ページ11に含まれる内容の要旨
Pro Rack Type Modelers or Preamps EFFECTS EFFECTS LOOP LOOP RETURN RETURN MODEL REACTOR 112 MODEL REACTOR 112 Atomic Amplifiers LLC. Atomic Amplifiers LLC. Orange CT. Orange CT. SEND - L SEND - L !CAUTION! !CAUTION! 0101010101 FUSE 0101010101 FUSE SEND - R SEND - R Using two Reactor Replace the DS-1’s back Plug the Left and Right 50 112/212s into the docking bays outputs of your Pro- Install blank located in the top o
ページ12に含まれる内容の要旨
Connecting an external Loudspeaker Box On the rear side of the Atomic Reactors 50 112/212/50 and the 212/50 is a Output Jack for an external Loudspeaker Box. The impedance should not exceed 8 Ohms, use a professional loudspeaker cable not a guitar cable which can melt and burn. The red push-button “Internal O N/O FF” is there to turn the internal loudspeaker on or off, when an external box is connected. This button must be turned on when no loudspeaker box is attached. Adjusting and r
ページ1に含まれる内容の要旨
Reactor 50-112 / 50-212
Owners Manual
Copyright 2006 by G66 GmbH
ページ2に含まれる内容の要旨
Introduction Congratulations on your purchase of an Atomic Reactor 50 112/212, a major step in bringing vacuum tube analogue musicality to the digital world. The Reactor 50 112/212 is an extremely versatile musical instrument that provides a live performance platform for your modeling tools and instrument processors. The Reactor 50 112/212 is clearly different from other guitar amplifiers. What we would like to accomplish in the following pages is to bring you up to speed on exactly how
ページ3に含まれる内容の要旨
Once a modeler is installed in the DS-1, all of the signal input and output as well as the power supply connections are made. No wall wart or external power is required, the Reactor automatically selects and sends the correct power / voltage to the modeler loaded DS-1. Installation and de-installation is quick and requires no tools. The DS-1 is then easily loaded into the Reactor 50 112/212. A blank template is also available for people who wish to use rack mount modelers and other choices
ページ4に含まれる内容の要旨
The Atomic Reactor is a full range system, its special loudspeakers can handle frequencies up to 18 KHz, which is the same as a normal PA system. You can switch the output m ode from „Studio/D irect“, „D irect M ode“, „Recording O ut“ or „D irect O ut“, so that the right speaker, box and m icrophone m odels are activated. The output signal of the Modelers can be sent direct to a Mixer via the Send Jacks (left/right) on the rear side of the Atomic Amps, for an absolute professional PA
ページ5に含まれる内容の要旨
Template Kits The installation of your modeler into a Dock requires the proper matching template kit. Currently, the following kits are available. MODELER PART # ATP2 LINE 6 POD LINE 6 POD XT ATPXT BEHRINGER V-AMP ATVAMP ATVAMP BEHRINGER V-AMP 2 Template Kits are designed to adapt VOX TONELAB ATTLAB most popular desktop modelers into the Atomic DS-1 Docking Unit. A template kit consist of a pre-fitted, injection molded frame and the appropriate mounting hardware to hol
ページ6に含まれる内容の要旨
Screw the 3 thumbscrews labeled “A”, "B” &”C”, into the corresponding holes located on the bottom of the DS-1. Attach the 3 rounded mushroom heads caps to the ends of the locking screws. * *A set of mushroom heads come shipped with each Reactor 50 112/212. Position the proper docking template on the top of your modeler. Insert the docking template along with the modeler into the rear of the DS-1, locating and positioning it in the notc
ページ7に含まれる内容の要旨
Check if everything is connected correctly and then let the „D ocking Station“ click into place. If this sounds com plicated, don’t w orry, it isn’t. Just try it, it’s easier than you think. Now turn the Master-Volume-Control on the rear side of the Atomic to the left (Volume off) and switch the red Power Switch on, after of course connecting the amplifier to the mains. Your Modeler will also switch on and the red power switch will light up, err red? Yeah you guessed it. Even the tubes w
ページ8に含まれる内容の要旨
Remove the template frame of the DS- 1 Still got the screws? Replace the template frame with a blank template (Atomic Part # ATBLANK – purchased separately). Still got the screws? Replace the 8 screws. (Whew!) You can now load the DS-1 into the Reactor as usual *. The Reactor is now ready to be used with a Pro-rack or foot controller style modeler NOTE! When bypassing the DS-1, the “RETURN” input on the rear *
ページ9に含まれる内容の要旨
Desktop Modeler in Stereo EFFECTS EFFECTS LOOP LOOP RETURN RETURN MODEL REACTOR 112 MODEL REACTOR 112 Atomic Amplifiers LLC. Atomic Amplifiers LLC. Orange CT. Orange CT. SEND - L SEND - L !CAUTION! FUSE 0101010101 SEND - R !CAUTION! 0101010101 FUSE SEND - R PLEASE NOTE! * If you wish to use a pair of Reactors in MONO, simply use the SEND – L output instead of SEND – R.
ページ10に含まれる内容の要旨
Floorboard Style Modelers EFFECTS EFFECTS LOOP LOOP RETURN RETURN MODEL REACTOR 112 MODEL REACTOR 112 Atomic Amplifiers LLC. Atomic Amplifiers LLC. Orange CT. Orange CT. SEND - L SEND - L !CAUTION! !CAUTION! 0101010101 FUSE 0101010101 FUSE SEND - R SEND - R Using two Replace the DS-1’s back Plug the Left and Right Reactor 50 into the docking bays outputs of your Foot 112/212s Install located in the t
