ページ1に含まれる内容の要旨
HR-2410GH
Cold Water
Pressure Washer
Operator's Manual 1
ページ2に含まれる内容の要旨
TABLE OF CONTENTS INTRODUCTION ............................................................................................................................. 3 IMPORTANT SAFETY WARNINGS.............................................................................................4-7 FIRE & VENTILATION PRECAUTIONS ...................................................................................4 SPRAY PRECAUTIONS .....................................................................................
ページ3に含まれる内容の要旨
INTRODUCTION Congratulations on the purchase of your John Deere pressure washer! You can be assured your John Deere pressure washer was constructed with the highest level of precision and accuracy. Each component has been rigorously tested by technicians to ensure the quality, endurance and performance of this unit. This operator's manual was compiled for your benefit. By reading and following the simple safety, installation, operation, maintenance and troubleshooting steps described in
ページ4に含まれる内容の要旨
IMPORTANT SAFETY WARNINGS FIRE & VENTILATION PRECAUTIONS: 1. This unit was designed for outdoor use only. NEVER operate this unit in an enclosed area. ALWAYS make certain there is adequate air (oxygen) for combustion as well as ventilation to prevent the presence of poisonous carbon monoxide gases. Beware of poorly ventilated areas or exhaust fans which can cause inadequate combustion or engine overheating. 2. NEVER operate this unit in the presence of flammable vapors or combustible d
ページ5に含まれる内容の要旨
IMPORTANT SAFETY WARNINGS SPRAY PRECAUTIONS: DANGER RISK OF INJECTION OR SEVERE CUTTING INJURY KEEP CLEAR OF NOZZLE DO NOT DIRECT DISCHARGE STREAM AT PERSONS OR PETS. ONLY TRAINED OPERATORS SHOULD USE THIS PRODUCT. BASIC PRECAUTIONS SHOULD ALWAYS BE OBSERVED, INCLUDING THE FOLLOWING: 1. KEEP AWAY FROM THE SPRAY: a. Because of the high pressure and velocity of the spray, fluids can penetrate the skin, causing serious injury. b. Never point the gun at yourself or anyone else. Never put your ha
ページ6に含まれる内容の要旨
IMPORTANT SAFETY WARNINGS DETERGENT CLEANING PRECAUTIONS: 1. DO NOT use solvents or highly corrosive detergents or acid type cleaners with this pressure washer. Use only mild detergents. 2. KNOW YOUR DETERGENTS! Be prepared to tell a physician exactly what you are using in the event of an emergency. Read the Material Safety Data Sheet (MSDS) provided with your detergent and all detergent labels. Follow all appropriate instructions regarding preparation, use, safety and transportation. K
ページ7に含まれる内容の要旨
IMPORTANT SAFETY WARNINGS ADJUSTMENT PRECAUTIONS: 1. NEVER alter or modify the equipment, be sure any accessory items and system components being used will withstand the pressure developed. Use ONLY genuine manufacturer parts for repair of your pressure washer. Failure to do so can cause hazardous operating conditions and will void warranty. 2. NEVER make adjustments to the machinery while it is connected to the engine without first removing the ignition cable from spark plug. Turning t
ページ8に含まれる内容の要旨
FEATURES FEATURES LISTING 1. Gun Holder 2. Nozzle Holder 3. Quick Connect Assembly 4. Gun Assembly 5. Engine 6. Chemical Hose 7. High Pressure Hose 8. Unloader 9. Chemical Injection Inlet 10. High Pressure Outlet 11. Thermal Relief Valve 12. Pump 13. Water Supply-Inlet 14. Inlet Filter 8 Operator's Manual CV UNITS WITH QC FEATURES 040510
ページ9に含まれる内容の要旨
SAFETY DECALS & PLACEMENT FOR HR-2410GH DO NOT REMOVE SAFETY DECALS FROM UNIT UNLESS REPLACING WITH MOST CURRENT SAFETY DECAL!!! Reference #2 Decal: Caution-Allow to Cool (Part #34-0599) CAUTION/PRECAUCION RISK OF FIRE RIESGO DE FUEGE No ponga combustible cuando Do not add fuel when el producto este en operacion. product is operating. Allow Permita que el motor se enfrie engine to cool for two (2) por 2 minutos antes de minutes before refueling. reablastecer de combustible. 34-059
ページ10に含まれる内容の要旨
INSTALLATION & PREPARATION ATTIRE: Proper attire is essential to your safety. It is advised to utilize whatever means necessary to protect eyes, ears, and skin. Additional safety attire (such as respiratory mask) may be required when using detergent cleaning agents with this washer. SET-UP: DANGER 1. This unit should only be placed on a level surface to ensure proper lubrication RISK OF EXPLOSION OR FIRE! for the engine and water pump while operating. DO NOT PLACE UNIT IN AN 2. DO NOT pl
ページ11に含まれる内容の要旨
INSTALLATION & PREPARATION WARNING NOZZLE REVIEW: RISK OF INJECTION CAUSING Various nozzles may be quick-connected into the end of the wand to change the SEVERE INJURY! spray pattern. When using Quick Connects (Q.C.), be certain the connection -NEVER LOOK DIRECTLY AT THE is securely locked. If not, the high pressure water may shoot the nozzle from NOZZLE ORIFICE UNLESS IT the wand, causing severe injury or serious damage. To determine spray fan, IS DISCONNECTED FROM THE GUN/WAND ASSE
ページ12に含まれる内容の要旨
INSTALLATION & PREPARATION CHECK WATER INLET STRAINER WATER SUPPLY: 1. Select a water supply hose which is a quality grade of garden hose measuring at least 3/4" ID and no longer than 50 feet. 2. Check the water inlet filter to ensure it is clean and free of any obstructions. Periodic cleaning of the water filter will help prevent pump problems. As a filter becomes obstructed, it restricts proper flow of water to the pump. This can result in cavitations which will cause premature failure
ページ13に含まれる内容の要旨
INSTALLATION & PREPARATION PRE-START INSPECTION PROCEDURES: Before starting the unit, perform the following procedures: 1. Check the oil level in the pump and engine. 2. Inspect the water inlet filter. Clean or replace if necessary. See "Water Supply", #2, pg. 12. 3. Check all hose connections to ensure they are securely tightened. See "Water Supply", #3, pg. 12. 4. Inspect for system fuel leaks. If a fuel leak is found, DO NOT START UNIT! See "Fire & Ventilation Precautions", #2 and #4,
ページ14に含まれる内容の要旨
OPERATING INSTRUCTIONS PRIMING THE PUMP: CAUTION 1. It is essential to prime the pump on initial start-up and each time the water supply is disconnected from the unit after initial use. RISK OF UNIT DAMAGE. 2. Lay the high pressure hose out to remove any loops. Water flow will constrict BE CERTAIN THE NOZZLE IS the hose, creating tight loops if the hose is not straight. NOT CONNECTED TO THE UNIT WHILE PRIMING THE PUMP. 3. Securely connect the gun assembly to the high pressure hose.
ページ15に含まれる内容の要旨
OPERATING INSTRUCTIONS CLEANING WITH DETERGENTS: 1. Refer to "Detergent Cleaning Precautions" pg. 6. Be certain to wear protective safety attire as stated on pg. 10. 2. Prepare detergent solution according to label directions. Never pump acids, akalines abrasive fluids or solvents thru the unit. 3. Connect the detergent hose to the unit as shown on page 8. The detergent ratio is preset and cannot be adjusted. 4. Immerse the detergent strainer into the detergent solution to allow detergent
ページ16に含まれる内容の要旨
STORAGE & MAINTENANCE SPECIFIC MAINTENANCE: ENGINE: The engine instructions that accompany your unit detail specific procedures for maintenance of the engine. Following the engine manufacturer’s recommendations will extend engine work life. PUMP: Factory sealed system. Contact customer service with system problems. NOZZLES: Water flow through the spray nozzle will erode the orifice, making it larger, resulting in a pressure loss. Nozzles should be replaced whenever pressure is less th
ページ17に含まれる内容の要旨
WINTERIZING: For storage and transportation purposes in subfreezing ambient temperatures, it will be necessary to winterize this unit. This unit must be protected to the lowest incurred temperature for the following reasons: 1. If any part of the pumping system becomes frozen; excessive pressure may build up in the unit which could cause the unit to burst resulting in possible WARNING serious injury to the operator or bystanders. RISK OF UNIT BURSTING! 2. The pumping system in this unit ma
ページ18に含まれる内容の要旨
TROUBLESHOOTING SYMPTOM PROBABLE CAUSE REMEDY Engine will not start. Various engine problems. Refer to the Engine Manual accompanying your unit. Unit components are frozen. Allow to thaw. If any part of the unit becomes frozen; excessive pressure may build up in the unit which could cause the unit to burst resulting in possible serious injury to the operator or bystanders. No discharge at nozzle when Inadequate water supply. Ensure hose is 3/4"
ページ19に含まれる内容の要旨
STATEMENT OF WARRANTY John Deere warrants all parts, (except those referred to below), of your new pressure washer to be free from defects in materials and workmanship during the following periods: For One (1) Year from the date of original purchase: Cart Assembly Plumbing High Pressure Pump GFCI For Ninety (90) days from the date of original purchase: Trigger Gun High Pressure Hose Strainer/Filters On/Off Switch Unloader Valve Defective parts not subject to normal wear and
ページ20に含まれる内容の要旨
NOTES 20 Operator's Manual
