ページ1に含まれる内容の要旨
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW TREADMILL!
ページ2に含まれる内容の要旨
Table of Contents Product Registration…………………………………………………………………………. 2 Important Safety Instructions………………………………………………………………… 3 Important Electrical Information………………………………………………………………4 Important Operation Instructions……………………………………………………………..5 Assembly instructions………………………………………………………………………….6 Folding & Transport Instructions…………..………………………………………………….12 Operation of Your New Treadmill……………………………………………………………. 13 Programmable Features……………………………………………………………………….16 Target Heart Rate
ページ3に含まれる内容の要旨
CONGRATULATIONS ON YOUR NEW TREADMILL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality treadmill from Spirit Manufacturing, Inc. Your new treadmill was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local dealership wher
ページ4に含まれる内容の要旨
Important Safety Instructions WARNING - Read all instructions before using this appliance. DANGER - To reduce the risk of electric shock disconnect your Spirit treadmill from the electrical outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the treadmill on a flat level surface with access to a 120-volt, 20-amp grounded outlet. DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE GROUNDED P
ページ5に含まれる内容の要旨
fatigue. Remove tether cord after use to prevent unauthorized treadmill operation. SAVE THESE INSTRUCTIONS - THINK SAFETY! Important Electrical Information WARNING! ● NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power cord away from any moving part of the treadmill including the elevation mechanism and transport wheels. ● NEVER remove any cover without first disconnecting AC power. ● If voltage varies by ten percent (10%) or more
ページ6に含まれる内容の要旨
● NEVER operate this treadmill without reading and completely understanding the results of any operational change you request from the computer. ● Understand that changes in speed and incline do not occur immediately. Set your desired speed on the computer console and release the adjustment key. The computer will obey the command gradually. ● NEVER use your treadmill during an electrical storm. Surges may occur in your household power supply that could damage treadmill components
ページ7に含まれる内容の要旨
XT200. / XT 600 / XT 800 6
ページ8に含まれる内容の要旨
Assembly Instructions (XT200 / XT600) XT200. / XT 600 / XT 800 7
ページ9に含まれる内容の要旨
ASSEMBLY PACK CHECK LIST (XT200 /XT600) (8 pcs) 5/16" x 15m/m Button Head Socket Screw (4 pcs) 5/16" x 2" Button Head Socket Screw (4 pcs) 8 x 23 x 1.5T Curve Washer (2 pcs) 5/16" x 2-3/4" Button Head Socket Screw (2 pcs) 5/16" x 1-1/2" Button Head Socket Screw (4 pcs) 8 x 23 x 1.5T Flat Washer (6 pcs) 3.5x38 m/m Self Tapping Screw (1pc) Safety Key (1 pc) Deck / Belt Lubricant (1 pc) Combination M5 Allen Wrench & Screwdriver (1 pc) M6 Allen Wrench Assembly (XT200 /XT600) Unpac
ページ10に含まれる内容の要旨
STEP 2 1. Mount the L&R Handle bars onto Handle bar mounting plates at the top of the upright tubes with 4pcs of 5/16” x 2” Button Head Socket Screw and 4pcs of curved washer. NOTE: The L&R handle bars are different. The Right handle bar has two wires and the switches on the handle bar say “Fast and Slow” while the Left handle bar switch says “Up and Down”. STEP 3 1. Install the L & R inside console end caps onto the ends of the 1-1/4” X 2-3/8” console mounting tube. Ensure the end c
ページ11に含まれる内容の要旨
Assembly Instructions (XT800) XT200. / XT 600 / XT 800 10
ページ12に含まれる内容の要旨
ASSEMBLY PACK CHECK LIST (XT800) (2 pcs) 3/8" x 2" Button Head Socket Screw (10 pcs) 5/16" x 15m/m Button Head Socket Screw (2 pcs) 3/8" x 2T Spring Washer (4 pcs) 5/16" x 2" Button Head Socket Screw (2 pcs) 5/16" x 2-3/4" Hex Head Screw (2 pcs) 5/16" x 1-1/2" Button Head Socket Screw (4 pcs) 8 x 23 x 1.5T Flat Washer (8 pcs) 8 x 23 x 1.5T Curve Washer (4 pcs) 5/16" x 1-3/4" Button Head Socket Screw (4 pcs) M5 Iron Plate Nut (2 pcs) 5x16 m/m Tapping Screw (6 pcs) 5 x 16 m/m Tappin
ページ13に含まれる内容の要旨
STEP 2 1. Install the L & R inside console end caps onto the ends of the 1-1/4” X 2-3/8” console mounting tube. Ensure the end caps are oriented correctly and facing the correct direction (see diagram). Also ensure that the wiring is fed through the end caps. 2. Place the console onto the L & R mounting brackets at the top of the upright tubes. Then install and hand tighten the 2 pcs. of 5/16” x 2-3/4” Hex Head Screw and flat washers through the hole in the top of the 1-1/4” X 2-3/8” co
ページ14に含まれる内容の要旨
XT200 / XT600 Folding Instructions Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired position. ■ To Fold The Treadmill: Make certain the treadmill is at minimum incline. Lift the treadmill running deck until it is secured by the locking telescoping tube assembly in center back of base. ■ To Unfold The Treadmill: Apply slight forwar
ページ15に含まれる内容の要旨
XT200. / XT 600 / XT 800 14
