ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Your Local Agent/Dealer Your Local Agent/Dealer 9-52 Ashihara-cho, 9-52 Ashihara-cho, Nishinomi Nishinomiy ya, Ja a, Jap pan an Tele Telep phone : hone : 0798-65-2111 0798-65-2111 Telefax : Telefax : 0798-65-4200 0798-65-4200 F FIRST EDITION : IRST EDITION : OCT. OCT. 1998 1998 A All ri ll rig ghts reserved. hts reserved. Printed in Japan Printed in Japan L L :: JUL. JUL. 10,2003 10,2003 PUB.No. PUB.No. IME-34690-L IME-34690-L *00080839301* *00080839301* *00080839301* *00080839301* ( ( TENI TE
ページ3に含まれる内容の要旨
SAFETY INSTRUCTIONS WARNING WARNING WARNING WARNING Do not open the equipment Radio Frequency Radiation unless totally familiar with Hazard electrical circuits and service manual. The radar scanner emits electromagnetic radio frequency (RF) energy which can be Only qualified personnel ELECTRICAL harmful, particularly to your eyes. Never should work inside the SHOCK look directly into the scanner aperture from HAZARD equipment. a close distance while the radar is in oper- a
ページ4に含まれる内容の要旨
WARNING CAUTION Be sure that the power supply is Ground the equipment to compatible with the voltage rating of prevent electrical shock and the equipment. mutual interference. Connection of an incorrect power supply Observe the following compass safe can cause fire or equipment damage. The distances to prevent deviation of a voltage rating of the equipment appears magnetic compass: on the label above the power connector. Standard Steering Use only the specified power cable. compass compass D
ページ5に含まれる内容の要旨
TABLE OF CONTENTS EQUIPMENT LISTS ............................................................................ iv SYSTEM CONFIGURATION............................................................... vi MOUNTING 1.1 Scanner Unit ............................................................................................................. 1-1 1.2 Display Unit ............................................................................................................... 1-7 1.3 Power Supply Unit ....
ページ6に含まれる内容の要旨
EQUIPMENT LISTS Standard Supply Ne ame T. yp Cy ode NoQs t Remark S- N30AF 1r Radiato S- N36AF R- SB-0026 1r Antenna chassis, with or without deice Scanner UnitR- SB-0031 R- SB-0088 R- SB-0089 Antenna chassis for HSC R- SB-0090 D4 isplay UnitR- DP-12 1 P- SU-004-70-23-S 3φ,C 220/230 VA P- SU-004-80-10-S 3φ,C 380/440 VA Power Supply 1 Unit P- SU-004-70-23-HK 3φ,C 220/230 VA P- SU-004-80-23-HK 3φ, 380/440 VAC SP03-12506 (Display Unit), S0 pare PartsS8 P03-1310 01 00-087-69 SP03-10320 (Power Supply
ページ7に含まれる内容の要旨
Optional Equipment Ne ame T. yp Cy ode NoQs t Remark R0 emote DisplayF– MD-801 1 G2 yro ConverterG0 C-8- 0t 08-446-521r se Separate orde I7 nterswitch R– J- 1 I8 nterswitch R– J- 1 P0 erformance MonitorP– M-5 1 Mandatory for IMO radar 110 V →220 V, 3φ R6 U-569301 00-030-45 for scanner unit 440 V →100 V, 1φ R7 U-180301 00-030-49 for display unit Transformer 220 V →200 V, 3φ R0 U-652201 00-030-41 Unit for scanner unit R8 U-330501 00-030-44 For deicer 440 V →200 V, 3φ R3 U-5466-101 00-030-45 for sc
ページ8に含まれる内容の要旨
For DISPLAY UNIT For SCANNER UNIT SYSTEM CONFIGURATION SCANNER UNIT SN30AF/SN36AF RSB-0026/0031 RSB-0088/0089/0090 (For HSC) IEC 61162-1 (Input/Output) Navigator IEC 61162-1 (Input) Speed Log DISPLAY UNIT ARPA Board RDP-124 Slave Display ARP-26 FMD-8010 POWER SUPPLY Video Plotter RP-26 UNIT PSU-004 220 VAC, 3φ, 60 Hz Gyro Converter 200 VAC, 3φ, 50 Hz Performance GC-8 Monitor 440 VAC, 3φ, 60 Hz 380 VAC, 3φ, 50 Hz PM-50 For HSC 220 VAC, 3φ, 50 Hz 220 VAC, 3φ, 60 Hz Gyrocompass 440 VAC, 3φ, 60 H
ページ9に含まれる内容の要旨
MOUNTING 1.1 Scanner Unit Mounting considerations • The scanner unit is generally installed either on top of the wheelhouse or on the radar mast, on a suitable platform. Locate the scanner unit where there is a good all-round view. • No funnel, mast or derrick should be within the vertical beamwidth of the scan- ner in the bow direction, especially zero degrees ±5°, to prevent blind sectors and false echoes on the radar picture. • It is rarely possible to place the scanner unit where a completel
ページ10に含まれる内容の要旨
Installation precaution for S-band scanner unit If an S-band scanner unit is mounted near the end of a platform to provide suffi- cient rotation clearance for the radiator, the scanner unit, because of its weight, swings up and down by ship’s vibration and rolling, exerting excessive levels of stress at the base of the radiator, which can damage the radiator. To prevent this, relocate the scanner unit, or if relocation is not possible, reinforce the platform. Pole for DF, etc. Remarkable vibrati
ページ11に含まれる内容の要旨
How to lift scanner unit 1. Fix the scanner radiator to the scanner unit chassis. 2. Attach the lifting fixtures and collars as shown in Figure 1-2 and 1-3. . = 3. Position the radiator as shown in Figure 1-3 and arrange the ropes A . 2m . = and B . 1.8m. Lifting fixture Supplied as installation materials. Remove after Collar for fixing installation. Spring washer (M12) Hex bolt (M12X20) Remove lifting fixture, coat threads of hex bolts with silicone grease, and then insert bolts in scanner body
ページ12に含まれる内容の要旨
Scanner unit assembling The scanner radiator and the scanner housing are shipped in separate packages. Assemble them as below. The scanner unit may be assembled before hoisting it to the mounting platform. However, do not lift the scanner unit by the radiator. Scanner unit assembling procedure 1. Screw the guide pins (2 pcs.) in the radiator. 2. Remove the protective cap from the choke guide. 3. Grease O-ring and set it to groove of the choke guide. 4. Place the radiator on the radiator bracket.
ページ13に含まれる内容の要旨
Fastening the scanner unit to the mounting platform See the figure on the next page for scanner unit mounting. 1. Referring to the scanner outline drawing, drill four bolt holes (15 mm dia.) in the radar mast platform or the deck. • The diameter of the mast for fixing the scanner unit platform must be over 15 mm. • The thickness of the scanner unit platform must be over 15 mm. • The reinforcement ribs must be installed diagonally as shown below. Over 15 mm Use two nuts. 250 mm diameter or more,
ページ14に含まれる内容の要旨
Seal washer Corrosion- proof rubber mat Use two nuts. Set corrosion-proof rubber mat, bolt scanner unit to mounting location, and coat exposed hardware with silicone sealant. Hex bolt Flat washer Flat washer Ground wire Spring washer Coat with silicone sealant after Hex nut fastening ground wire. Coat with silicone OR sealant. Ground wire Hex nut Spring washer Flat washer Hex bolt Welding Ground wire Scanner body Arrange ground terminal as close as possible to scanner unit. Ground terminal provi
ページ15に含まれる内容の要旨
1.2 Display Unit Before mounting the display unit If Gyro Converter GC-8 (option) is to be used, install and setup the GYRO CON- VERTER Board before mounting the display unit, because of the difficulty involved in doing it after the display unit is installed. Instructions for installation and setup are in Chapter 4. Mounting considerations When selecting a mounting location, keep in mind the following points: • Select a location where the display unit can be viewed and operated conve- niently an
ページ16に含まれる内容の要旨
4. While one person is holding the mounting base at the sides, pull the handle on the underside of the control head to draw the display unit toward you until you hear a click. CAUTION Use two people to complete this step. The display unit may fall to the deck when it is pulled forward, since the mounting base is not yet fastened to the mounting location. Handle Pull forward Figure 1-8 Display unit 5. This step requires two people to complete.
ページ17に含まれる内容の要旨
Stopper Catch Stay Figure 1-10 Setting catch to hole in stay c) Release hand from stopper. Release stopper; fix stay. Figure 1-11 Stay fixed 6. Fasten the display unit to the mounting location at front fixing holes (2 points) with M10 bolts, nuts and flat washers, using the pipe box spanner (supplied). You cannot fasten the display unit at the rear fixing holes while the monitor is raised. 7. Retract the stay and lower the monitor. 8. Fasten the display unit to the mounting locations at rear fix
ページ18に含まれる内容の要旨
Fixing hole (rear) J106 * Knob *M3x8, 5 pcs. J105
J104 * Slide forward. J103 * * M4x8, 2 pcs. Fixing hole (front) J446 J466 J462 J465 Figure 1-12 How to remove the PTU cover 9. Push the monitor forward until you hear a click. 10.Fix the brackets with the M10 bolts removed at step 2. Console type mounting 1. Make six holes of 15 mm diameter and a cable entrance hole through the deck referring to the outline drawing at end of this manual. 2. Open the front cover. 3. Fix the equipment with M12 bo
ページ19に含まれる内容の要旨
Separate type control head kit (Type: OP03-151, No.: 008-485-530) Ne ame Tyyp Q. tCs odenoRemark CP ableAssy. U1L246SB20P/102 00-140-81210m,03S942 R3ubberFeet S4J-500 0e 00-801-787w/tap M1 onitorFrontCover013-255-136 100-263-340 K1 BFixingPlate013-144-169 100-263-940 H2 andlePlate013-144-163 100-268-041 D3 ustcoverKB013-144-169 100-271-760 S0 crew M34x1 000-881-446 L1 abel 816-003-101 100-236-230 N4 onshipRubber013-144-169 100-271-760 Display unit modification procedure 1. Raise the monitor unit
ページ20に含まれる内容の要旨
4. Unfasten the M4 screw fixing the ground terminal of the connection cable. 5. Push the monitor forward until you hear a click. 6. Unscrew four screws fixing the top cover of the display unit. 7. Remove three clamps fixing the connection cable in the monitor unit. 8. Unfasten four screws fixing the right and left brackets on the control head. 9. Unfasten four screws fixing the right and left covers of the display unit. 10.Unfasten six screws fixing the right and left KB arms. 11.Unfasten three
