ページ1に含まれる内容の要旨
INTEGRITY SERIES TREADMILLS
CST, CLST & 97TI ASSEMBLY INSTRUCTIONS
M051-00K58-C379
ページ2に含まれる内容の要旨
Congratulations... and welcome to the world of The following Component Lists and the step-by-step assembly procedures have been assembled to make the set-up of this treadmill as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the treadmill. IMPORTANT SAFETY INSTRUCTIONS ! l DO NOT position the rear of the treadmill any closer than 6.5 feet (2 meters) to the nearest obstruction. It is recommended that t
ページ3に含まれる内容の要旨
COMPONENT LIST # Part Description Qty. # Part Description Qty. 1 Left Upright 1 2 Right upright 1 3 Handlebar (left and right) 2 4 Ergo™ Front Crossbar 1 5 Left inside handlebar shroud 1 6 Right inside handlebar shroud 1 7 Left outside handlebar shroud 1 8 Right outside handlebar shroud 1 Lower upright cover (left and right) 9 Display console 1 10 2 0017-00101-1265 11 Left accessory tray 1 12 Right accessory tray 1 13 Handlebar cap 2 14 Rear frame endcap 2 Handlebar shroud screw Endcap / Upright
ページ4に含まれる内容の要旨
HARDWARE SCREW GROMMET (#18) HANDLEBAR SHROUD SCREW (#15) FRONT CROSSBAR NUT (#22) ENDCAP / UPRIGHT COVER SCREW (#16) UPRIGHT WASHER (#24) LINECORD CLIP (#23) DISPLAY CONSOLE / HANDLEBAR SUPPORT SCREW (#17) FRONT CROSSBAR SCREW (#19) UPRIGHT MOUNTING BOLT (#20) ACCESSORY TRAY SCREW (#21) 3
ページ5に含まれる内容の要旨
IMPORTANT! DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT. NE JETEZ PAS LE KIT D'EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION. IMPORTANT! Check the belt edge under the treadmill to verify the belt does not interfere with lifespring brackets and the belt is properly set within the belt guides. 1. Remove the four SCRE
ページ6に含まれる内容の要旨
6. Locate both HANDLEBARS (3). Slide one HANDLEBAR GROMMET (27) over each HANDLEBAR. The groove of the HANDLEBAR GROMMET should face outward. M 6 26 5 7. w ith the bend of one HANDLEBAR (3) directed to the outside of the treadmill, insert the HANDLEBAR into the RIGHT UPRIGHT HANDLEBAR 26 BRACKET (L) as shown. Be sure the handlebar mounting holes are aligned. Repeat for the left side HANDLEBAR. 19 L 22 4 8. Locate the ERGO™ FRONT CROSSBAR (4) and position the ERGO O FRONT CROSSBAR with the plas
ページ7に含まれる内容の要旨
12. Slide the LEFT INSIDE HANDLEBAR SHROUD (5) near the LEFT UPRIGHT HANDLEBAR BRACKET (N). Position the HANDLEBAR GROMMET (27) at the end of the LEFT INSIDE HANDLEBAR SHROUD. Install the HANDLEBAR GROMMET onto the inside edge of the LEFT INSIDE HANDLEBAR SHROUD as shown. Locate and position the LEFT OUTSIDE HANDLEBAR SHROUD (7) to match the LEFT INSIDE HANDLEBAR SHROUD. Install the remaining portion of the HANDLEBAR GROMMET onto the R LEFT OUTSIDE HANDLEBAR SHROUD as it is positioned to ma
ページ8に含まれる内容の要旨
16. Locate the LEFT ACCESSORY TRAY (11). Carefully slide the tray into the top of the LEFT UPRIGHT (1) as shown until fully seated. Secure the accessory tray to the LEFT TOP MOUNTING PLATE (H) using four SCREWS (21). Repeat the procedure for the RIGHT ACCESSORY TRAY (12) and RIGHT TOP MOUNTING PLATE (J). 17. Tighten all UPRIGHT BOLTS securely. 18. Replace the MOTOR COVER (E) and secure the MOTOR COVER to the FRAME (C) using the four previously removed SCREWS (D). Tighten the SCREWS securely.
ページ9に含まれる内容の要旨
IMPORTANT! CHECK THE BELT EDGE UNDER THE TREADMILL TO v ERIFY THE BELT DOES NOT INTERFERE w ITH LIFE- SPRING BRACKETS AND THE BELT IS PROPERLY SET w ITHIN THE BELT GUIDES. PHYSICAL DIMENSIONS: PHYSICAL DIMENSIONS INCHES (CM) WEIGHT LBS (KG) SET UP HEIGHT MODEL LOW VOLTAGE HIGH VOLTAGE INCHES CM LENGTH WIDTH HEIGHT 403 413 83 37 63.5 CLST 11 28 (183 kg) (187 kg) (211 cm) (94 cm) (161 cm) 431 440 83 37 65.5 97Ti 13 33 (195 kg) (200 kg) (211 cm) (94 cm) (166 cm) 410 420 83 37 63.5 CST 11 28 (186 kg
