ページ1に含まれる内容の要旨
User's manual
XPB88-LS
Twin-tub Washing Machine with Pump
Contents
Before using
Names of the parts.............the 2nd cover
Safety precautions ...............................1
Installation and adjustment ..................3
Introduction of the major functions .......5
Using process
Preparation before washing ................6
The musts in washing .........................7
Usage of the detergent .......................8
Washing sequence ..............................9
Disposal after was
ページ2に含まれる内容の要旨
Before Using Before Using Names of the parts Buzzer Water-filling entrance Outer cover of the spin tub Water inlet selector handle Inner cover of the spin tub Water selector Spin timer Wash timer Spin tub frame Control panel Overflow filter Spin tub Water level adjusting lever Cabinet Lint filter(Installed by user) Power cord Valve cover Pulsator Wash tub Drain hose Wash tub cover Base frame Meaning and description of the symbols Accessories Contents marked with th
ページ3に含まれる内容の要旨
Before Using Before Using Safety precautions Please insert the power cord into special recep- Be sure to pull the plug off when there's tacle with rated voltage.Be sure to use single power failure, or the machine is being -phase three pins receptacle.The earthing ter- moved, cleaned or when it is idle. minal of the receptacle must be earthed reliably. If possible,please adopt electric leakage protector. Earth If the power cord is bad, to avoid risk it is required to replace it by the
ページ4に含まれる内容の要旨
Safety precautions Before Using Before Using Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the machine by yourself. rotation is slow. Take special care of the children. Do not put any hot or heavy items Do not wash laundries with volatile ( such as the kettle with hot water ) materials (such as thinner, petrol etc.). on the washing machine. Handicapped or children without
ページ5に含まれる内容の要旨
Before Using Installation and adjustment Before Using Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Usage of the drain hose The drainage shall be smooth with the drain hose. 1.The height of the drain hose shall be less than 1.2m , or the drainage will not be smooth enough and cause incomplete drainage. <1.2m 2.Do not step on or press the drain h
ページ6に含まれる内容の要旨
Before Using Before Using How to change the direction of the drain hoses Back Figure 1 indicates the ex factory installation position of the drain hose. Soft item Front Extend the drain hose from the side of spin tub Figure 1 Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. Take off the drain hose from the cabinet. Take the hose out of the fixing groove. (See to Figure 2). Soft item Figure 2 Embed the drain hose into the groo
ページ7に含まれる内容の要旨
Using process Using process Introduction of the major functions The machine has good comprehensive performance, and nice appearance. It adopts complete enclosed base frame and low-noise motor, and thus reduces the working noise significantly. We can guarantee that the purchase of this machine will bring you a clean world without disturbing your quiet life. Foam-removing spinning during high-efficiency rinsing Foam-removing Use the foam-removing spinning to Spin spinning
ページ8に含まれる内容の要旨
Preparation before washing Using process Using process Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put the drain hose up to suitable position. 4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally. Pay attention to f
ページ9に含まれる内容の要旨
The musts in washing Using process Using process The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity. The thickness ,size , type of the cloth will influence the actual washing capacity. It is suitable to put in reasonable amount of laundries and the laundries can be turn
ページ10に含まれる内容の要旨
Usage of the detergent Using process Using process How to use the whitener Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Avoid using whitener on laundries with color or pattern as they are prone to lose color. The whitener shall not touch the laundries directly. Refer to the user's manual for the usage and quantity of the whitener. For powder whitener, please dissolve it before using. How to use the washing powder Di
ページ11に含まれる内容の要旨
Washing sequence Using process Using process Water-filling selector handle Overfilling sign Wash timer Wash selector Water-filling entrance Buzzer Spin timer (To set to below 2 minute, (Strong current, (The buzzer will ring when (to set to below 1 minute, first set to 5 minute then standard current) the washing finishes) first set to 2 minute then turn it back. it can increase turn it back. it can increase the service life of the timer). the service life of the timer). OFF OFF STRONG
ページ12に含まれる内容の要旨
Using process Using process Midway spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Gland Push Push The laundries Proper Proper No gland are slanting (2) Close the inner and outer cover of the spin tub. Outer cover of The spin tub Inner cover of (3) Spin for 1-2 minutes. The spin tub 3.Run the foam-removing spinning. (1) Open the outer cover of the spin tub. (
ページ13に含まれる内容の要旨
Using process Using process Rinsing Rinse with water-filing OVERFILL 1.Put the laundries into the wash tub. Select suitable current according to the laundries. If you find water flo- wing out here,please 2.Adjust the water level twist the water tap to Set the water level with water level adjusting limit the water filling. lever according to the laundries quantity. Then fill suitable water continuously. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing.
ページ14に含まれる内容の要旨
Using process Using process Spinning Selection of the spin time list 3 1. Put the laundries into the spin tub evenly and smoothly. Spin time Laundries (minutes) Bed sheet or 2. Press the gland in the tub properly. About 4~5 blanket Close the inner and outer cover of the spin tub. Underwear About 2~4 (knitwear) Swear About 1~2 3. Spin (chemical fiber) Select suitable spin time according Blending thin to the laundries, and do spinning. Within 1 minute laundries Duri
ページ15に含まれる内容の要旨
Disposal after washing Using process Using process After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing. It must be cleaned in time after each using. 1. Take off the lint filter Put hand at the indicated position. Push down to take it off. (
ページ16に含まれる内容の要旨
Using process Using process Cleaning the overflow filter 2. Take off the corrugation pipe. Dismantle the upper part of the Water level corrugation pipe inside the adjusting lever Corrugation overflow filter ( as indicated in Pipe Figure 1). 3. Cleaning the overflow filter Figure 1 Clean the lint around the filter and flush with tap water. 4. Install the overflow filter. Hook (1).Install the corrugation pipe. (2).Insert the mounting plate at
ページ17に含まれる内容の要旨
Trouble-shooting Answers to question If the laundries fall to the outer side of the spin tub If the laundries fall to the outer side of the spin tub, please take them out immediately. 1.Dismantle As indicated in the figure, push the point marked with " " to pull the spin tub frame to oblique Spin tub frame upwards to dismantle it. 2.Install After install the back edge of the spin tub frame to proper position, push the four points marked with " " by force to reset it. Spin tub Pleas
ページ18に含まれる内容の要旨
Trouble-shooting Answers to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomena The reason Is there power failure? The machine does not act
ページ19に含まれる内容の要旨
Packing list User's manual One Water inlet hose One Water-filling jointer One One Gland Lint filter One Twin-tub washing machine One
ページ20に含まれる内容の要旨
Specification Type Twin-tub washing machine with pump Model XPB88-LS Power source Rated voltage 220V~,Rated frequency 50Hz Water level Water quantity about Maximum/43L Medium/36L Minimum/30L Wash 380 Spin 180 Rated input power W 8.0 Rated washing capacity kg L740 W428 H936 Dimension(mm) New current Wash pattern 27 Weight kg 0.02MPa~0.2MPa Injection pressure
