ページ1に含まれる内容の要旨
OWNER'S
MANUAL
MODEL NO.
580.751510
®
5 HORSEPOWER
1800 PSi 2.5 GPM
HiGH PRESSURE WASHER
HOURS:
Mort.- Fri. 8 a.m. to 5 p.m
(CST)
o Assembly
CAUTION:
Read and Follow
o Operation
all Safety Rules
° Customer Responsibilities
and Instructions
Before Operating
o Service and Adjustment
This Equipment
° Repair Parts
SEARS, ROEBUCK and CO., Hoffman Estates, IL 60179 U.S.A.
Part No 96596 Revision 3 (6/20195)
ページ2に含まれる内容の要旨
SAFETY RULES TACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, _ AUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CON_ _, ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER. • Always wear eye protection when you use this equipment TRAINING: or when you are in the vicinity where the equipment is in e EngineexhaustgasescontainDEADLYcarbonmonox- use. Ide gas_ This dangerous gas, if breathed in sufficient e Operate the pressure at no more th
ページ3に含まれる内容の要旨
CONGRATULATIONS on your purchase of a Sears Crafts- PRODUCT SPECIFICATIONS man high pressure washer, it has been designed, engi- Pressure Washer Specifications neered and manufactured to give you the best possible dependability and performance. PUMP PRESSURE Adjustable to 1800 psi ....... Should you experience any problem you cannot easily FLOW RATE 2.5 gpm remedy, please contact your nearest Sears Service Cen- DETERGENT MIX Use undiluted detergent ter/Department or call the 1-800 number listed
ページ4に含まれる内容の要旨
TABLE OF CONTENTS CUSTOMER RESPONSIBILITIES .......................... 14-15 SAFETY RULES ............................................................. 2 PRODUCT SPECIFICATIONS ....................................... 3 SERVICE AND ADJUSTMENTS .................................. 16 ACCESSORIES AND ATTACHMENTS ......................... 5 STORAGE .................................................................... 17 CONTENTS OF HARDWARE PACK ............................. 6 TROUBLESHOOTING .........
ページ5に含まれる内容の要旨
ACCESSORIES AND ATTACHMENTS These accessories and attachments were available when the high pressure washer was purchased. They are also available at most Sears retail outlets and service centers, Most Sears stores can order these items for you when you provide the model number of your high pressure washer, Some of these accessories may not apply to your pressure washer° i != i i FLOOR/SIDING ROTATING BRUSH UTILITY BRUSH KIT 18" STAINLESS ELECTRIC TURBO ANGLE EXTENSION STEEL EXTENSION BRUSH KIT K
ページ6に含まれる内容の要旨
CONTENTS OF HARDWARE PACK Parts packed separately in carton Parts Carton l Owners Manual ,_r.__f Gun and Wand Assembly Guide Handle Assembly (packed inflat carton Main Unit (packed in flat carton) Parts packed in Parts Carton High Pressure Hose Motor Oil (2) Wheels (3)Parts Bags Parts Bag contents not Parts Bag contents shown full size (fasteners) shown full size (2) Washers - M8 (2) Axle Pins (2) Support Leg Wire Support Assemblies Parts Bag contents not shown full size (2) Hex Head Capscrews -
ページ7に含まれる内容の要旨
ASSEMBLY Read these instructions and Operator's Manual in its en- HOW TO SET UP YOUR PRESSURE WASHER tirety before you attempt to assemble or operate your new TO INSTALL THE WHEEL KIT high pressure washer. Your high pressure washer has, for the most part, been assembled at the factory, except those Installing the wheel kit requires the tools listed, the guide parts left unassembled. Before you can operate your new handle and items included in the parts carton. high pressure washer, you must asse
ページ8に含まれる内容の要旨
ASSEMBLY connector. Reattach male connector to water inlet and = Using a 5/16" (8mm) wrench, attach wire support to top attach female connector to garden hose. two holes of guide handle with #10 self-drilling screws Unravel highpressure hose, remove plastic cap on end and #10 flat washers (Fig. 3), The hose minder should Q of hose and check other end of |lose to see that threads be to the left and _unholder to the right° Be sure loop are properly covered with teflon tape. If tape is not of suppo
ページ9に含まれる内容の要旨
OPERATION KNOW YOLIR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER. Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustment& Save this manual for future reference. SPARK PLUG PRESSURE REGULATOR CUP FOR WAND ENGINE RUN/STOP GUIDE HANDLE CONTROL STORAGE MUFFLER NOZZLE WIRE SUPPORT ]CLEANER HIGH PRESSURE HOSE CARBURETOR GUN AND WAND ASSEMBL_ DETERGENTPICK UPTUBE
ページ10に含まれる内容の要旨
OPERATION HOW TO USE YOUR WASHER IF YOU HAVE ANY PROBLEMS OPERATING YOUR PRESSURE WASHER. PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1-800-222-3136. STOPPING YOUR PRESSURE WASHER o First, move engine throttle lever to"OFF" position(Fig. 9). OPTIONAL TURBO NOZZLE ADJUSTABLE NOZZLE FIG. 10 FIG, U With the adjustable nozzle you can adjust the spray pattern to be either high pressure or low pressure. You can also adjust the spray so it is concentrated in a stream pattern or OFF, IDLE FAST I l expan
ページ11に含まれる内容の要旨
OPERATION DETERGENT APPUCATION WITH ADJUSTABLE o Hook up water supply (Fig° 16). NOZZLE o Adjust nozzle to select high pressure mode, IMPORTANT: USE SOAPS DESIGNED SPECIFICALLY NOTE: Detergent will not flow when in the high pressure FOR PRESSURE WASHERS. HOUSEHOLD DETER- mode, GENTS COULD DAMAGE THE PUMP. o Start washer and work from the top of the surface to IMPORTANT: YOU MUST ATTACH ALL HOSES BE- the bottom_ FORE YOU START THE ENGINE. STARTING THE EN_ NOTE: The high pressure mode is most effe
ページ12に含まれる内容の要旨
OPERATION GAS NOTE: When adding oil to the engine crankcase in the future, use only high quality detergent oil rated with API WARNING: NEVER FILL FUEL TANK INDOORS. NEVER RLL FUEL TANK WHEN ENGINE IS RUN- service classification SF, SG or SH rated SAE 30 weight° NING OR HOT, DO NOT SMOKE WHEN FILLING Use no special additives. Select the oil's viscosity grade FUEL TANK. according to your expected operating temperature. WARNING: NEVER FILL FUEL TANK COM- colder 32°F warmer PLETELY FULL. FILL TANK T
ページ13に含まれる内容の要旨
OPERATION TO START ENGINE iMPORTANT: DO NOT RUN PUMP WITHOUT THE WATER SUPPLY CONNECTED AND TURNED ON, YOU MUST FOLLOW THIS CAUTION OR THE PUMP WILL BE DAMAGED. = Press trigger on pressure washer wand to relieve high pressure and/or purge the inlet hose of air. • Move throttle control to FAST position (Fig. 19). FIG. 21 NOTE: The engine is equipped with low oil level shutdown system. The engine will not start unless the oil crankcase is filled to proper level. If engine shuts down during opera-
ページ14に含まれる内容の要旨
CUSTOMER RESPONSIBJLITIIES iii MAINTENANCE SCHEDULE FiLL IN DATES AS YOU COMPLETE HOURLY OPERATING INTERVAL REGULAR SERVICE Every25 Every100 Before Hours or After First Hours or SERVICE DATES MAINTENANCE TASK Each Use 50Hours Yearly Yearly PRESSURE WASHER Chock/clean inletfilter and screen xt X Chock high pressurehose. Check detergent hose. X X Check gun and wand for leaks. Chock pump oil. x$ ENGINE Chock oil level. X Change engine oil. _, X_ Serviceair'cleaner. X*_ Replace/clean spark plug. X P
ページ15に含まれる内容の要旨
CUSTOMER RESPONSIBILITY PUMP MAINTENANCE Pump OI1: Change pump oil after first 50 hours of opera- tion, then every 500 hours thereafter° To change pump oil, follows these steps: = Place a proper container beneath the pump. You will only need a small one because capacity is only 5 ounces, = Remove the Oil Drain Plug on bottom of pump and drain oil into the container (Fig_ 22)° FIG. = When engine crankcase is filled to proper level, install and tighten oil fill plug. SERVICE AIR CLEANER Your engin
ページ16に含まれる内容の要旨
CUSTOMER RESPONSiBILITiES CLEAN COOUNG SYSTEM CLEAN OUT CHAFFAND • Clean dirt or chaff from finger 0uard or rotating screen DIRT even] 8 hours to prevent engine damage caused by ovedleating (Fig. 25), = Keep dirt and combustible debris off of muffler area. REPLACE SPARK PLUG Change the spark plug every 100 hou rs of operation or' once each year, whichever comes first, This will help engine to start easier and run better. See pressure washer specifications for the type of spark plug you need. Spa
ページ17に含まれる内容の要旨
STORAGE It is important to prevent gum deposits from forming in AFTER EACH USE essential fuel system parts such as the carburetor, fuel Water should not remain in the unit for long periods of time. filter, fuel hose or tank during storage_ Also, experience Sediments of minerals can deposit on pump parts and indicates that alcohol-blended fuels (called "gasohot" or "freeze" pump action. Follow these procedures after every using ethanol or methanol) can attract moisture which leads use: to separat
ページ18に含まれる内容の要旨
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Pump has following problems: t. Nozzle in low pressure mode. t. Pull nozzle backwardfor high failure to produce pressure, erratic pressuremode° pressure, chattering, loss of pressure, 2. Low regulator pressure 2= Adjust regulator to desired setting. low water volume. 3 Water inlet is bIocked, 3,, Clear'inlet 4o Inadequate water supply 4o Provide adequate water flow. 5. 5. Straighten inlet hose, patch leak,. Inlet hose is kinked or leaking 6. 6. Check and
ページ19に含まれる内容の要旨
REPAIR PARTS CRAFTSMAN 1800 PSI HIGH PRESSURE WASHER 580.751510 Gu,BARREL I I° i, 40 6 3F z j °G" 34 D_ESCRIPTION DESCRIPTION ITEM PART NO, PART NO. ITEM 5/8" Lock Washer (2 req,) 5 hp Briggs & Straiten Engine (1 req,) 22 22246 1 95998 Jam Nut (2 mq.) Pump (1 req,) 23 25391 2 87628 Wheel Axle (2 mq,) Brass Water Hose Connector (t req,) 24 93728 3 89647 M8d 25 x 20mm Capscrew (6 req,) Quick-connect, Female (1 req,) 25 39253 96016 4 M8-1.25 Flange Nut (12 mqo) Quick-connect, Male (1 req.) 26 52858
ページ20に含まれる内容の要旨
CRAFTSMAN 1800 PSi HIGH PRESSURE WASHER 580.751510 REPAIR PARTS BRIGGS & STRATTON 4-CYCLE ENGINE 133212-0159-01 346 36 35 40 357 41 9 7 17 8 10 33 34 ! 26 27 615 616 45 592 ,f' 0 X_ _"( _ _ J'-&_ 1_o_9 LABEL K_TI \%. __, wu _ REQUIRES SPECIAL TOOLS -- TO INSTALL. SEE REPAIR 22 220 219 INSTRUCTION MANUAL° 20
