ページ1に含まれる内容の要旨
Disc Grinder
125 mm (5”)
MODEL 9005B
125 mm (5”)
MODEL 9005BZ
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
ページ2に含まれる内容の要旨
SPECIFICATIONS model 9005B 9005BZ No load speed (RPM) 10,000/min 10,000/min Overall length 356 mm (14”) 356 mm (14”) Net weight 3 kg (6.6 lbs) 3 kg (6.6 lbs) Spindle thread 5/8” 5/8” • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serio
ページ3に含まれる内容の要旨
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
ページ4に含まれる内容の要旨
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
ページ5に含まれる内容の要旨
5. Always use safety glasses or goggles. 13. Make sure the wheel is not contacting the Ordinary eye or sun glasses are NOT workpiece before the switch is turned on. safety glasses. 14. Before using the tool on an actual work- 6. Check the wheel carefully for cracks or piece, let it run for a while. Watch for damage before operation. Replace vibration or wobbling that could indicate cracked or damaged wheel immediately. poor installation or a poorly balanced Run the tool (with guard) at no load f
ページ6に含まれる内容の要旨
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001024 Shaft lock CAUTION: 1 Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when install- ing or removing accessories. 1. Shaft lock Switch action CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “
ページ7に含まれる内容の要旨
ASSEMBLY CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 001055 Installing side grip (handle) CAUTION: Always be sure that the side grip is installed securely before operation. Screw the side grip securely on the position of the tool as shown in the figure. 001063 Installing or removing wheel guard CAUTION: When using a depressed center grinding wheel/Multi- 1 disc, wire wheel brush or cut-off wheel, the wheel guard 3 must be fi
ページ8に含まれる内容の要旨
001087 To tighten the lock nut, press the shaft lock firmly so that the 1 spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the wheel, follow the installation procedure in reverse. 2 1. Lock nut wrench 2. Shaft lock 001110 Installing or removing abrasive disc 1 (optional accessory) 2 NOTE: 3 Use sander accessories specified in this manual. These must be purchased separately. Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and
ページ9に含まれる内容の要旨
CAUTION: After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down. 001124 Grinding and sanding operation ALWAYS hold the tool firmly with one hand on rear handle and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of 15˚ about 15 degrees to the workpiece surface. AB During the break-in period with a new wheel, do not w
ページ10に含まれる内容の要旨
001232 Operation with wire wheel brush (optional accessory) 1 CAUTION: • Check operation of wire wheel brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel brush. • Do not use wire wheel brush that is damaged, or which 1. Wire wheel brush is out of balance. Use of damaged wire wheel brush could increase potential for injury from contact with broken wires. • ALWAYS use guard with wire wheel brushes, assuring diameter of wheel fits inside guard. W
ページ11に含まれる内容の要旨
MAINTENANCE CAUTION: 001164 • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or 1 maintenance. The tool and its air vents have to be kept clean. Regularly clean the tool’s air vents or whenever the vents start to 2 become obstructed. 1. Exhaust vent 2. Inhalation vent 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the
ページ12に含まれる内容の要旨
your Makita distributor or factory service center, be sure to obtain and use all necessary fasteners and guards as recommended in this manual. Your failure to do so could result in personal injury to you and others. If you need any assistance for more details regarding these accessories, ask your local Makita service center. 001183 1 2 6 2 10 12 3 7 9 11 3 4 8 13 5 5 9005B/BZ 1Grip 36 2 Wheel guard 3 Inner flange 45 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 5/8-45 6 Rubber pad 115
ページ13に含まれる内容の要旨
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
ページ14に含まれる内容の要旨
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
ページ15に含まれる内容の要旨
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO KENTUCKY NEW MEXICO PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 1215 S. Hurstbourne Parkway 5805 Menaul Blvd. NE 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Louisville, KY 40222 Albuquerque, NM 87110 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (502) 326-3740 (505) 881-4619 (787) 250-8776 ARIZONA CONNECTICUT LOUSIANA NEW YORK TENNESSEE 3707 E. Broadway Rd., Ste. 6 508 Spring St.
ページ16に含まれる内容の要旨
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
