ページ1に含まれる内容の要旨
PROFESSIONAL PHOTO LAMINATOR
OWNER'S MANUAL
NPH-1200N/900N
NPH-1200 / 900
PLEASE READ AND SAVE INSTRUCTIONS
ROYAL SOVEREIGN INTL.INC.
1
ページ2に含まれる内容の要旨
TABLE OF CONTENTS TOPICS PAGE 3 INTRODUCTION ------------------------------------------ SAFETY PRECAUTIONS ------------------------------------ 3 CHARACTERISTICS OF NPH-1200N/900N ---------------------- 4 5 SPECIFICATIONS ----------------------------------------- 5 SETUP ------------------------------------------------ MAJOR PARTS IDENTIFICATION ------------------------------ 6 CONTROL PANEL INSTRUCTIONS ---------------------------- 7 7 1.CONTROL PANEL SETTINGS ---------------------------
ページ3に含まれる内容の要旨
INTRODUCTION Thank you for purchasing a Royal Sovereign Laminating Machine. To insure high quality lamination, please read this instruction manual thoroughly. For additional product support or factory-direct ordering information, call Royal Sovereign Customer Service at (201)568-0830 or toll free call, (800)397-1025. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating the machine. Keep this information for future ref
ページ4に含まれる内容の要旨
CHARACTERISTICS OF LAMINATOR NPH-1200N/900N This machine has been designed using the latest laminating technology. 1. This machine is controlled by a state-of-the-art Microprocessor. a) Protect the rollers--When the power is off or a power failure occurs, rollers continue to turn until the unit properly cools down. b) Automatic overheating protection--If a temperature sensor should fail, the heating elements will not heat up. c) You can set your own operating conditions into "Memory". 2. T
ページ5に含まれる内容の要旨
SPECIFICATIONS Description NPH - 1200N NPH - 900N 580x290x135mm 505x290x135mm Dimensions(w x d x h) (22.8"x11.4"x5.3") (19.9"x11.4"x5.3") 330mm 240mm Max.Laminating Width (13") (9.4") 2mm Max.Lam. Thickness (1/12") 75 ~ 250mic Film Thickness (3 ~ 10 mil) Transport Type Four Roller (no carrier) Heat Source Hot Roller Type Pre-Heating Time 4 ~ 5 min Temp. Operating Range 20 ~ 160℃ Cooling Fan Type DC FAN Motor Type DC GEARED MOTOR 750mm/min Max. Laminating Speed (29.5" per min) 11Kg 9Kg Weight (24
ページ6に含まれる内容の要旨
MAJOR PARTS IDENTIFICATION 1. Top Cabinet 2. Roller Cover 3. Roller Cover Screws 4. Control Panel 5. LCD Window 6. Input 7. Output 8. Power Cord 6
ページ7に含まれる内容の要旨
CONTROL PANEL INSTRUCTIONS Appropriate speed and temperature may be set, using the LCD controller. The LCD panel was designed for convenience, by incorporating the ability to program your settings into "Memory". 1. CONTROL PANEL SETTINGS LCD DISPLAY T-Check HOT/COLD COLD BUTTONS MEMORY 7
ページ8に含まれる内容の要旨
2. LCD WINDOW 1. * 6 film thickness options 75 Mic=3 mil, 100 Mic=4 mil, 125 Mic=5 mil 175 Mic=7 mil, 250 Mic=10 mil 2. SPEED * 7 speed options Setting 1 is slowest / Setting 7 is fastest 3. TEMPERATURE Display the present temperature. 4. Is displayed when the present temperature is reached. 5. Indicates to wait till blinking stops. Current temperature is higher or lower than the preset temperature. 6. Displayes the direction of the rollers. 7. Shows cold function. 8
ページ9に含まれる内容の要旨
3. BUTTON FUNCTIONS T-Check : Check current temperature T-Check HOT/COLD : Hot/Cold function : Working condition and HOT/COLD COLD MEMORY Cold function cancel MEMORY : Increase temperature : Decrease temperature : Increase speed : Decrease speed : Restore the memorized working setting : Restore the memorized working setting : Reverse function : Power On/Off 9
ページ10に含まれる内容の要旨
4. HOW TO SET THE BUTTONS (Buzzer rings each time you press the button.) ***SET TEMPERATURE*** 1.Temperature available range from 20℃ to 160℃. 2.Each time you press or to set temperature, it will change 1℃(1℉) at a time. If you press the button for more than 2 seconds, temperature will change automatically. ***SPEED CONTROLS*** 1.You can use 7 different lamination speed. 2.You can change speed with or ***CHECK T
ページ11に含まれる内容の要旨
***MEMORIZING WORKING CONDITION AND USING THE MEMORIZED WORKING CONDITION*** 1) Memorizing working condition 1. The laminator can memorize up to 6 settings. 2. Use up and down arrows to set or 3. When you complete the optimum laminating conditions (Speed & Temperature), MEMORY button. This setting is memorized and confirmed when the light blinks. MEMORY 4. To enter other settings into memory, repeat steps 2 and 3. 2) Using the memorized settings 1. You can choose any
ページ12に含まれる内容の要旨
LAMINATING STEPS 1. HOT LAMINATING 1. Press the power button. 2. Please refer Information Panel on the front of product. 3. Select a memory setting by pressing the and button. 4. It is ready when the LCD window shows and the buzzer rings three times. 5. After Insert document or photograph to be laminated into a laminating pouch, insert pouch squarely into opening slot. 6. Finished laminated pouch will exit through rear of machi
ページ13に含まれる内容の要旨
2. COLD LAMINATING 1. Press the power button to turn on. HOT/COLD 2. Press 3. It is ready when LCD window shows and the buzzor rings three times. 4. Insert document into a Royal Sovereign cold laminating pouch as follows. **HOW TO ATTACH DOCUMENT ON COLD POUCH FILM** 1) Prepare cold pouch film. 2) Remove protective paper inside cold pouch. Back (Be careful not to allow the pouch to close and seal itself closed. If the pouch closes on itself and seals,you will not be abl
ページ14に含まれる内容の要旨
3. COLOR FOIL LAMINATING **Your laminator has ability to add color by applying color foil to documents copied or printed by lasor printer or toner copier.** **PAPER CARRIER is required** 1. Press the power button to turn the laminator on. 2. Find FOIL FUNCTION using the up arrow. 3. It is ready when LCD window shows and the buzzer rings 3 times. 4. Position the color foil on document and put it in paper carrier. 5. Feed paper carrier squarely into opening slot. 6. Fin
ページ15に含まれる内容の要旨
4. MOUNT BOARD LAMINATING **You can laminate photographs or pictures on a hard mounting board up to 2mm thickness** 1. Press the power button to turn on. 2. Temperature 130 and speed 1 is set for Foil function. 3. It is ready when LCD window shows and the buzzor rings 3 times. 4. Set material on Mount board then slide them into the opening slot 5. Finished board will exit through the rear slot of machine. 6. When finish, press the power button and turn off. ***USEFUL INFORMATION**
ページ16に含まれる内容の要旨
HOW TO CLEAN ROLLERS AND REMOVE STUCK OR JAMMED TO FILMS 1. Cleaning rollers with a clean and thick paper 1) If film adhesive apears on the laminated pouch surface, Insert a sheet of clean, thick paper (about 0.5mm(1/50") thickness) into the machine 2~3 times on 100℃(212℉) setting. The paper will attract the excess adhesive from the roller. 2. Cleaning rollers with cleaning solvent. 1) When rollers are hot, turn on and set "COLD" mode to cool them down. 2) After cooling, the
ページ17に含まれる内容の要旨
IMPORTANT SAFETY CONCERNS 1. Please be cautious that neckties, necklaces, long hair and clothing are kept well away while operating the laminator. 2. Prevent children from accessing the machine. 3. Make certain that the machine is connected to an adequate power source. 4. Do not use for any purpose other than lamination. MAINTENANCE 1. Width of upper and lower side of film should be same in order not to allow melted adhesive resin to stick to the rollers. 2. Routine cleaning of rollers
ページ18に含まれる内容の要旨
ONE YEAR LIMITED COMMERCIAL/PROFESSIONAL WARRANTY This product is warranted for 1 year from date of purchase to be free from electrical or mechanical defects in material and workmanship. Should product fail to operate during warranty period, return it, freight prepaid, to Royal Sovereign Corporation, 100 West Sheffield Avenue, Englewood, NJ 07631, for service. There will be no charge for parts and labor to repair or replace this product whthin warranty period. When returning machine, purchaser m
