ページ1に含まれる内容の要旨
!
" #
$
ADULT/HEMI REMOVABLE ARM
SAVE THESE INSTRUCTIONS
WHEELCHAIR
NOTE: Check all parts for shipping damage before using.
In case of damage, DO NOT use the equipment. Contact
Seat Upholstery
the Dealer/Carrier for further instructions.
Seat Guides
(REAR) and
SAFETY SUMMARY
Tension Springs
The following recommenda
ページ2に含まれる内容の要旨
Screw Screw B B (2) Spacers (2) (2) Spacers (2) Solid Seat Solid Seat X-Brace X-Brace (1) Spacer A (1) Spacer A Screw A* (1) Spacer (1) A Seat Rails (1) Spacer (1) ADULT REMOVABLE ARM ADULT/HEMI PERMANENT WHEELCHAIR (REAR) ARM WHEELCHAIR (REAR) Screw B (2) Spacers (2) Solid Seat A (1) Spacer X-Brace SPACER LENGTH A = 31/32-inch B = 7/16-inch Screw Screw *NOTE: These are the original Spacer (1)* *Spacer (1) spacers and remain on the chair *Spacer (1) in their current location. Screw Screw NOTE: B
ページ3に含まれる内容の要旨
8. Remove both X-Braces from the solid seat (FIGURE 3). Mounting Screws 9. Remove the 5/16-18 x 1-inch bolt and the 5/16-18 Seat Upholstery locknut that secure the two (2) halves of one (1) X- Brace together. Leave the other X-Brace intact (FIGURE 3). REAR Solid Seat X-Brace 5/16-18 x Seat Rails 1-inch Bolt FIGURE 4 - X-BRACE INSTALLATION 12. Replace the tension spring and the seat guide into 5/16-18 the seat rails (FIGURE 1). Nut Solid Seat NOTE: For Permanent Arm Wheelchairs replace seat Moun
ページ4に含まれる内容の要旨
Solid Seat Ordered Off Chair (FIGURE 6) Top View 1. Remove wheelchair arms. 2. Close chair. 3. Remove the ten (10) mounting screws securing the seat upholsteryto the seat rails. Front of Seat 4. Remove the two (2) X-brace pivot screws and lock- nuts from X-brace. 5. Lift one (1) seat rail UP until the two (2) seat guides Spacers are clear of the guide tubes. 6. Remove the end cap, rear seat guide and EXISTING Seat Rails spacer. Discard EXISTING spacer. 7. Repeat STEPS 5-6 on remaining seat rail.
ページ5に含まれる内容の要旨
DETAIL "A" STEPS 1-6 Tap Screws Seat Rails X-Brace Pivot Screw Seat Upholstery Seat Guide Seat Guide X-Brace Pivot Screw Guide Tube Front Solid FrontSolid Seat Seat Braces Braces (Rotated Locknuts (Facing Down Upward For For Shipping) Installation) X-Brace Guide Tube Solid Seat STEPS 7-14 Braces Tap Screws Solid Seat Tap Screws Locknut Bolt Bolt End Cap Seat Short Rail Locknut Spacer Long Spacer Solid Seat Seat Braces RIGHT SIDE OF Guides Long WHEELCHAIR Mounting Scews LEFT SIDE OF Long Solid Se
ページ6に含まれる内容の要旨
6. Perform one of the following: INSTALLING THE SOLID SEAT - A. Spring loaded seat guide: Remove the rear seat TRACER EX ONLY (FIGURE 7) guide and tension spring from the seat rail. NOTE: Refer to the GENERAL WARNINGS in the B. Plastic seat guide: Firmly grasp the plastic seat SAFETY SUMMARY of this Instruction Sheet. guide and pull to remove from the seat rail. NOTE: Right and Left sides of the wheelchair are de- 7. Repeat STEPS 5-6 on remaining seat rail. termined from the occupants position.
ページ7に含まれる内容の要旨
DETAIL "A" Rear Seat Guide (Spring Loaded Tap Screws Seat Rails Seat Guide) Tension Seat Upholstery Spring Locknut Seat Rails NOTE: Spring Seat Guides loaded seat guide Front Solid Guide Tubes FrontSolid Seat shown. Seat Braces Braces (Rotated (Facing Down Upward For X-Brace For Shipping) Installation) X-Brace Pivot Screw STEPS 1-7 RIGHT SIDE OF STEPS 8-16 Solid Seat Rear Seat WHEELCHAIR Brace Guide Tension Tap Spring Screws Seat Solid Seat Rail Short Locknut Solid Spacers Seat Medium Spacer Bol
ページ8に含まれる内容の要旨
%& ' & ! "
# $% &
'() #*
+ ,, - ./ / 01-2
3 / + 4 .---. .4 .44-4 5 /. -/ - 4 - 1 6 7 8
