 9 Each time the ORIGINAL SI
ページ15に含まれる内容の要旨
MAKING COPIES Auditing accounts AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 38 for setting the auditing mode. If the copier has been programmed in the auditing mode, “–––” will appear in the copy quantity display in the initial conditions. Enter your account number using the numeric keys. 1 As each digit is entered, the dashes in the copy quantity display will disappear. Af
ページ16に含まれる内容の要旨
MAKING COPIES Normal copying NORMAL COPYING Turn the power switch on. It will take about 35 seconds for the copier to warm up. However, you 1 Power on can make desired settings and press the START key during warm-up. Copying will start after warm-up. If the copier has been programmed in the auditing mode, the START key indicator will not light up and “–––” will appear in the copy quantity display. Enter an assigned 3-digit account number. See page 13. If the power is already on and all ind
ページ17に含まれる内容の要旨
MAKING COPIES Normal copying NORMAL COPYING For manual copy density adjustment, press the AUTO/MANUAL/ PHOTO key to select MANUAL and adjust with the light ( ) and dark ( ) keys as desired. For photographs, select PHOTO and then adjust with the light ( ) and dark ( ) keys as desired. There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.) If exposure level 2 is selected, the two left-handmost indicators for that level will light up simult
ページ18に含まれる内容の要旨
MAKING COPIES Reduction/enlargement/zoom REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the PRESET RATIO selector ( , ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. Automatic Place the original on the original table and close the platen cover. 1 Press the ORIGINAL SIZE ENTER key until the indicator for the size of the original on
ページ19に含まれる内容の要旨
MAKING COPIES Reduction/enlargement/zoom REDUCTION/ENLARGEMENT/ZOOM Manual Place the original on the original table and close the platen cover. 1 Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio. 2 To select a preset reduction or enlargement copy ratio, press the or key repeatedly until the indicator for the desired copy ratio is lit. A. Preset reduction ratios are: 95%, 77%, 64%, and 50% . B. Preset enlargement ratios are: 121%, 129%, 141%, a
ページ20に含まれる内容の要旨
MAKING COPIES Bypass feed (special paper) BYPASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. For special purpose papers, the original image must be smaller than the paper or media for copying. If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies. Also for standard copy paper, smudges may appear if t
