ページ1に含まれる内容の要旨
Hoshizaki America, Inc.
Hoshizaki
Self-Contained Cuber
Models
AM-50BAE
AM-50BAE-DS
AM-50BAE-AD
AM-50BAE-ADDS
INSTRUCTION MANUAL
“A Superior Degree
of Reliability”
www.hoshizaki.com
Issued: 3-10-2006
Revised: 7-1-2011
ページ2に含まれる内容の要旨
IMPORTANT Only qualified service technicians should install, service, or maintain the icemaker. No installation, service, or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual. Likewise, the owner/ manager should not proceed to operate the icemaker until the installer has instructed them on its proper operation. Failure to install, operate, and maintain the equipment in accordance with this manual may adversely affect safety, performance, compo
ページ3に含まれる内容の要旨
IMPORTANT This manual should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that may be necessary. CONTENTS Important Safety Information ..............................................................................................
ページ4に含まれる内容の要旨
Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit. IMPORTANT Indicates important information about the use and care of the unit. WARNING This icemaker should be destined only to the use for which it has been e
ページ5に含まれる内容の要旨
I. Specifications A. Construction Top Panel Ice Making Mechanism Bin Control Thermostat Bulb Scoop Holder Slope Magnet Catch Front Panel Control Switch Door Power Cord Louver 5
ページ6に含まれる内容の要旨
B. Electrical Data HOSHIZAKI ICE MAKER MODEL NUMBER AM-50BAE SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 AMPERES 3.4 AMPS DESIGN PRESSURE HI-240PSI LO-120PSI REFRIGERANT 134a 4.2 OZ. MOTOR-COMPRESSOR THERMALLY PROTECTED APPROVED FOR OUTDOOR USE Hoshizaki America, Inc. Peachtree City, GA www.hoshizaki.com For certification marks, see the nameplate in the storage bin. Note: Only the "MODEL NUMBER" is replaced for AM-50BAE-DS, AM-50BAE-AD, and AM-50BAE-ADDS. The nameplate provides electrical
ページ7に含まれる内容の要旨
C. Dimensions/Connections 1. AM-50BAE 7 Units: mm [in.]
ページ8に含まれる内容の要旨
2. AM-50BAE-DS 8 Units: mm [in.]
ページ9に含まれる内容の要旨
3. AM-50BAE-AD 9 Units: mm [in.]
ページ10に含まれる内容の要旨
4. AM-50BAE-ADDS 10 Units: mm [in.]
ページ11に含まれる内容の要旨
II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable national, state, and local codes and regulations. 2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. A. Checks Before Installation • Visually inspect the exterior of the shipping container and immediately report any damage to the carrier. Upon opening the containe
ページ12に含まれる内容の要旨
2. Built-In Installation Site CAUTION 1. Do not let the weight of the counter rest on the icemaker. 2. Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service. Installation Space Model Height Width Depth AM-50BAE 34" (864 mm) minimum AM-50BAE-DS 15" (381 mm) minimum 24" (610 mm) minimum AM-50BAE-AD 32" (814 mm) minimum AM-50BAE-ADDS Between Two Cabinets Between a Cabinet and the End of a Counter AM-50BAE
ページ13に含まれる内容の要旨
C. Door 1. AM-50BAE, AM-50BAE-AD a) Hinge Reversal If you would like to reverse the door hinges, follow the steps below. Otherwise, skip to section "II.D. Setup." 1) While maintaining a hold on the door, remove the hinge stop pin from hinge (B). Pull out the bottom of the door slightly and gently remove the door from hinge (A). See Fig. 1. Hinge (B) Hinge (A) Fig. 1 Hinge Stop Pin 2) Remove the 2 screws securing the top panel, then lift it off. See Fig. 2. Screws Top Panel Fig. 2 3) Remove hi
ページ14に含まれる内容の要旨
4) Remove hinge (B) from the right side of the unit and the 2 filler screws from the left side. Attach the 2 filler screws to the right side and attach hinge (B) to the left side. See Fig. 4. 5) Rotate the top panel 180° from its previous position. This brings the notch that was previously in the right rear to the left front. See Fig. 5. Hook the rear part of the panel on the body, then secure the front with the 2 screws removed in step 2. Top Panel Screws Notch Hinge (B) Filler Screws Fig
ページ15に含まれる内容の要旨
2. AM-50BAE-DS, AM-50BAE-ADDS a) Overlay Panel Fabrication and Attachment IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag. Overlay Panel Parts No. Description Part Number Qty. 1 Threaded Wood Insert 4A4004-01 6 2 T2 Screw 4×8 SS 7P32-0408 3 3 Pan Head Screw M4×25 SS 7C12-0425 4 4 Truss Head Screw M4×8 SS 7C32-0408 2 5 Canoe Clip 4A0
ページ16に含まれる内容の要旨
(2) Overlay Panel Specification Use the specification that applies to your icemaker (AM-50BAE-DS or AM-50BAE-ADDS) and the directions that follow to prepare your overlay panel. (a) AM-50BAE-DS ( ) ( ) ( ) ( ) AM-50BAE-DS Overlay Panel Specification Overlay Panel Height 29 17/32" (750 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum 16 ( ) ( ) ( ) ( ) ( ) ( )
ページ17に含まれる内容の要旨
(b) AM-50BAE-ADDS ) ( ) ( ( ) ) ( AM-50BAE-ADDS Overlay Panel Specification Overlay Panel Height 27 9/16" (700 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum 17 ( ) ( ) ( ) ( ) ( ) ) (
ページ18に含まれる内容の要旨
(3) Fabrication of Overlay Panel Fabricate the overlay panel as outlined in the applicable specification on the previous pages and the instructions below. 1) Rout a channel at the bottom of the overlay panel to the proper dimensions. See "(C) Routed Area" in the specification diagram and Fig. 8. 2) Drill six 1/4" diameter (hardwood may require slightly larger diameter) holes 3/8" (10 mm) deep in the locations designated. See "(A) Threaded Inserts" and "(B) Threaded Inserts" in the specifica
ページ19に含まれる内容の要旨
6) If you would like to reverse the door hinges, do the following: a) Contact your local distributor to purchase Hoshizaki Kit HS-0229. The kit contains "hinge (A)-left." b) Remove the 2 screws securing the top panel, then lift it off. See Fig. 11. c) Remove hinge (A)-right and the bracket from the right side of the unit. Set aside hinge (A)-right; it is not needed. Remove the top brace from the left side. Fasten hinge (A)-left and the bracket to the left side and the top brace to the right
ページ20に含まれる内容の要旨
7) Remove the bushings from hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 16. 8) Remove the gasket from the door. See Fig. 17. Bushing Gasket Hinge Fig. 17 Fig. 16 9) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided. See Fig. 18. CAUTION Ensure that the back surface of overlay panel is flat before attaching. 10) Mark the centerpoint of the hinge (C1) and hinge (C2) holes that extend over the overlay panel. See Fig. 19. H
