ページ1に含まれる内容の要旨
HSC 585 MULTI
EXTRACTOR
220 - 240V EU
INFORMATION
&
OPERATING
INSTRUCTIONS
CAUTION: DO NOT OPERATE MACHINE
UNTIL YOU HAVE READ ALL SECTIONS
OF THIS INSTRUCTION MANUAL
26022008
11600205211REVA -1-
10.22.2007
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, and offices other than normal residential housekeeping purposes. When using any electrical appliance, basic precautions should always be followed, including the following: NOTE: Read all instructions before using this machine. WARNING! To reduce the risk of fire, electric shock, or injury: • Do not leave the machine unattended when it is plugged-in. Unplug
ページ3に含まれる内容の要旨
INSPECTION: Carefully unpack and inspect your HSC 585-MULTI for shipping damage. Each machine is tested and inspected before shipping. Any shipping damage incurred is the responsibility of the carrier. You should notify the carrier immediately if you notice damage to the box or to the machine or parts. CLEANING SOLUTIONS: Select a proper pre-spray for the surface to be cleaned, and apply the pre-spray. Use a neutral pH rinse or detergent (6 to 9 pH) in the HSC 585 to prevent premature wear of
ページ4に含まれる内容の要旨
Drain Hose KNOW YOUR MACHINE HSC 585 MULTI Drain Hose Cap Wand Holder Vacumm Vacuum Hose Tank Lid Connection Switches Vac Tank 85 Bar Quick Hoses Disconnect Solution Tank Auto Power Dump Garden Hose Wheel Cord Pump Power Connector Prime Pedal Wheel Base Compartment Castor Latch with Brake Pressure Gauge 7 Bar Quick Disconnect HIGH PRESSURE SWITCH PLATE PUMP LIGHT (NO HEAT) DUMP PUMP 5 ON/OFF SWITCH 3 2 4 100 PSI HEAT VACUUM PUMP/HEAT PUMP SELECTED ON/OFF SELECTOR ON/OFF LIGHT SWITCH SWITCH SWI
ページ5に含まれる内容の要旨
REFER TO THE DIAGRAMS ON THE PREVIOUS PAGE OPERATION CAUTION: Never leave the 85 bar pump running if you are not actively using it CAUTION: IF FOAM OR WATER COMES OUT THE VACUUM EXHAUST, TURN THE MACHINE OFF IMMEDIATELY HIGH PRESSURE WASHER 1 Before each use, inspect the machine, hoses, and cleaning tools for cleanliness and completeness. Make sure hoses are in good condition and the spray nozzle(s) is tight. REFER TO THE AUTO-FILL AND AUTO-DUMP INSTRUCTIONS ON THE FOLLOWING PAGES. 2. If you
ページ6に含まれる内容の要旨
HIGH PRESSURE continued water to a clear, solid stream. Priming may take 20 - 60 seconds, or even longer sometimes, and it will require a full solution tank. When the pump is primed, let off the Power Prime Pedal, and turn off the pump and the vacuum. Then press the Power Prime Pedal once again, for a moment, to release the line pressure; you will hear a ‘swoosh’ of air as the back pressure in the lines is released. The pump will need to be primed anytime air gets into it -- try not to let the p
ページ7に含まれる内容の要旨
LOW PRESSURE AND HEAT continued 3. If you choose to use the auto-fill feature, connect the fill-hose to the hose connection over the solution tank fill hole. Turn on the water source, and allow the tank to fill with solution. NOTE: do not turn the water on to full pressure; water flowing into the auto-fill system does not need a lot of pressure behind it. If you choose not to use the auto-fill system, just fill the tank with water and cleaning chemical. Follow chemical directions regarding dilut
ページ8に含まれる内容の要旨
USING THE AUTOMATIC-FILL AND/OR AUTOMATIC-DUMP AUTOMATIC-FILL INSTRUCTIONS Operation: 1. Attach a garden hose to the auto-fill hose connection above the holding tank fill hole, and connect the other end of the hose to your water source. 2. Make sure the float that hangs into the solution tank from the auto-fill valve is free of obstruction and can move freely. 3. Turn on the water supply. Do NOT turn the water on full pressure. This system does not require a high presssure water source. Just tur
ページ9に含まれる内容の要旨
AUTOMATIC-DUMP INSTRUCTIONS Operation: 1. Before each use: if necessary, unscrew the stainless steel filter inside the recovery tank and clean it. Also make sure the float in the recovery tank is clean. 2. Attach a garden hose to the automatic pump-out fitting on the back of the base of the machine (refer to illustration below). 3. Run the other end of the hose into a drain. 4. Turn on the switch for the automatic pump-out (switch is located on the switch panel on the top of the machine). NOTE:
ページ10に含まれる内容の要旨
1 2 5 3 4 6 14 7 23 9 12 8 34 11 10 24 17 21 13 19 25 16 20A 20 15 26 37 30 21A 31 29 27 18 22 28 23 32 HSC 585 Multi REV A 3.8.08
ページ11に含まれる内容の要旨
HSC 585 MULTI PART LIST 220 - 240V ITEM QTY PART No. DESCRIPTION 1 1 600758501 Reel with hoses, complete 2 1 600758502 Lid kit 3 1 600758503 Vacuum air inlet kit 4 1 600758504 Switch plate kit 5 1 600758505 Switch and light kit 6 1 600758506 Auto-fill kit 7 1 600758516 Vacuum tank 8 1 600758508 Heater outlet kit 9 2 600758509 Cord wrap kit 10 1 600758510 Solution tank 11 1 600758511 Fuse kit 12 1 600758512 Water inlet filter kit 13 1 600758513 Power prime kit 14 1 600758514 Drain hose kit 15 1 6
ページ12に含まれる内容の要旨
ACCESSORIES HFT-40 TURBO HARD SURFACE TOOL 600305899 • Use on all types of hard flooring 2 2 • Cleaning capacity is up to 93 m or 1000 ft /Hr • Lightweight, but robust • Brush ring attachment • No wheels to restrict 360° travel • Water temperature up to 110 °C / 230 °F • Patented automatic vacuum compensator leaves the floor dryer • In line filter keeps spray jets clean HFT-45 HFT-43 MINI TURBO HARD HARD SURFACE SURFACE TOOL COMBO TOOL 60070045 60070043 • Great fo getting in those small areas •
ページ13に含まれる内容の要旨
MX 585 MULTI SPECIFICATIONS: Vacuum: 3-stage Rated Power: 2950 W maximum Pump: Positive displacement, 83 bar & Demand,7 bar Suction Power: 372 W Vacuum at Nozzle: 30.4 KPA Heat: to 100 ºC Suction Width: 38 mm Weight: 89.5 KG Dimensions: 39”H x 21”W x 36” L NOTES: 11600205211REVA 11-600205211REVA -13-
