ページ1に含まれる内容の要旨
6’ x 6’ Greenhouse
97439
set up and Maintenance instructions
®
distributed exclusively by harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve this Manual.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without t
ページ2に含まれる内容の要旨
notice is used to sa Ve this Manual address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- caution, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
ページ3に含まれる内容の要旨
snow or other debris can cause parts unpackinG of this greenhouse to buckle sud- denly. Do not allow snow or debris When unpacking, check to make sure to accumulate on top of the green- that the item is intact and undamaged. If house. NEVER enter a greenhouse any parts are missing or broken, please with accumulated debris on top. call Harbor Freight Tools at the number shown on the cover of this manual as soon 4. Assemble the Greenhouse in a as possible. smooth, level area that is shel
ページ4に含まれる内容の要旨
Figure for pole assembly (steps 4-6) asseMbl Y instructions read the entire iMportant saFetY inForMation section at the beginning of this manual including all text under subheadings therein before set up or use of this product. note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 4. Fit the covered Rafter Slats into the grooves in the Rafter Poles (G) and note: The Greenhouse is heavy and slide i
ページ5に含まれる内容の要旨
8. Secure both top corners using a Figure for bar installation (steps 13-14) Connector B on the left side and a Connector C on the right side, again make sure the unconnected point on the Connectors face towards you. 9. Secure the bottom left-hand corner of the Panel with Connector D. Use the Hex Wrench (T) to fasten a Hex Screw (S) into the hole on the bottom of the Bottom Pole. 10. Secure the bottom right-hand corner of the Panel with Connector E. Use the Hex Wrench (T) to fasten a
ページ6に含まれる内容の要旨
to the ground. Use the two remaining Figure for bar connection (steps 15-19) Stakes to secure the door flap. Maintenance and ser VicinG 1. Periodically, inspect the general con- dition of the product. Check for loose screws cracked or broken parts, and any other condition that may affect its safe operation. If any defects are found have them repaired or the parts replaced immediately. 2. Clean external surfaces of the prod- uct with clean, moist cloth. 15. Find the holes in the Bars (I
ページ7に含まれる内容の要旨
please read the FolloWinG careFull Y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS QUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACE
ページ8に含まれる内容の要旨
asseMbl Y diaGraM M l record product’s serial number here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 97439 For technical questions, please call 1-800-444-3353. Page 8
