ページ1に含まれる内容の要旨
GE Consumer & Industrial
REFRIGERATORS REF 11-07
DUAL EVAPORATOR SIDE-BY-SIDE REFRIGERATORS
Service Bulletin
SERIAL NUMBERS AG - ZM
ICE BALL KIT
NOVEMBER 2007
WR49X10180 (DOMESTIC 120V)
WR49X10175 (INTERNATIONAL 220V)
FRESH FOOD ICE BALL
Dual Evaporator models, by design, create a high Models Affected: PSF26P, PSS26P,
PSW26P, PSF26R, PSW26R, PCF23P,
humidity environment in the fresh food section.
PSC23P, PSH23P, PSW23P, PCF23R,
Although this design improves the preservation of
PSW23R, PC
ページ2に含まれる内容の要旨
GE Consumer & Industrial Appliances Installation Instructions WR49X10180 Kit–Domestic WR49X10175 Kit–International TOOLS AND KIT CONTENTS: BEFORE YOU BEGIN MATERIALS • AC foil heater assembly Read these instructions completely and NEEDED: • Wire ties (3) carefully. • Crimp style wire connectors (3) • Phillips screwdriver • Aluminum tape – 1-1/4" • Flathead screwdriver IMPORTANT – Observe all governing codes and • White vinyl tape – 1-1/2" • 5/16" hex head ordinances. • Jumper harness nut-d
ページ3に含まれる内容の要旨
C O L D ES T Step 1 Step 4 Remove the bottom three bins and lower shelf in the Apply a liberal bead of RTV along the space between the fresh food compartment. Remove any ice inside the custom cool cover and the left sidewall (Figure 3). fresh food side of the unit. Check under the quick chill Smooth to ensure a clean appearance. assembly. Clean and dry the area, as well as the sump. Step 2 Remove the beverage center duct cover and the evaporator line cover. Remove the fresh food evaporator co
ページ4に含まれる内容の要旨
Step 7 Step 10 Apply aluminum tape to Replace evaporator tube cover. Move evaporator cover the front of the heater back into position and replace screws. Remove the cold assembly. Starting back water reservoir plastic cover. Position the reservoir coils under the Quick Chill as clear of the right front DC grommet as possible assembly and coming (Figure 8). up the front of the heater assembly about 2.5” (Figure 6). Keep the tape as close to the left side fresh food wall as possible. Figu
ページ5に含まれる内容の要旨
Step 12 Step 14 RTV around the underside of the grommet lip (Figure Route the heater assembly wire down through the 10). Insert grommet into hole. Ensure it is pressed installed grommet. Fill inside of grommet around harness completely in, until the base of the grommet lip touches with RTV to prevent air leaks (Figure 12). the fresh food floor surface. Clear excess RTV for clean appearance. Figure 10 Step 13 Figure 12 Use a wire tie to attach the heater wire to the AC harness (right rear ha
ページ6に含まれる内容の要旨
Step 18 Step 20 Use the bell/crimp style wire connectors to connect the Apply power back to unit and ensure both unit and heater wiring to the jumper harness (Figure 14). heater are operational. Listen for compressor and feel heater with back of hand. Heater surface will be slightly warmer than surrounding left wall surface. Go back and ensure that heater assembly is directly touching the left sidewall. Heater may have shifted during wire routing. Step 21 Replace cover on machine compartme
ページ7に含まれる内容の要旨
™ ClimateKeeper 2 dual evaporator technology Temperature and humidity control – Two separate climates – no air crossover – higher humidity in fresh food – fewer defrost cycles – no taste transfer SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE GE Consumer & Industrial General Electric Company © 2007 General Electric Company Louisville, Kentucky 40225 Dwg. No. 225D1974P003 Pub. No. 31-46511 ge.com ND 07G-2330
