ページ1に含まれる内容の要旨
WASHER INSTALLATION INSTRUCTIONS
Table of Contents
WASHER SAFETY............................................ 1
INSTALLATION REQUIREMENTS ................. 2
Tools and Parts ............................................. 2
Location Requirements................................. 3
Drain System................................................. 3
Electrical Requirements ................................ 4
INSTALLATION INSTRUCTIONS ................... 4
Before You Start...................................
ページ2に含まれる内容の要旨
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Alternate Parts The parts supplied are in the washer basket. Your installation may require additional parts. For ordering information, please refer to the toll-free phone numbers on the Tools needed for connecting the drain hose and water front page of the Washer User Instructions. inlet hoses: If You Have: You Will Need to Buy: Pliers that open to Flashlight (optional) 3.95 cm
ページ3に含まれる内容の要旨
Location Requirements Drain System Selecting the proper location for your washer improves The washer can be installed using the standpipe drain system performance and minimizes noise and possible washer “walk.” (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See Your washer can be installed in a basement, laundry room, closet, “Tools and Parts.” or recessed area. See “Drain System.” IMPORTANT: Do not install or st
ページ4に含まれる内容の要旨
Electrical Requirements Do not earth to a gas pipe. WARNING Check with a qualified electrician if you are not sure the washer is properly earthed. Do not have a fuse in the neutral or earth circuit. EARTHING INSTRUCTIONS For an earthed, cord-connected washer: This washer must be earthed. In the event of a malfunction Electrical Shock Hazard or breakdown, earthing will reduce the risk of electrical Electrically earth this appliance. shock by providing a path of least resistance for elec
ページ5に含まれる内容の要旨
4. Pull yellow shipping strap firmly, until both ends are completely removed from washer. Laundry tub drain or standpipe drain Connecting the drain hose form to the corrugated drain hose C 5. Check that the two (2) cotter pins were removed with the shipping strap. AB A. Place end of drain hose form around hose at drain hose relief. Squeeze the latch of the drain hose form until it snaps into place. B. Place the other end of the drain hose form around one of the remaining drain hose rel
ページ6に含まれる内容の要旨
3. Using pliers, tighten the couplings with an additional 4. Using pliers, tighten the couplings with an additional two-thirds turn. two-thirds turn. NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result. Tighten the couplings with an additional two-thirds turn. NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result. 5. Attach the cold water hose to the top inlet valve. 6. Screw on coupling by hand until it i
ページ7に含まれる内容の要旨
Level the Washer Properly leveling your washer avoids excessive noise and vibration. Install the Front Leveling Feet Steps in Final Location 1. Prop up the front of the washer about 10.2 cm (4") with a 1. Slide the washer to its final location. wood block or similar object. The block needs to support the 2. Tilt the washer forward until the rear of the washer is at least weight of the washer. 10.2 cm (4") off the floor. You may hear the self-adjusting rear feet click into place. Lower the w
ページ8に含まれる内容の要旨
Complete Installation 1. Check the electrical requirements. Be sure that you have the 7. Check for leaks around faucets and inlet hoses. correct electrical supply and the recommended earthing method. See “Electrical Requirements.” WARNING 2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 3. Check that you have all of your tools. 4. Check that the yellow shipping strap was completely removed from the lower back of th
