ページ1に含まれる内容の要旨
!"# $% &# $
NOTE: Check all parts for shipping damage. In case of dam-
1. Secure the frame to the floor with the suction cups or by
age, DO NOT use. Contact your Dealer for further instruction.
standing on the frame base during removal of the seat.
2. Press the UP button on the pendant to raise the
SAFETY SUMMARY
seat all the way up (DETAIL "A").
The following rec
ページ2に含まれる内容の要旨
Removing the Frame from the Bathtub WARNING (FIGURE 2) ALWAYS remove the bath lift from the bath- tub BEFORE performing this procedure. WARNING Otherwise - injury or damage may occur. ALWAYS lower the bath lift frame to the 1. Remove the bath lift frame from the bathtub, if not lowest position BEFORE performing this already done. Refer to REMOVING THE FRAME procedure. Otherwise, the bath lift frame FROM THE BATHTUB in this instruction sheet. may tip during installation resulting in in- jury and/
ページ3に含まれる内容の要旨
Spade Connector Wires STEPS 1 - 2 Connection to Motor Shroud RED YELLOW (+) Wire BLACK Spade Spade Connector Connector Battery Mounting Connector Screws (Nuts NOT SHOWN) Pendant Cable Nut Mounting BLUE (-) Bracket Wire Flared End Mounting Screws YELLOW (+) Wire DETAIL "A" STEP 3 LOOSEN FIGURE 4 - REMOVING THE MOTOR SHROUD Flat Screw - RELEASING THE CABLES (DO NOT REMOVE) BLUE (-) Removing the Battery Connector (FIGURE 5) Bare Wire 1. Remove the two (2) mounting screws and nuts Insulated Wire Mot
ページ4に含まれる内容の要旨
Installing the Battery Connector (FIGURE 7) Mounting REAR CAUTION Screws The BLUE (-) and YELLOW (+) wires MUST BLUE and be installed properly, otherwise, serious YELLOW damage to the electrical system of the Battery bath lift may occur. Connector Motor Wires 1. Position the BLUE (-) wire through the FRONT hole Shroud and the YELLOW (+) wire through the REAR hole as shown in DETAIL "D" of FIGURE 7. Spade FRONT 2. If necessary, loosen, but do not remove the two Connector (2) flat screws in the ba
ページ5に含まれる内容の要旨
DETAIL "D" - STEP 1 1. Connect the spade connector wires to the motor in the following manner: REAR of FRONT of Motor A. BLACK spade connector wire to lower spade. Motor Shroud Shroud B. RED spade connector wire to upper spade. CAUTION FRONT DO NOT secure the pendant cable be- Yellow (+) Wire Hole yond the middle of the cable (measur- ing from the current limit device to the pendant), otherwise damage to the cable may result. . 2. Secure the pendant cable and the spade connec- REAR Hole Blue (-)
ページ6に含まれる内容の要旨
DO NOT Secure Here STEP 2 Spade Connector Wire Wrap Current Mounting Screw STEPS 2-3 Limit Device Mounting Secure Here Bracket Pendant STEPS 1 - 3 Pendant Cable BLACK Spade RED Spade Connector Wire Connector (STEP 1) Motor Shroud STEPS 4-6 Wire Upper To Current Limit Washer (STEP 1) Spade Device Machine Self-locking Screw Screws Secure Pendant Cable and Spade Nut Connector Wire Wrap Together Washer (STEP 2) Mounting Bracket Mounting Mounting Screws Holes Lower Spade Pendant Motor FIGURE 8 - INS
ページ7に含まれる内容の要旨
STEP 1 STEP 2 SIDE VIEW - STEPS 5A & 6 Down PULL UP Up TO Front of the Pendant Bathtub REMOVE PRESS DOWN ON (fixture end) Motor SUCTION CUP Shroud Back of Suction the Cup Bathtub Loop Battery Pack DETAIL "G" Frame STEP 5C Suction Position of Line Cup on Side Flap Entry/Exit Rubber Pad Side Flap Seat Side Flap Hinge FRONT VIEW - STEPS 5C-5D Side Flaps Seat Bathtub Inside Edge of Bathtub Suction Cups Frame and Pads Flat PROPER POSITIONING OF on Bottom of ENTRY/EXIT SIDE FLAP bathtub FIGURE 9 - I
ページ8に含まれる内容の要旨
LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state. Invacare warrants its product to be free from defects in materials and workmanship for one (1) year for the original purchaser. If within such warranty p
