ページ1に含まれる内容の要旨
E
V
O
T
S
C
S
O
WONDERWOOD
E
M
T
OWNERS MANUAL
HOW TO ORDER REPAIR PARTS
Model 2941
This manual will help you to obtain efficient, dependable service
from the heater, and enable you to order repair parts correctly.
WONDERWOOD
THERMOSTAT CONTROLLED WOOD BURNING CIRCULATOR
Keep this manual in a safe place for future reference.
When writing, always give the full model number which is on the
nameplate attached to the inside of the cabinet door of the
*ASSEMBLY
heater.
*INSTALLATION
*OPERATION
When o
ページ2に含まれる内容の要旨
TOOLS AND MATERIAL NEEDED F36 BLOWER KIT TOOLS MATERIALS Pencil Chimney Connection- 6" Dia. Black 6 Foot Folding rule or tape Steel (24 Ga. minimum): Straight or An Optional Blower kit is available for the 2941 Wonderwood Tin Snips corrugated elbow (as required)* automatic wood burning circulator heater. If this kit is not available Drill, hand or electric 1/2" Sheet Metal Screws where you have purchased this Wonderwood heater, you can Drill bit, 1/8" dia. 6" Inside Diameter Underwrite
ページ3に含まれる内容の要旨
or masonry) must be tall enough to provide 11.DISPOSAL OF ASHES- Ashes should be NOTE: sufficient draft and safe exit of smoke and placed in a metal container with a tight fitting combustion products. Please refer to Page lid. Keep the closed container on a non- DURING OPENING AND CLOSING OF THE FEED AND ASH DOORS 5. combustible floor or on the ground, well OF THIS HEATER, IT MAY SEEM THAT THE FIT OF THE DOOR IS 4. Be sure that your Chimney is safely con away from all combustible materials. Keep
ページ4に含まれる内容の要旨
heater or chimney connector. The 1 inch air space provides free air circulation. It is essential that REPAIR PARTS LIST - MODEL 2941 (SEE PAGE 18) there be openings at the top and bottom of these clearance reducers so cool air can enter at the AUTOMATIC WOOD BURNING CIRCULATOR bottom and hot air exit at the top. It is the "chimney effect" whereby when the air in the space is heated, it rises exiting from the top and being replaced by cooler air at the bottom, that makes these Key No. Descri
ページ5に含まれる内容の要旨
REPAIR PARTS AUTOMATIC WOOD BURNING CIRCULATOR HEATER 5 MODEL 2941 - INTERIOR 4 32 3 1 24 13 12 23 14 18 29 11 17 26 9 15 19 7 30 31 17 30 31 20 6 16 28 8 16 22 21 25 22 20 2 27 21 10 of which is apparent: The chimney CHIMNEY CONNECTION provides a means for exhausting smoke and flue gases resulting from combustion Two basic types of chimneys are ap- of the fuel. Secondarily, though, the proved for use with solid fuel: Factory- chimney provides "Draft" which allows built and masonry. Factory-bui
ページ6に含まれる内容の要旨
FIG. 6A - Thru-The-Wall Installation REPAIR PARTS AUTOMATIC WOOD BURNING CIRCULATOR HEATER NON-COMBUSTIBLE MODEL NUMBER 2941 WALL (SEE PAGE 16) THIMBLE COLLAR PIPE DAMPER REPAIR PARTS LIST KEY NO. PART NO. DESCRIPTION QTY. BAROMETRIC DRAFT CONTROL 1 89062 Cabinet Door Knob 1 (OPTIONAL) 2 83005 Screw (10-24 x 1/2) FL 1 CLASS A UL 103HT FLOOR PROTECTOR 3 83033 Screw (8-32 x 1/4) PH,TR,HD,Z 1 CHIMNEY KIT INCLUDING WALL THIMBLE. 4 83093 Spring Latch 1 5 83244 Kep Nut (10-24) 1 6 67968 Cabinet Door
ページ7に含まれる内容の要旨
WONDERWOOD 13 14 12 11 16 8 17 7 15 18 19 3 21 9 1 2 10 6 5 4 REPAIR PARTS AUTOMATIC WOOD BURNING CIRCULATOR HEATER MODEL 2941 - EXTERIOR VENTING INTO A FIREPLACE (Not recommended) Many people may wish to convert an Many prefabricated fireplaces fall into existing fireplace to heater use. Usually, the "zero-clearance fireplace" category. safe connection of stovepipe to a ma- This is a factory metal fireplace with sonry chimney requires more effort than multi-layered construction. It is d
ページ8に含まれる内容の要旨
SERVICE HINTS FIREPLACE INSTALLATION Do not expect a heater to draw. It is the 4. If the chimney is too cool, water will chimney that creates the draft. Smoke condense in the chimney and run back Connection of the stovepipe directly into Install the stovepipe as far as possible spillage into the house or excessive into the stove. Creosote formation will the existing masonry chimney over the into the thimble, but not past the inside build-up of water or creosote in the be rapid and may block the
ページ9に含まれる内容の要旨
When considering a masonry chimney, solid fuel appliance must not be joined round tiles are preferable to square or to a chimney flue which is connected to CABINET DOOR KNOB ASSEMBLY rectangular, as round tiles have much another appliance burning other fuels. better airflow characteristics and are far The door knob is mounted inside of the cabinet door to facilitate easier to clean. Unfortunately, most If your chimney has a typically oversized shipping and must be reversed for proper usage. Nor
ページ10に含まれる内容の要旨
WONDERWOOD D WONDERWOO RULES FOR CONNECTOR PIPE INSTALLATION OPERATING INSTRUC- 1. The crimped end of the stovepipe fits 5. Seal each connector pipe joint with TIONS CAUTION: BUILD A FIRE ON THE inside the heater flue collar. Install ad- furnace cement. Also seal the pipe at INTEGRAL GRATE THAT IS PRO- ditional pipe and elbow with the the chimney. FUEL VIDED WITH THE HEATER. CRIMPED END TOWARD THE Hardwood, 18" to 23" should be split HEATER. This will allow any CAUTION: STORING OF WOOD 6. Use
