ページ1に含まれる内容の要旨
MARINE RADAR/ARPA
FAR-2137S/2837S/2137S-BB
Installation Manual Comply with MSC.192(79)
TABLE OF CONTENTS
3.4 Adjustment Sweep Timing.................... 3-6
SAFETY INSTRUCTIONS....................... i
3.5 Suppressing Main Bang ....................... 3-7
EQUIPMENT LISTS .............................. iii
3.6 Other Settings ...................................... 3-8
SYSTEM CONFIGURATION.................. v
3.7 Dual Radar Display
(non IMO-type only) .......................... 3-16
ページ2に含まれる内容の要旨
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : APR. 2004 All rights reserved. Printed in Japan L : APR. 12, 2011 Pub. No. IME-35210-L (HIMA ) FAR-2137S/BB/2837S *00014868819* *00014868819* **00014868819 00014868819** * 0 0 0 1 4 8 6 8 8 1 9 *
ページ3に含まれる内容の要旨
SAFETY INSTRUCTIONS The operator and installer must read the applicable safety instructions before attempting to install or operate the equipment. Indicates a potentially hazardous situation which, if not avoided, will result in death or serious injury. DANGER Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. WARNING Indicates a potentially hazardous situation which, if not avoided, CAUTION can result in minor or moderate injury.
ページ4に含まれる内容の要旨
CAUTION WARNING Do not open the equipment Observe the following compass safe unless totally familiar with distances to prevent deviation of a electrical circuits and magnetic compass: service manual. Standard Steering compass compass Only qualified personnel ELECTRICAL should work inside the Antenna Unit SHOCK 3.95 m 2.55 m (30 kw) equipment. HAZARD Monitor Unit 1.55 m 1.00 m (MU-201CR) Construct a suitable service platform Monitor Unit 1.85 m 1.20 m (MU-231CR) from w
ページ5に含まれる内容の要旨
EQUIPMENT LISTS Standard Supply Name Type Code No. Qty Remarks SN30AF - 1 Radiator 200 VAC 3 φ 50 Hz, RSB-098 - 220 VAC 3 φ 60 Hz Antenna Chassis 380 VAC 3 φ 50 Hz, Antenna Unit RSB-099 - 1 440 VAC 3 φ 60 Hz RSB-100 - 220 VAC, 3 φ, 50 Hz Antenna Chassis RSB-101 - 220 VAC, 3 φ, 60 Hz for HSC RSB-102 - 440 VAC, 3 φ, 60 Hz Power Supply Unit PSU-007 - 1 MU-201CR For FAR-2137S MU-231CR For FAR-2837S Monitor Unit - 1 MU-190 For FAR-2137S MU-231 For FAR-2837S Processor Unit
ページ6に含まれる内容の要旨
Name Type Code No. Remarks For processor unit, RU-1803 - 440 VAC → 100 VAC For de-icer , 110/115/220/230 VAC RU-3305 - → 100 VAC For RSB-098/099, Transformer Unit RU-5693 - 110 V →220 VAC Not For RSB-098/099, RU-6522 - available 220 V →200 VAC for HSC For RSB-098/099, RU-5466-1 - 440 V →220 VAC Memory Card Interface Unit CU-200-FAR 000-081-568 W/CP03-27430, See chapter 4. External Buzzer OP03-21 000-030-097 Control Unit RCU-016 000-080-299 Remote type, W/FP03-09860 RA
ページ7に含まれる内容の要旨
SYSTEM CONFIGURATION Radiator SN30AF/ ANTENNA UNIT SN36AF Performance Monitor Chassis RSB-098/099 RSB-100/101/102 (for HSC) POWER SUPPLY UNIT PSU-007 RJB-001 ** * MONITOR UNIT MU-201CR or MU-190 (FAR-2137S) MU-231CR or MU-231 (FAR-2837S) CONTROL UNIT *** RCU-014 RU-5693 (Standard) *** or RU-6522 RCU-015 100-230 VAC RJB-001 ** (Trackball) *** RU-5466-1 Control Unit 1) EPFS RCU-016 IEC-61162 Serial Data PROCESSOR UNIT (Navigator) (Remote) (Input/Output) RPU-013 2) SDME IEC-61162 Serial Dat
ページ8に含まれる内容の要旨
About the category sticker This radar meets the requirements in IEC62388 (Marine navigation and radio communication equipment and systems-Shipborne radar-Performance requirements, method of testing and required test results). Check the appropriate box on the sticker which is pre-attached on the processor unit, according to your radar’s specification. Refer to the table shown below to confirm your category. Category Radar Type Antenna rotation speed FAR-2817, FAR-2827, FAR-2837S, FAR-
ページ9に含まれる内容の要旨
1. MOUNTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. 1.1 Antenna Unit Mounting considerations • The antenna unit is generally installed either on top of the wheelhouse, on the radar mast, or on a suitable platform. Locate the antenna unit in an elevated position to permit maximum target visibility. • A
ページ10に含まれる内容の要旨
1. MOUNTING • Install the antenna unit safely away from interfering high-power energy sources and other transmitting radio antenna. • Keep the lower edge of the antenna unit above the safety rail by 500 mm or more. • Two antenna units should be mounted as below: more than 20 more than 1 m • No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in the bow direction, especially zero degrees ±5°, to prevent blind sectors and false echoes on the radar pic
ページ11に含まれる内容の要旨
1. MOUNTING Installation precaution for S-band antenna unit If an S-band antenna unit is mounted near the end of a platform to provide sufficient rotation clearance for the radiator, the antenna unit, because of its weight, swings up and down by ship’s vibration and rolling. This exerts excessive levels of stress at the base of the radiator, which can damage the radiator. To prevent this, relocate the antenna unit, or if relocation is not possible, reinforce the platform. Mast for DF
ページ12に含まれる内容の要旨
1. MOUNTING Antenna unit assembling The antenna radiator and the antenna housing are shipped in separate packages. Assemble them as below. The antenna unit may be assembled before hosting it to the mounting platform. However, do not lift the antenna unit by the radiator. Antenna unit assembling procedure 1. Screw the guide pins (2 pcs.) in the radiator. 2. Remove the protective cap from the choke guide and radiator. 3. Grease O-ring and set it to the groove of the choke guide. 4. Pl
ページ13に含まれる内容の要旨
1. MOUNTING How to lift the antenna unit 1. Fix the antenna radiator to the antenna unit chassis as shown on page 1-4. 2. Attach the lifting fixtures and collars as shown below. 3. Position the radiator as shown below and arrange the ropes A and B. Lifting fixture Supplied as accessories. Remove after installation. Collar for fixing Spring washer Plat washer (M12) x20) Hex bolt (M12 (Torque 63.5Nm) Remove lifting fixture, coat threads of hex bolts with silicone grease, and then insert b
ページ14に含まれる内容の要旨
1. MOUNTING Fastening the antenna unit to the mounting platform See the figure on the next page for antenna unit mounting. 1. Referring to the antenna outline drawing, drill eight fixing holes of 15 mm in diameter in the radar mast platform or the deck. • The diameter of the mast for fixing the antenna unit platform must be over 250 mm. • The thickness of the antenna unit platform must be over 15 mm. • The reinforcement rib must be installed diagonally as shown below. Over 15mm Use t
ページ15に含まれる内容の要旨
1. MOUNTING Seal washer Corrosion proof rubber mat Use two nuts. (Torque 63.5Nm) Ground terminal G1_1/4-A Set corrosion-proof rubber mat, bolt antenna unit to mounting location, and coat exposed hardware with silicone sealant. Hex bolt Flat washer Flat washer Ground wire Spring washer Coat with silicone sealant after Hex nut fastening ground wire. Coat with silicone OR sealant. Ground wire Hex nut Spring washer Flat washer Hex bolt Ground wire Welding Antenna chassis Arrange ground terminal
ページ16に含まれる内容の要旨
1. MOUNTING 1.2 Monitor Unit The monitor unit can be flush mounted in a console panel, or mounted on a desktop using the optional accessories. For MU-190/231, see the applicable Operator’s Manual(s). Note: FAR-2137S-BB has no monitor unit. Prepare a suitable one locally. Recommended monitor: SXGA (1280x1024), aspect ratio 5:4 Mounting considerations When selecting a mounting location, keep in mind the following points: • Select a location where the display unit can be viewed conven
ページ17に含まれる内容の要旨
1. MOUNTING ± 506 1 4-FIXING HOLES ± 1 506 4-φ8 490 FIXING HOLES 534 30 80 Monitor unit MU-201CR (For FAR-2137S) 4-φ8 FIXING HOLES 570 ± 1 4-FIXING HOLES 554 570 ± 1 598 80 30 Monitor unit MU-231CR (For FAR-2837S) Flush mounting of monitor unit Panel hook Panel cover Fixing screw Attaching panel hook and panel cover Note: If you need to remove the monitor unit from the mounting panel, remove the four panel covers with your fingernail and use two panel hooks supplied as accessor
ページ18に含まれる内容の要旨
1. MOUNTING Contents of FP03-09820/09830 Name Type Code No. Qty Remarks Hanger L 03-163-1111 100-305-141 1 Hanger R 03-163-1112 100-305-181 1 03-163-1113 100-305-191 For FAR-2137S Hanger stay 1 03-163-2071 100-305-371 For FAR-2837S Hole plug CP-30-HP-13 000-160-074-10 2 Plastic rivet KB-13 Rivet Black 000-570-276-10 4 Hex. bolt M6x25 000-162-949-10 4 Hex. bolt M10x30 000-162-884-10 2 Spring washer M10 000-864-261 2 Flat washer M10 000-864-131 2 1. Assemble two hangers
ページ19に含まれる内容の要旨
1. MOUNTING The hand grip is optionally available for the desktop mounting monitor unit. Wave washer Rosette washer Screw M6x20 (Torque 7.6Nm) Handle Hood (option) When it is too bright in the daytime, use the optional hood to shade the screen. • For FAR-2137S: FP03-11500 (Code No.: 001-020-090) • For FAR-2837S: FP03-11000 (Code No.: 008-571-680) Contents of hood Name Type Code No. Qty. Remarks Hood (21) FP03-11501 001-020-120 1 For FAR-2137S Hood (23) FP03-11001 008-571-700
ページ20に含まれる内容の要旨
1. MOUNTING 1.3 Power Supply Unit The Power Supply Unit PSU-007 does not contain usual operating controls. Therefore, it can be installed in any recessed place either in vertical or horizontal position. (For the console mount display unit, the PSU-007 can be installed inside the console.) However, select a dry and well-ventilated location and observe the compass safe distance to prevent deviation of a magnetic compass. See page ii. 1. Open the cover of the power supply unit. 2. Fas
