ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
950W
100MM (4”)
ANGLE GRINDER
MX100MAG
INSTRUCTION MANUAL
1
ページ2に含まれる内容の要旨
Contents Warranty 2 Warranty Power Tools Whilst every effort is made to ensure your complete Introduction 3 satisfaction with this tool, occasionally, due to the mass Environmental protection 3 manufacturing techniques, a tool may not live up to our required level of performance and you may need the Description of symbols 3 assistance of our service department. Specifications 3 This product is warranted for a 2-year period for home domestic use from the date of the original purchase. Safet
ページ3に含まれる内容の要旨
Introduction Description of symbols The rating plate on your tool may show symbols. Your new GMC power tool will more than satisfy These represent important information about the your expectations. It has been manufactured under product or instructions on its use. stringent GMC Quality Standards to meet superior performance criteria. Wear hearing protection. Wear eye protection. You will find your new tool easy and safe to operate, Wear breathing protection. and, with proper care, it
ページ4に含まれる内容の要旨
Personal safety Safety instructions • Stay alert, watch what you are doing and use WARNING. Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, common sense when operating a power tool. Do not use a power tool while you are tired or under the fire and/or serious injury. The term “power tool” in all of the warnings below refers to your mains-operated (corded) power influence of drugs, alcohol, or medication. A moment of inatt
ページ5に含まれる内容の要旨
• Do not use the power tool if the switch does not turn Additional safety rules for angle grinders it on and off. Any power tool that cannot be controlled • Fully unwind cable drum extensions to avoid potential with the switch is dangerous and must be repaired. overheating. • Disconnect the plug from the power source before • When an extension cable is required, you must ensure making any adjustments, changing accessories, or that it has the right ampere rating for your power tool an
ページ6に含まれる内容の要旨
• Always use the side handle and ensure a good grip on Contents of carton the grinder housing with one hand and the handle with The GMC MX100MAG Angle Grinder is supplied with the the other hand before proceeding with any work. following accessories as standard: • Make sure that the disc is not in contact with the work • Pin wrench when you start the grinder. • Side handle • Be careful not to damage the spindle or either of the disc • 100mm metal cutting disc flanges. Damage to these p
ページ7に含まれる内容の要旨
Know your product Before using the angle grinder, familiarise yourself with all the operating features and safety requirements. Use the tool and accessories only for the applications intended. All other applications are expressly ruled out. 1. Motor housing 2 4 5 1 2. Spindle lock button 3. Disc guard 4. Mounting points for the side handle 5. On/off switch 6. Side handle 7. Pin wrench 8. Outer flange 9. Disc 10. Inner flange 11. Quick release guard lever 11 9 3 6 Disc assembly showing flan
ページ8に含まれる内容の要旨
Setting up Operation Multi-position side handle This angle grinder can be used for grinding and cutting steel, stone or ceramic workpieces such as pipe, box Screw the side handle (6) into the section, rectangular, angle iron most suitable mounting port (4) steel bar, house bricks and tiles. (left side or right side) to suit the Do not attempt to grind wood or application. Ensure that the handle a soft metal such as lead. The is fully screwed in place and firm. material will quickly “fi
ページ9に含まれる内容の要旨
WARNING. Avoid flying sparks and ensure they do not hit NOTE. Depending on whether the disc has a flat inner any inflammable materials, as they are very hot and could section or a depressed inner section, proceed as follows. cause personal injury or a fire. 6. For discs with a flat inner WARNING. The disc continues to turn for a few seconds section, screw on the outer even though the switch is turned off. Keep your hands well flange (8) with the protruding away from the moving disc. spigot
ページ10に含まれる内容の要旨
Lubrication The grease in the gearbox will require replacement after extensive use of the tool. Please go to a qualified service agent to perform this service. Power cord maintenance If the supply cord needs replacing, the task must be carried out by the manufacturer, the manufacturer’s agent, or an authorised service centre in order to avoid a safety hazard. Cleaning 1. Keep the tool’s air vents unclogged and clean at all times. 2. Remove dust and dirt regularly. Cleaning is best done
ページ11に含まれる内容の要旨
11
ページ12に含まれる内容の要旨
GMC customer assist If your product needs repairing, replacing, technical service or you simply need help or advice, please contact us on our Customer Assist Line 1300 880 001 (Australia) or 0800 445 721 (New Zealand). For prompt service we suggest you log your service request online at www.gmcservice.com.au. Should you not have access to the Internet, please contact our service department on 1300 880 001 (Australia) or 0800 445 721 (New Zealand). 7am –7pm, 7days a week (AEST). Please n
