ページ1に含まれる内容の要旨
2.5 liter, non-medical
ultrasonic cleaner
model 95563
assembly and operation instructions
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
t o preVent serious injury, read and understand
all warnings and instructions before use.
© ®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork containe
ページ2に含まれる内容の要旨
specifications Electrical Requirements 120 Volts AC/60 Hz 4’8”; 18 AWG X3C SVT, 3 Power Cord prong, 160 W Dimensions 7-1/4” H X 11-3/8” L X 9” W Tank Dimensions 3” D X 9-3/4” L X 5-1/2” W Tank Capacity 2.5 L Heated Water Temperature 149° F save this manual You will need this manual for the safety warnings and precautions, assembly, oper- ating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the
ページ3に含まれる内容の要旨
check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 2. double insulated products are equipped with a polarized plug (one blade is wider than the other). this plug will fit in a polarized outlet only one way. if the plug does not fit fully in the outlet, reverse the plug. if it still does not fit, c
ページ4に含まれる内容の要旨
t ool use and care 1. do not force the product. use the correct product for your application. The correct product will do the job better and safer at the rate for which it is designed. Do not force the product and do not use the product for a purpose for which it is not intended. 2. do not use the product if the power switch does not turn it on or off. Any product that cannot be controlled with the Power Switch is dangerous and must be replaced. 3. disconnect the power cord plug from th
ページ5に含まれる内容の要旨
2. maintain a safe working environment. Make sure there is adequate surrounding workspace. Do not use this product in a damp or wet location. 3. people with pacemakers should consult their physician(s) before using this product. electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker. 4. never leave this product unattended when it is plugged into an electrical outlet. Turn off the product, and unplug it from its electrical
ページ6に含まれる内容の要旨
grounded t ools: t ools witH tHree prong plugs The Ultrasonic Cleaner has a 3-prong plug. 1. Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resis- tance path to carry electricity away from the user, reducing the risk of electric shock. (see 3-prong plug and outlet.) 2. The grounding prong in the plug is
ページ7に含まれる内容の要旨
5. If you are using one extension cord for more than one tool, add the nameplate am- peres and use the sum to determine the required minimum cord size. (see t able a.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electri- cian
ページ8に含まれる内容の要旨
unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. operation note: FAILURE TO FILL THE ULTRASONIC CLEANER WITH WATER OR A NON-COR- ROSIVE CLEANING MATERIAL BEFORE USING WILL SEVERELY DAMAGE IT AND VOID THE WARRANTY. 1. Make certain that the Cleaner ON/OFF Switch is in the “OFF” position. Make cer- tain that the Ultrasonic
ページ9に含まれる内容の要旨
4. Unplug the Cleaner. Open the lid and remove the item using tongs. cleaning witH Heat 1. Press the “TC” Button to use the heat function during a cycle of the Ultrasonic Clean- er. A red light on the readout will light up, indicating that the Heat cycle is on. 2. On some occasions, the initial cleaning may not adequately clean the article. A second period of cleaning usually finishes the cleaning process. Pressing the “ON” Button will restart the cycle. 3. To pause or stop the cycle, press
ページ10に含まれる内容の要旨
troublesHooting problem possible causes probable solutions Cleaner will not start 1. No power at outlet. 1. Check power at outlet. 2. Cord not connected. 2. Check that cord is plugged in. 3. Overheating Safety Off feature 3. Allow fifteen minutes before kicked in attempting to use the Ultrasonic Cleaner parts list part description Q’ty part description Q’ty 1 Lid 1 15 Fan Cover 1 2 Left Transparent Lid 1 16 Fan 1 3 Panel Cover 1 17 Bottom Housing 1 4 Decorated Cover 1 18 Circuit Board 1 5 Pres
ページ11に含まれる内容の要旨
assembly diagram Parts #27 Transducer and #28 Cord/Plug not shown SKU 95563 for technical questions, please call 1-800-444-3353. Page 11
ページ12に含まれる内容の要旨
warranty LIMIteD 90 DAy/1 yeAr w ArrAnty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser for a period of ninety days from date of purchase that the motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Harbor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all other
