ページ6に含まれる内容の要旨
CHAPTER 1 IMPORTANT! PLEASE READ FIRST. CAUTION LABELS Caution labels have been attached to the copier at the following locations for safety purposes. BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when removing a paper jam or when replacing toner. Label 2 High temperature inside. Do not touch parts in this area, because there is a danger of getting burned. .................... Label 1 High voltage inside. NEVER touch parts in this area, because there is a danger of electric shock. ..
ページ7に含まれる内容の要旨
INSTALLATION PRECAUTIONS Environment Power supply/Grounding the copier CAUTION WARNING • Avoid placing the copier on or in locations which are • DO NOT use a power supply with a voltage other unstable or not level. Such locations may cause the than that specified. Avoid multiple connections in the copier to fall down or fall over. This type of situation same outlet. These types of situations present a presents a danger of personal injury or damage to the danger of fire or electrical sh
ページ8に含まれる内容の要旨
PRECAUTIONS FOR USE Other precautions Cautions when using the copier • DO NOT place heavy objects on the copier or cause WARNING other damage to the copier. • DO NOT place metallic objects or containers with water (flower vases, flower pots, cups, etc.) on or • DO NOT open the front cover, turn off the main near the copier. This of situation presents a danger of switch, or pull out the power plug during copying. fire or electrical shock should they fall inside. ............. • During copyin
ページ9に含まれる内容の要旨
CHAPTER 2 NAMES OF PARTS (1) Main body 18 ppm copier 15 ppm copier 3 21 ° 21 5 6 4 4 7 9 7 9 ¤ 8 ¤ 8 fi fi ! ! @0 fl‹› ( @0 fl‹› ( ⁄ ) * & % $ ^ # ‡ 2-1
ページ10に含まれる内容の要旨
CHAPTER 2 NAMES OF PARTS 1 DF (Document Feeder) (Open/close to set the original on the platen.) 2 Original table (Place the originals here.) 3 Original insertion guides (Adjust the guides to the width of the originals.) 4 DF open/close handle (Hold this handle when opening and closing the DF.) 5 Original eject cover (Copied originals are stored here.) 6 DF original switchback cover (Open this cover to remove a misfed original from the DF.) 7 Operation panel (Contains the keys and indicators for
ページ11に含まれる内容の要旨
CHAPTER 2 NAMES OF PARTS Inch specifications ) ( * ! 0^ 9 4 ⁄ %&@$# 7 8 65 3 2 1 European metric specifications ) ( * ! 0^ 9 4 ⁄ %&@$# 7 8 65 3 2 1 Asia and Oceania metric specifications ) ( * ! 0^ 9 4 ⁄ %&@$# 7 8 65 3 2 1 2-3
ページ12に含まれる内容の要旨
CHAPTER 2 NAMES OF PARTS Initial mode (at the end of warm-up or when the Reset key is (2) Operation panel pressed) 1 Start key (indicator) In the initial mode, the upper drawer is selected as the paper feed (Press to start copying. Copying is possible when the indicator is lit drawer, the number of copies is set to “1” and the image mode is green.) set to “Text & Photo”. 2 Stop/Reset key * If the optional drawer is installed, the drawer selected in the initial (Stop: Interrupts or aborts copy
ページ13に含まれる内容の要旨
CHAPTER 3 PREPARATIONS BEFORE USE 1. How to load paper Paper can be loaded into the drawer and the multi-bypass. Press the drawer bottom plate down and lock it there. 2 (1) Precautions for loading paper After unpacking the paper, ruffle it several times and then load into the tray. Holding the width adjustment lever, move it to align the width 3 guide with the required paper width. Paper sizes are marked inside the drawer. (2) Loading paper into the drawer 2 Up to 250 sheets of standard paper (6
ページ14に含まれる内容の要旨
CHAPTER 3 PREPARATIONS BEFORE USE * If the paper reaches the right-hand wall of the drawer, the Gently push the drawer back in. 6 length guide is not used. Store it in the space shown in the * If you force the drawer in, the paper may come out from illustration. under the claw. NOTE Leaving paper out of its package under high temperature and high humidity conditions may lead to problems caused by ambient moisture. After loading paper into drawers, store the remaining paper sealed in the paper s
ページ15に含まれる内容の要旨
CHAPTER 3 PREPARATIONS BEFORE USE Pull out the support guide. IMPORTANT 2 * When loading paper into the multi-bypass, make sure that the copy side is facing downward. (The copy side is the side facing upward when the package is opened.) If the leading edge of the paper is curled, straighten it out before loading the paper in the multi-bypass. * Do not leave paper loaded in the multi-bypass when it is not used. If you do, a paper misfeed may occur. * When loading paper into the multi-bypass, pla
ページ16に含まれる内容の要旨
CHAPTER 3 PREPARATIONS BEFORE USE Select the paper size by changing the display indication Open the multi-bypass. 2 1 using the Paper Select key. (Inch specifications) (Metric specifications) Pull out the support guide. 2 The display indication can also be changed using the Number of Copies/Zoom (+) key or Number of Copies/Zoom (-) key. (English text panel) (Symbol panel) Adjust the insert guides to the width of the envelope to be 3 loaded. Press the Zoom Input/Enter key. The multi-bypass indic
ページ17に含まれる内容の要旨
CHAPTER 3 PREPARATIONS BEFORE USE 2. How to set originals Setting originals (1) Setting originals into the DF Precautions for the use of DF Adjust the original insertion guides to the original size. 1 Do not use any of the originals given below with the DF. Also do not * Before setting the originals in the DF, check that no original set originals with punch holes or tear-off strips positioned as the from the previous operation remains on the original eject leading edge. cover. Originals remaini
ページ18に含まれる内容の要旨
CHAPTER 3 PREPARATIONS BEFORE USE 15 ppm copier (2) Setting an original on the platen When an original is set in the DF, copying will automatically start (see When using an original that cannot be set in the DF, such as a book “DF auto start” on page 6-3). or magazine, open the DF and place it on the platen. * Enlargement and reduction copying is not possible when the DF is used. Holding the DF open/close handle, open the DF. 1 * Before opening the DF, check that no original is present on Ori
ページ19に含まれる内容の要旨
CHAPTER 3 PREPARATIONS BEFORE USE 3. Replacing the toner container and waste toner tank When the level of toner becomes low, the Add Toner indicator lights Open the front cover. 1 and a toner replacement message is printed out. When the message is printed, replace the toner container and waste toner tank immediately. It is still possible to make copies, one at a time, with the indicator lit. However, if copying is continued under this condition, the Start indicator will eventually go off and co
ページ20に含まれる内容の要旨
CHAPTER 3 PREPARATIONS BEFORE USE Slide the toner container to the left and then pull it out toward Install the toner container. 4 7 you. * First insert the toner container into the copier as far as it will go and then slide it to the right as indicated by the marked arrows. WARNING High voltage is present in the charger section. Take Install the waste toner tank. sufficient care when working in this area, as there is a 8 danger of electrical shock. Gently pull the cleaning shaft out as far as
