ページ1に含まれる内容の要旨
WHEEL KIT FOR 13 HP
GENERATOR
94192
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may
differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2006 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For t
ページ2に含まれる内容の要旨
Specifications Item Description Tires 2 – 8 inch pneumatic tires; Inflation: 30 PSI Axle Steel, 0.6 inch diameter Handle Steel, 0.86 inch diameter, 18 inches long Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future referenc
ページ3に含まれる内容の要旨
10. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 11. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired. 12. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine th
ページ4に含まれる内容の要旨
Optionally, if the Generator gas tank is empty, the Generator can be tipped on its back frame for ease of mounting the Axle (49), Wheels (50), and Shock Absorbing Feet (54). This should only be done on flat, cement surface. 2. Open the bag of hardware and remove four Bolts (52), Nuts (57), Lock Washers (64), Pins (51), Washers (63), and two Axle Brackets (53). 3. Place Bolt (52) and Washer (63) up through Axle Bracket (53), then up and into the Frame Cross Bracket. Secure from above with Nut (57
ページ5に含まれる内容の要旨
8. Inflate each Wheel (50) tire to 30 PSI. Replace valve cap. 9. Find two Brackets (56) and Foot (54), and two Bolts (55), four Bolts (52), six Nuts (57), six Washers (63), and six Lock Washers (64). 10. Mount each Foot (54) to the Bracket (56) using Bolt (55), Lock Washer (64), and Nut (57). Securely tighten. (See photo below.) 11. Mount each Bracket to the Frame Cross Bracket using two Bolts (52), Nuts (57), Washers (63), and Lock Washers (64). Securely tighten. Nut (57) not shown Lock Washer
ページ6に含まれる内容の要旨
Maintenance 1. Periodically check the tire pressure. It should be 30 PSI. 2. Periodically tighten all Generator frame nuts and bolts. Parts List Item Description Qty 49 Axle 1 50 Wheels 2 51 Pin 4 52 Bolt, M8x25 8 53 Axle Bracket 2 54 Shock Absorbing Foot 2 55 Bolt, M8x25 2 56 Foot Bracket 2 57 Nut, M8 12 61 Handle 1 62 Bolt, M8x45 2 63 Washer, M8 24 64 Lock Washer, M8 12 66 Washer, M16 4 NOTE: Some parts are listed and shown for illustration purposes only and are not available
ページ7に含まれる内容の要旨
Assembly Drawing Page 7 SKU 94192 For technical questions, please call 1-800-444-3353
