ページ1に含まれる内容の要旨
™
Installation Guide
CO2075FF —
Ice Maker/Refrigerator
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 FAX (414) 354-5696
OnlineService@U-Line.com
©2005 U-Line Corporation
02/2005
ページ2に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator Contents 1 Follow Safety Precautions Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IMPORTANT Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PLEASE READ all instructions completely before Door Swing/Clearances Information . . . . . . . . . . . . . . 5 attempting to install or operate the unit. Reversing the Door. . . . .
ページ3に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed You have received a carton containing your CO2075FF throughout this guide: Ice Maker/Refrigerator with a package inside containing a User Manual, a Product Registration WARNING Card and water connection parts. Complete and mail the Product Registration Card or register online at SHOCK HAZARD — Electrical Gr
ページ4に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator After all the protective coating has been removed from 3 Prepare Site the unit/door, clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft Your U-Line product has been designed for either free- cloth. Do NOT use abrasive cleaning agents. standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rea
ページ5に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator Product Dimensions Reversing the Door (Black and White Units Only) 23-11/16" 25-13/16" All U-Line units (except Including Including Handle Handle Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side. The top hinge hardware will be used on the 34-1/8" 34-1/8" bottom of the other side and the bottom hinge hardware will be used on the top of the other side (see
ページ6に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator 4. Remove the two door closer inserts from the existing Other Site Requirements bottom hinge and install as shown on the new bottom hinge (see Figure 8). Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 14. Hinge Screw Water Supply Pin Door The unit requires a 1/4-inch OD water supply line and a Closer shut-off valve. For more information see Page 13. Inse
ページ7に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator Side-By-Side Installation 4 Prepare and Install Door Panel Instructions (Black and White Units Only) For a complete refreshment center, install your CO2075FF Ice Maker/Refrigerator beside a U-Line Drawer or Wine Two types of custom door panels can be installed on your Captain Model (see Figure 11 for typical cut-out). Note Black or White unit to harmonize with or accent the that each Side-By-Side Installation will be different. surrounding décor: a Custo
ページ8に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit (P/N U-OL2075B — Black or P/N U-OL2075W — White). Appropriate hardware, Modified Handle, Replacement Hinges and a copy of these instructions will be included in the kit. 1. Cut the overlay to the following dimensions (see Figure 15). Figure 1
ページ9に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator 4. Drill hole for upper door hinge (top of panel) (see 13/32" 0.177" Dia. (#16 Drill) Figure 16, Top View). 13/32" x 11/16" Deep 0.177" diameter 3/8" (#16 drill) x 11/16" deep 3/8" 5. Drill hole for lower door hinge (see Figure 16, Bottom Door Bottom: 13/16" View). x 5/16" Dia. 1/4" Deep x Chamfer 1/32" 45° 5/16" diameter x 1/4" deep Top View Bottom View CAUTION It is important to ensure that all drilled holes are drilled to 1/8" 1/8" 13/32" 1/8" the cor
ページ10に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator 5. Remove the top handle and discard. (This handle will be Tape replaced with the Modified Handle included in the Full Back of Removed Wood Overlay Door Panel Kit.) Door Panel Panel 6. Remove the two screws located on both sides of the lower handle. Remove the handle. 7. Attach the Modified Handle to the lower handle using the three screws removed in Step 4. Set aside. 8. Slide the existing door panel out of the doorframe. Side of Attaching the Full Overlay
ページ11に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator Typical Door Panel Pivot Post Wood Panel Wood Panel Top Hinge Plate Top (5/8" Longer than Existing Top Hinge Plate) Pivot Plate x #10 5/8" x #8-32 1/2" Round Head Screw Flat Head Screw Seven Required Three Places Plastic Spacer Top Pivot Plate Seven Required Figure 22 Door Panel 5. Remove the existing bottom pivot plate and replace Figure 24 with the Full Overlay pivot plate (see Figure 23). 3. Install the pivot post into the new Replacement Bottom Hinge
ページ12に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator 5 Adjust Door Checking Door Alignment The unit’s door is aligned at the factory before shipment. Slotted However, its alignment could have been disturbed during Mounting Notch Holes shipment or during door panel installation. IMPORTANT Properly aligned, the door should be 1/8" below the top of the unit’s cabinet, NOT flush with the top (see Figure 26). Raise Lower Outside Outside Door Edge Door Edge Figure 28 1/8" 3. See Figure 28. If the top far edge of th
ページ13に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator 2. Locate the compression fitting and ferrule packed with 6Prepare Plumbing the unit. Slide the compression fitting and ferrule over the 1/4-inch OD water supply line. Do not use thread CAUTION sealing compound or tape. Using two wrenches, tighten the compression fitting on the supply line (see Plumbing installation must observe all state and local Figure 31). codes. All water connections MUST BE made by a licensed/ 3. Carefully bend the water supply lin
ページ14に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator 7 Prepare Power Supply 8 Level the Unit Electrical Specifications Leveling Information CAUTION IMPORTANT It is extremely important that the unit is level. If it is not Electrical installation must observe all state and local level, the ice mold will not fill evenly. codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a 1. Use a level to check the qualified electrician. levelness of the ice maker
ページ15に含まれる内容の要旨
™ CO2075FF — Ice Maker/Refrigerator Door Shelves 9 Install the Unit 1. First pull shelf up at a 45° angle, then straight out Installation of the CO2075FF (see Figure 37). Notch 1. Open the water supply valve in the main water source. 2. Choose new location and line up on bosses. First 2. Make sure the cycle selector switch is in the OFF push straight in, then (middle) position (see Figure 38). down at a 45° angle. 3. Plug in the power cord. Boss 4. Gently push the unit into position. Be ca
ページ16に含まれる内容の要旨
OFF ON OFF ON ™ CO2075FF — Ice Maker/Refrigerator About Settings 10 Start-Up for the First Time No adjustments should be necessary at this time. For information about Adjusting the Temperature Control Initial Start-Up and Adjusting the Cube Size, see the User Manual. Once installation and leveling is complete, the unit is Start-Up Troubleshooting ready for initial start-up and operation. The ON/OFF switch is located in the front grille (see Figure 38). Problem Q: Unit does not appear to tur
ページ17に含まれる内容の要旨
™ Who to Call Service Information If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code. For more than four decades, U-Line has distinguished itself as the leader in built-in underco
