ページ1に含まれる内容の要旨
PILEJOGGER II
Operating Instructions (ENG)
MODELS: PJ2A 8.604-176.0
PJ2AIE 8.604-177.0
Read instructions before operating the machine.
8603750 - G 03/04/08
PRV NO. 98018
ページ2に含まれる内容の要旨
MACHINE DATA LOG/OVERVIEW MODEL _______________________________________ DATE OF PURCHASE __________________________ SERIAL NUMBER ______________________________ SALES REPRESENTATIVE # _____________________ DEALER NAME ________________________________ OPERATIONS GUIDE NUMBER ___________________ PUBLISHED __________________________________________
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Machine Data Log/Overview.........................2 Table of Contents..........................................3 HOW TO USE THIS MANUAL How to use this Manual.................................1-1 SAFETY Important Safety Instructions ........................2-1 Hazard Intensity Level. .................................2-2 Grounding Instructions..................................2-3 OPERATIONS How the Machine Works. ....................
ページ4に含まれる内容の要旨
HOW TO USE THIS MANUAL The SAFETY section contains important information This manual contains the following sections: regarding hazard or unsafe practices of the machine. Levels of hazards is identified that could - HOW TO USE THIS MANUAL result in product or personal injury, or severe injury - SAFETY resulting in death. - OPERATIONS - MAINTENANCE The OPERATIONS section is to familiarize the - PARTS LIST operator with the operation and function of the machine. The HOW TO
ページ5に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. ! WARNING: To reduce the risk of fire, electric shock, or injury: Do not operate without filters (dry or wet) in place. Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments. If the machine i
ページ6に含まれる内容の要旨
HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: ! WARNING WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. ! CAUTION CAUTION - Hazards or unsafe practices which could res
ページ7に含まれる内容の要旨
GROUNDING INSTRUCTIONS THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit . The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. Improper connection of the equipment- EXTENSION CORDS: grounding conductor can result in a risk of If an e
ページ8に含まれる内容の要旨
OPERATIONS USING PILEJOGGER II WITH EXTRACTOR 1. Connect vacuum and solution hoses to PILEJOGGER. 2. Plug power cord into properly grounded outlet. 3. Move PILEJOGGER to starting place. Turn on brush drive motor by depressing foot switch located on top of cleaning head. Depress solution valve lever fully and move backward at a steady pace (25 to 30 feet per minute). NOTE: Lift the handle slightly as you move backward so the weight is almost off the rear roller. This will b
ページ9に含まれる内容の要旨
MAINTENANCE DAILY MAINTENANCE 1. Vacuum unused cleaning solution from solution tank into recovery bucket. 2. Flush two gallons of clean water through pumping system of extractor, PILEJOGGER and hand tools. Twice a month, flush a vinegar solution (one quart white vinegar to two gallons water) or browning prevent solution (mixed as directed) through extractor and PILEJOGGER. This will minimize buildup of alkaline residue in the system. 3. Remove carpet lint from brush fibers and underside
ページ10に含まれる内容の要旨
PILEJOGGER ASSEMBLY 86037500 PJ2A 03/04/08 5-1
ページ11に含まれる内容の要旨
PILEJOGGER ASSEMBLY SERIAL NO. REF PART NO. PRV NO. QTY DESCRIPTION NOTES: FROM 1 86000890 09013 2 BEARING, PJ2A SHAMBAN 2 86229780 14130 2 BLOCK, PJ BEARING MTG 3 86263880 03018 1 AXLE, PJ BRUSH 4 86273930 70051 2 SCR, 8-32 X 1/2 PPHMS NP 5 86230780 14048 1 BRUSH, PJ 6 86250410 64001 1 PULLEY, PJ2 W/ .314 BORE 7 86006570 70084 3 SET SCR, 8-32 X 3/16 KCP DL 8 86001050 11005 1 BELT, BRUSH DRIVE 9 86252350 67034 1 ROLLER, PJ2A 10 86263870 03014 1 AXLE, .375 X 13.31
ページ12に含まれる内容の要旨
230V SERVICE PARTS PART NO. PRV NO. DESCRIPTION NOTES: 86247120 53147 MOTOR ASM, 230V DC PM SERVICE ONLY 86261060 23718 CORD ASM, 1.0MM 3 X 40 HODVVF SERVICE ONLY 86001780 14308 CIRCUIT BREAKER, .8A (230V) SERVICE ONLY 86037500 PJ2A 03/04/08 5-3
