ページ1に含まれる内容の要旨
Nautilus® Nautilus® Nautilus® U514 U514 U514 Upright Upright Upright Exercise Exercise Exercise Bike Bike Bike
003–3242–110609C
ページ2に含まれる内容の要旨
Para obtener este manual en Español Latino Americano vaya a: http://support.nautilus.com. Table of Contents 3 Parts 6 Important Safety Instructions 4 7 Specifications Assembly Before Assembly 4 Level Y our Bike 20 T ools Required 5 21 Contacts 5 Hardware Instructions de montage 23 © 2009 Nautilus, Inc., All rights reserved ™ and ® indicate a trademark or registered trademark. Nautilus, Inc. (www .nautilus.com) trademarks include NAUTILUS®, BOWFLEX®, ST AIRMASTER®, SCHWINN® and UNIVERSAL® and res
ページ3に含まれる内容の要旨
Important Safety Instructions This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury . Obey the following warnings: Read and understand all warnings on this machine. Carefully read and understand the Assembly Manual. • • • Keep bystanders and children away from the product you are assembling at all times. • • • Do not connect power supply to the machine until instructed to do so. • • • Do not assemble equipment in a wet or damp location.
ページ4に含まれる内容の要旨
Specifications Before Assembly Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a hard, level surface. Allow a workout area of minimum 82” x 61” (2.1m x 1.5m). Follow these basic points when you assemble your machine: 1. Read and understand the “Important Safety Instructions” before assembly. 2. Collect all the pieces necessary for each assembly step. 3. Using the recommended wrenches, turn the bolts and nuts to the right (clockw
ページ5に含まれる内容の要旨
Tools Included Not Included 6mm Hardware Item Qty Description Item Qty Description 1 2 A M8 x 85 Hex Bolt G Flat W asher B 1 M8 x 85 Carriage Bolt H 1 M8 Lock Nut C 4 M8 x 16 Hex Screw I 1 T -Nut 4 1 D M8 x 16 Button Head Hex Screw J Narrow W asher E 4 Arc W asher K 1 Console slider adjustment knob F 4 Cover L 1 Console tilt adjustment knob 5 5 5
ページ6に含まれる内容の要旨
Parts Item Qty Description Item Qty Description 1 1 8 1 Rear Stabilizer Console 2 1 Front stabilizer 9 1 Console Bracket 3 1 Main Frame 10 1 W ater Bottle Holder 4 1 11 1 Seat Power Cord 5 1 1 Seat Post 12 Right Pedal 6 1 Console Mast 13 1 Left Pedal 7 1 Handlebar 6 6 6
ページ7に含まれる内容の要旨
Assembly 1. Install Front and Rear Stabilizers 7 7 7
ページ8に含まれる内容の要旨
2. Install Pedals 8 8 8
ページ9に含まれる内容の要旨
3. Install Seat Post 9 9 9
ページ10に含まれる内容の要旨
4. Install Seat 10 10 10
ページ11に含まれる内容の要旨
5. Connect Console Mast Cable to Frame Assembly Cable 11 11 11
ページ12に含まれる内容の要旨
6. Attach Console Mast NOTICE: Do not crimp Console Cable. 12 12 12
ページ13に含まれる内容の要旨
7. Install Handlebar Note: Put the T -nut (I) into the Handlebar slider and align it with the second hole (7a) to install the Console Slider Adjustment Knob (K) and washer (J). Make sure that the lower Heart Rate cable (7b) is connected. NOTICE: Do not crimp the cables. 13 13 13
ページ14に含まれる内容の要旨
8. Install Console Bracket NOTICE: Do not crimp the cables. 14 14 14
ページ15に含まれる内容の要旨
9. Connect Console Mast Cable and Heart Rate Cable to Console 15 15 15
ページ16に含まれる内容の要旨
10. Attach Console to Console Bracket Note: Hardware is pre-installed on Console and not on Hardware Card. NOTICE: Do not crimp the cables. 16 16 16
ページ17に含まれる内容の要旨
11. Adjust and Tighten the Console Mast 17 17 17
ページ18に含まれる内容の要旨
12. Install Water Bottle Holder Note: Hardware is pre-installed on Mast and not on Hardware Card. 18 18 18
ページ19に含まれる内容の要旨
13. Connect Power Cord to Frame Assembly Final Inspection Inspect your machine to ensure that all fasteners are tight and components are properly assembled. Do not use or put the machine into service until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’ s Manual. 19 19 19
ページ20に含まれる内容の要旨
Level Your Bike Levelers are found on each side of the Rear Stabilizer . T urn the knob to adjust the stabilizer foot. Make sure the bike is level and stable before you exercise. 20 20 20
