ページ1に含まれる内容の要旨
www.proform.com
Model No. PFTL06711.0
Serial No. USERʼS MANUAL
Write the serial number in the space
above for reference.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT CON-
TACT THE STORE; please contact
Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.pr
ページ2に含まれる内容の要旨
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 PART IDENTIFICATION CHAR
ページ3に含まれる内容の要旨
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and in- structions in this manual and all warnings on your treadmill before using your treadmill. ICON as- sumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. Before beginning any exercise program, con- carrying 15 or more amps. No other appliance sult your physician. This is especially impor- should be on the same circuit. Do not use
ページ4に含まれる内容の要旨
20. Never leave the treadmill unattended while it 24. Inspect and properly tighten all parts of the is running. Always remove the key, unplug treadmill regularly. the power cord, and press the power switch into the off position when the treadmill is not 25. DANGER: Always unplug the power in use. (See the drawing on page 5 for the lo- cord immediately after use, before cleaning the cation of the power switch.) treadmill, and before performing the mainte- nance and adjustment procedures described
ページ5に含まれる内容の要旨
BEFORE YOU BEGIN ® Thank you for selecting the revolutionary PROFORM ing this manual, please see the front cover of this man- 610 RT treadmill. The 610 RT treadmill offers an im- ual. To help us assist you, please note the product pressive selection of features designed to make your model number and serial number before contacting us. workouts at home more enjoyable and effective. And The model number and the location of the serial num- when youʼre not exercising, the unique treadmill can be ber
ページ6に含まれる内容の要旨
PART IDENTIFICATION CHART Use the drawings below to identify small parts used for assembly. The number in parentheses below each draw- ing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat- tached. Extra hardware may be included. 1/4" Star 5/16" Star 3/8" Nut (10)–4 3/8" Star Washer (12)–2 Washer (9)–8 Base Foot Spacer Washer
ページ7に含まれる内容の要旨
ASSEMBLY • To hire a service technician to assemble this • To identify small parts, see page 6. product in your home, call 1-800-445-2480. • Assembly requires the following tools: • Assembly requires two persons. the included hex keys • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing one adjustable wrench materials until you finish all assembly steps. one Phillips screwdriver • The underside of the walking belt is coated with high-performance lub
ページ8に含まれる内容の要旨
2. Attach a Wheel (95) to the Base (94) with a 3/8" 2 x 3" Bolt (67), two Wheel Spacers (96), and a 67 3/8" Nut (10). Do not overtighten the Nut; the 96 Wheel must turn freely. 94 95 10 96 3. Identify the Right Upright (83), which is marked 3 with a “Right” sticker. Have a second person 83 hold the Right Upright near the Base (94). See the inset drawing. Tie the wire tie in the 85 Right Upright (83) securely around the end of the Upright Wire (85). Then, pull the other end Wire Tie of the wire t
ページ9に含まれる内容の要旨
4. Insert a 3/8" x 5 1/2" Screw (7), a 3/8" x 4 3 3/4" Screw (97), and a 3/8" x 2 1/4" Screw 7 31 (31) with three 3/8" Star Washers (11) into the 83 Right Upright (83) in the locations shown. 97 11 Hold the Right Upright (83) against the Base 11 (94). Be careful not to pinch the Upright Wire (85). Partially tighten the 3/8" x 5 1/2" Screw (7) 85 and the 3/8" x 3 3/4" Screw (97) until the heads of the Screws touch the Right Upright; do not 94 fully tighten the Screws yet. Then, partially tighten
ページ10に含まれる内容の要旨
6. Attach a Wheel (95) to the Base (94) with a 3/8" 6 x 3" Bolt (67), two Wheel Spacers (96), and a 3/8" Nut (10). Do not overtighten the Nut; the 84 Wheel must turn freely. Attach the Base Cover (84) to the Base (94) with four #8 x 1/2" Screws (1). Be careful not to overtighten the Screws. 1 67 96 94 10 95 96 1 1 7. Attach the Frame Crossbar (107) to the Frame 7 (55) with two 1/4" x 1 3/4" Screws (91). With the help of a second person, tip the tread- mill so that the Base (94) is flat on the fl
ページ11に含まれる内容の要旨
8. Set the console assembly face down on a soft 8 surface to avoid scratching the console. 8 Console 79 Wire Identify the Right Handrail (79). Hold the Right 12 4 Handrail near the console assembly. Route the console wire through the large holes in the top and bottom of the Right Handrail. 9 Set the Right Handrail (79) on the Console Frame (81). Start a 1/4" x 1/2" Screw (8) with a Console 1/4" Star Washer (12) into the Right Handrail. Assembly Then, start two 5/16" x 1 1/2" Bolts (4) with two 5
ページ12に含まれる内容の要旨
10. Set the console assembly on the Left and Right 10 Console Uprights (82, 83). Be careful not to pinch any Assembly wires. Insert the excess wire into the Right Upright. Start two 5/16" x 3/4" Screws (5) with two 5/16" Star Washers (9) into the Right Upright (83). 4 Then start a 5/16" x 1 1/2" Bolt (4) into the Right Upright. Repeat this step on the left side of the tread- mill. Then, firmly tighten all four 5/16" x 3/4" 5 4 5 Screws (5) and both 5/16" x 1 1/2" Bolts (4). 9 9 82 83 11. See ste
ページ13に含まれる内容の要旨
12. Press the Left Outside Upright Cover (87) and 12 82 the Left Inside Upright Cover (90) around the Left Upright (82). Attach the Upright Covers with 87 a #8 x 1/2" Screw (1). Attach the Right Outside Upright Cover (86) and the Right Inside Upright Cover (88) in the same way. 83 1 1 90 86 88 13. Raise the Frame (55) to the position shown. 13 Have a second person hold the Frame until 107 this step is completed. Orient the Storage Latch (51) so that the large barrel and the latch knob are orient
ページ14に含まれる内容の要旨
OPERATION AND ADJUSTMENT HOW TO PLUG IN THE POWER CORD This product is for use on a nominal 120-volt circuit (see drawing 1). A temporary adapter may be used to connect the surge suppressor to a 2-pole receptacle if a properly-grounded outlet is not available (see DANGER: Improper connection drawing 2). of the equipment-grounding conductor in- creases the risk of electric shock. Check with a qualified electrician or serviceman if you 1 Grounded Outlet Box are unsure whether the product is proper
ページ15に含まれる内容の要旨
CONSOLE DIAGRAM Audio Jack FEATURES OF THE CONSOLE You can even listen to your favorite workout music or audio books with the consoleʼs stereo sound system. The treadmill console offers an impressive array of features designed to make your workouts more effec- To turn on the power, see page 16. To use the man- tive and enjoyable. When you use the manual mode of ual mode, see page 16. To use a preset workout, the console, you can change the speed and incline of see page 18. To use the iFit traini
ページ16に含まれる内容の要旨
HOW TO TURN ON THE POWER HOW TO USE THE MANUAL MODE IMPORTANT: If the treadmill has been exposed to 1. Insert the key into the console. cold temperatures, allow it to warm to room tem- perature before turning on the power. If you do not See HOW TO TURN ON THE POWER at the left. do this, you may damage the console displays or other electrical components. 2. Select the manual mode. Plug in the power cord (see Each time the key is in- page 14). Next, locate the serted, the main menu power switch on
ページ17に含まれる内容の要旨
4. Change the incline of the treadmill as desired. 6. Measure your heart rate if desired. To change the incline of the treadmill, press the Before using Incline increase or decrease button, or one of the 1 the handgrip Step Incline buttons numbered 0 to 10. Each time heart rate you press one of the buttons, the incline will gradu- monitor, re- ally change until it reaches the selected incline move the setting. sheets of plas- tic from the Contacts 5. Select a display mode and monitor your metal
ページ18に含まれる内容の要旨
HOW TO USE A PRESET WORKOUT is programmed for Current Segment the next segment, 1. Insert the key into the console. the speed and/or incline setting will See HOW TO TURN ON THE POWER on page 16. flash in the dis- plays for a few 2. Select a preset workout. seconds and the treadmill will automatically adjust to the new speed and incline settings. If you have selected a workout or the iFit Training mode, press the Menu button to return to the main The workout will continue in this way until the la
ページ19に含まれる内容の要旨
HOW TO USE THE IFIT TRAINING MODE HOW TO USE THE STEREO SOUND SYSTEM The optional iFit Live module allows your treadmill to To play music or audio books through the consoleʼs communicate with your wireless network and unlocks stereo speakers, you must connect your MP3 player, exciting new features. For example, you can download CD player, or other personal audio player to the con- personalized workouts, create your own workouts, sole. Locate the audio wire and plug it into the audio track your w
ページ20に含まれる内容の要旨
THE INFORMATION MODE The console features a display demo mode, designed to be used if the treadmill is displayed in a store. While The console features an information mode that keeps the demo mode is turned on, the console will function track of the total distance that the walking belt has normally when you plug in the power cord, press the moved and the total number of hours that the treadmill power switch into the reset position, and insert the key has been used. The information mode also allo
