ページ1に含まれる内容の要旨
MODEL SB1044
CUTTING FLUID KIT
Instruction Sheet
PHONE: (360) 734-1540 • www.southbendlathe.com
BIOLOGICAL & POISON
HAZARD!
Use the correct personal
protection equipment
when handling cutting
fluid. Follow federal, state,
and fluid manufacturer
requirements for proper
disposal.
Introduction
Figure 1. Model SB1044.
This cutting fluid kit is for the Model SB1029
Surface Grinding Machine. The system is
designed to pump water-soluble cutting fluid to
Unpacking
minimize grinding wheel w
ページ2に含まれる内容の要旨
SB1029 Mfg. Since 6/10 Model SB1044 INSTRUCTIONS Installation During the installation process of your cutting fluid kit, you'll need the following items: For Power Connection Spash Guard • A power source that meets the minimum circuit requirements for this machine. Trough • A qualified electrician to ensure a safe and code-compliant connection to the power source. Drain Cover For Assembly Chip P ort • Phillips Screwdriver #2 Shield • Cotton Rags and Silicone Sealant • Hex Wrenche
ページ3に含まれる内容の要旨
Mfg. Since 6/10 Model SB1044 INSTRUCTIONS To use the cutting fluid system: Operation 1. Make sure the cutting fluid is properly Only use high quality water-soluble cutting serviced and the tank is filled. fluid in this system. Never attempt to pump straight cutting oils or kerosene. If you do, the 2. Put on the necessary personal protection higher viscosity of the oil will overload the motor, equipment. causing damage, or flammable liquids may ignite. 3. Position the cutting fluid nozzle
ページ4に含まれる内容の要旨
Mfg. Since 6/10 Model SB1044 INSTRUCTIONS Maintenance When you replace the old cutting fluid, take the Leaving the pump running with an empty time to thoroughly clean out both sides of the cutting fluid tank can damage a pump. Shut tank. Make sure to dispose all old fluid according the pump OFF immediately when the fluid to local regulations. Cutting fluid is considered slows or stops coming from the drain hose. hazardous waste by the EPA. Follow all disposal and storage guidelines when
ページ5に含まれる内容の要旨
Mfg. Since 6/10 Model SB1044 INSTRUCTIONS Troubleshooting Symptom Possible Cause Possible Solution Little or no cutting 1. No power; voltage is incorrect. 1. Switch power supply ON/verify machine and pump fluid is being voltages match. pumped. Pump and 2. Blown fuse/tripped circuit breaker 2. Correct the cause of overload, then reset/replace motor may also at main panel. fuse or breaker. vibrate or be noisy. 3. Coolant level is too low, and pump 3. Fill coolant tank with a minimum of four ga
ページ6に含まれる内容の要旨
Mfg. Since 6/10 Model SB1044 INSTRUCTIONS Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section carefully. If you see differences between your machine and what is shown in this section, call Technical Support at (360) 734-1540 for assistance BEFORE making any changes to the wiring on your machine. 1. Shock Hazard: It is extremely dangerous
ページ7に含まれる内容の要旨
AMP AMP Mfg. Since 6/10 Model SB1044 INSTRUCTIONS Model SB1029 Pump Connection Wiring Diagram ! If the pump motor runs in a counterclockwise direction as viewed through the motor shaft sight glass, disconnect machine from power and swap wire positions U1 and V1 on the terminal bar shown below. Fuses 4A 1 R1 T1 1 2 3 3 R1 U V W U1 V1 W1 R S T 4 6 7 0 SB1029 Surface Fuses Grinder 4A GND 1 R1 1 2 3 4 0 U V W R S T U1 V1 W1 1 R1 T1 1 2 3 3 R1 U V W U1 V1 W1 R S T 4 6 7 0 GND 1 2 To Control 1
ページ8に含まれる内容の要旨
Mfg. Since 6/10 Model SB1044 INSTRUCTIONS Parts Diagram Parts List REF PART # DESCRIPTION 24 3 1 PSB1044001 CUTTING FLUID TANK 14 26 17 2 PSB1044002 HINGED TANK COVER 25 2 3 PSB1044003 MOTOR/PUMP 1/8HP 3-PH 220V/440V 4 PSB1044004 FLUID DELVERY HOSE 1/2" X 9ft 12 4 5 PSB1044005 ELBOW FITTING 18 6 PSB1044006 SWIVEL CASTER 26 7 PSB1044007 SPLASH GUARD 1 5 8 PSB1044008 COOLANT TROUGH 10 17 9 PSB1044009 DRAIN PORT 21 10 PBHS09M BUTTON HD CAP SCR M6-1 X 12 23 22 11 PWN01M WING NUT M6-1 12 PSBHS35M BUT
