ページ1に含まれる内容の要旨
CONVERSION WIRING DIAGRAMS
FOR BC7000L1000
The diagrams and instructions contained in this booklet are for converting the following model
programmers to BC7000 Microcomputer Based Burner Control System.
TABLE OF CONTENTS
Page
Section l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...2
Fireye C, D, and E-Series
Section II . . . . . . .
ページ2に含まれる内容の要旨
SECTION I FIREYE C, D, E-SERIES CONTROL 120 V ONLY DIRECTIONS: 1. Disconnect all power to programmer. 2. Remove old programmer from subbase (trade-in to Honeywell Authorized Flame Safeguard Distributor). 3. Mark all wires on subbase; i.e., wires connected to terminal “D” should be marked “D.” Disconnect wires as they are marked. 4. Remove old subbase. 5. Mount Q520A subbase. 6. Connect wires to subbase per attached cross reference. Pay close attention to footnotes. For example: To convert a Fire
ページ3に含まれる内容の要旨
FIREYE 70D10/26CF6-5022/26 CU6-5065 EP160/EP161/EP170 TO BC7000L/PM720L2004 or 1030 E1214A
ページ4に含まれる内容の要旨
FIREYE 24CJ5 - 5010/5011/3010/3011 25CU6 5062/5063/RS-2E 70D30/26CF6 5020/5021/1010/1011 EP380/EP381/EP390 TO BC7000L/PM720M2002 E1215B
ページ5に含まれる内容の要旨
FIREYE 24CJ5 5015 70D20/26CF6 5023/25 CU65055 BC7000L/PM720G2005 TO EP260/EP261/EP270 E1216E
ページ6に含まれる内容の要旨
SECTION II FIREYE P-SERIES CONTROLS 120 V ONLY DIRECTIONS: Disconnect all power to programmer. 1. 2. Remove old programmer from subbase (trade-in to Honeywell Authorized Flame Safeguard Distributor). 3. Mark all wires on subbase; i.e., wires connected to terminal “D” should be marked “D.” Disconnect wires as they are marked. 4. Remove old subbase. 5. Mount Q520A subbase. 6. Connect wires to subbase per attached cross reference. Pay close attention to footnotes. For example: To convert a Fireye 2
ページ7に含まれる内容の要旨
FIREYE 26RJ8 1016, 1016T TO BC7000L + PM720G2005 26RJ8 1012, 1012T, 6012, 6012T E1221A
ページ8に含まれる内容の要旨
FIREYE 25RLJ84580 TO BC700L + PM720L1030 E1693
ページ9に含まれる内容の要旨
FIREYE 25RU8 6560, 6570,6580 BC7000L + PM720L1030 26RJ8 6060, 6070,6080, 6160 TO E1217B
ページ10に含まれる内容の要旨
FIREYE 29RF5 1001, 1009, 6009 TO BC7000L + PM720G2013 E1218A
ページ11に含まれる内容の要旨
26RJ8 6058, 6066, 6068 BC7000L + PM720G2005 TO 25RU8 6558, 6566 E1219A
ページ12に含まれる内容の要旨
FIREYE 26RJ8 1002, 1003, 1008, 1011, 1018, 6008, 6018 29RF5 1000, 1002, 1005, 1015, 1104 29RF5 6015 TO BC7000L + PM720G2005 E1220A
ページ13に含まれる内容の要旨
SECTION Ill HONEYWELL R4126, R4127, R4181 CONTROLS 120 V ONLY DIRECTIONS: 1. Disconnect all power to programmer. 2. Remove old programmer from subbase (trade-in to Honeywell Authorized Flame Safeguard Distributor). 3. Mark all wires on subbase; i.e., wires connected to terminal “D” should be marked “D.” Disconnect wires as they are marked. 4. Remove old subbase. 5. Mount Q520A subbase. 6. Connect wires to subbase per attached cross reference. Pay close attention to footnotes. For example: To con
ページ14に含まれる内容の要旨
R4126A1172, 1180,1198 TO BC7000L + PM720L2004 E1222A
ページ15に含まれる内容の要旨
R4126A1008, 1016, 1024, 1032, 1040, 1057, 1081, 1149 R4126B1006, 1014, 1022 TO BC7000L + PM720G2005 E1223A
ページ16に含まれる内容の要旨
R4126A1073,1164 TO BC7000L + PM720L2004 E1224A
ページ17に含まれる内容の要旨
BC7000L + PM720G2005 R4127A1155 AND R4127A1197 TO E1753
ページ18に含まれる内容の要旨
R4127 (ALL MODELS) EXCEPT R4127A1171, R4127A1155, R4127A1197, R4127B1039, AND R4127B1047 TO BC7000L + PM720G E1225A
ページ19に含まれる内容の要旨
R4127A1171/R4127B1039/R4127B1047 TO BC7000L+PM720G2005 E1724A
ページ20に含まれる内容の要旨
R4181A1000, R4181A1026 TO BC7000L + PM720G2005 E1226A
