ページ1に含まれる内容の要旨
• • P Please r lease read this man ead this manual and ual and
s sa av ve e it with y it with your or our original iginal
sales r sales receipt. eceipt.
• • T To ools needed f ols needed for assemb or assemblly y: :
t tw wo o assemb assemblly y wr wrenc enches hes
(inc (included) and a Phillips luded) and a Phillips
S Scr cre ew wdr driv iver (not inc er (not included). luded).
® ®
• • U Use onl se only with a P y with a Po ow wer er Wheels Wheels
1 12 2 V Vo olt Lead-A lt Lead-Ac
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Warnings and Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
ELECTRICAL HAZARD DANGER • To prevent electric shock, do not immerse in water; wipe clean with a damp cloth. WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery retainer. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fi re resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fi re or explosion resulting in serious injury. ® ® - Use of P ower W
ページ4に含まれる内容の要旨
PARTS • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Some parts were placed under the seat for shipment. Press the tab under the back of the seat and lift to access the battery compartment. • Metal parts have been coated with a lubricant to protect
ページ5に含まれる内容の要旨
12 Volt Charger Rear Axle 12 Volt Battery 2 Bushings 2 Hand Grips 2 Wrenches 4 Hubcaps 4 Wheel Covers Part Not Shown: Label Sheet 7 3 3 #8 x /4" Screw - 4 #8 x 2" Screw - 2 /16" Washer - 2 /8" -16 Hex Nut - 3 Fasteners Shown Actual Size For your convenience, we included extra fasteners! Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. P9723b-0920 5
ページ6に含まれる内容の要旨
PARTS PICTURE Note: Some parts shown are assembled on both sides of the vehicle. 2 3 14 4 12 1 7 5 6 8 10 11 17 20 9 8 10 11 13 15 16 18 19 1 Vehicle 7 Rear Wheel - 2 13 Bushing - 2 19 Wrench - 2 2 Handlebar 8 Wheel Cover - 4 14 Hand Grip - 2 20 Front Wheel - 2 7 3 Seat 9 /16" Washer - 2 15 Plate Parts Not Shown 3 4 12 Volt Battery 10 /8" -16 Hex Nut - 3 16 Steering Column Cap Label Sheet 5 Rear Axle 11 Hubcap - 4 17 Front Clip #8 x 2" Screw - 2 6 Rear Wheel Driver - 2 12 12 Volt Batte
ページ7に含まれる内容の要旨
BATTERY CHARGING ELECTRICAL HAZARD WARNING CAUTION • Battery can fall out and injure a child if Use the charger in dry locations only. vehicle tips over. Always use battery retainer. • PREVENT FIRE About Thermal Fuses - Never modify the electrical system. ® Your Power Wheels 12 volt battery is equipped with a built-in Alterations could cause a fi re resulting thermal fuse. The thermal fuse is a self-resetting safety device in serious injury and could also ruin the which automatically “tr
ページ8に含まれる内容の要旨
ASSEMBLY WARNING Children can be harmed by small parts, sharp edges and sharp points in the vehicle's unassembled state, or by electrical items. B Care should be taken in unpacking and Battery assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. A Rear Wheel Driver (Slotted Side Down) Charger Connector Rear Wheel (Indented Side Down) A • Plug the charger connector into the battery . B • Plug the charger into a stand
ページ9に含まれる内容の要旨
Motor Assembly Rear Axle Assembly Wrench BOTTOM VIEW 2 • Position the vehicle upside down. 3 /8" -16 Hex Nut 4 • Slide the rear axle assembly through the hole in the back end of the vehicle, as shown. Make sure the rear wheel driver fits 3 • Fit a /8" -16 hex nut onto the end of the rear wheel assembly. into the pins in the motor assembly inside the vehicle. • Completely tighten the hex nut on the rear wheel assembly with the wrench. Hint: An extra wrench has been provided to hold the hex n
ページ10に含まれる内容の要旨
Steering Column Plate BOTTOM VIEW 6 8 • Lift the front end of the vehicle up slightly. Check to be sure • Slide the plate under the steering column, as shown. the steering column fits through the hole in the steering 3 • Insert a #8 x /4" screw into the plate and tighten. linkage. Lower the front end of the vehicle. Front Wheel (Flat Side First) Washer Front Axle Steering Column Cap Bushing Wheel Cover (Ring End First) (Indented Side Out) 9 7 • Slide a /16" washer onto the front axle. • Slid
ページ11に含まれる内容の要旨
Wrench 3 /8" -16 Hex Nut SIDE VIEW 10 3 • Fit a /8" -16 hex nut onto each end of the front axle. Tighten Front Clip both hex nuts with the wrench. FRONT VIEW 12 • Fit the front clip onto the front of the vehicle, as shown. Hubcaps Hint: The front clip may be factory assembled. Hubcaps BOTTOM VIEW 11 • “Snap” a hubcap onto the center of each wheel cover. • Turn the vehicle upright. Brush Guard 13 • Fit the brush guard onto the front clip. 3 • Insert two #8 x /4" screws into the lower holes in th
ページ12に含まれる内容の要旨
Drive Buttons Connector 16 • Locate the opening under the drive buttons. 14 • Reach into the opening and pull the high speed connector out through the opening. • Insert two #8 x 2" screws into the upper holes in the brush • See page 18 for information on high speed operation. guard and tighten. Drive Buttons A Hand Grip Hand Grip Seat B BACK VIEW 15 17 • Fit both hand grips on the ends of the handlebar. Hint: If it is difficult to slide a hand grip onto the handlebar, • Fit the tab at the fro
ページ13に含まれる内容の要旨
DECORATION • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles. 3 8 4 7 5 6 13 1
ページ14に含まれる内容の要旨
2 20 17 RIGHT SIDE VIEW 1 21 16 LEFT SIDE VIEW P9723b-0920 14
ページ15に含まれる内容の要旨
BATTERY INSTALLATION ® IMPORTANT! Use only a Power Wheels 12 volt lead-acid rechargeable battery. Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least 18 Battery Retainer ® hours using the enclosed Power Wheels 12 volt charger before operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. Never charge the battery longer than 30 hours. Failure to follow these instructions may damage
ページ16に含まれる内容の要旨
BATTERY CARE AND DISPOSAL Disposal Care If a battery leak develops, avoid contact with the leaking acid ® • Your Power Wheels battery is a non-spillable, sealed and place the damaged battery in a plastic bag. See information lead-acid battery. It must be recycled or disposed of in an below for proper disposal. environmentally sound manner. If acid comes in contact with skin or eyes, flush with cool • Do not dispose of a lead-acid battery in a fire. The battery water for at least 15 minutes
ページ17に含まれる内容の要旨
SAFE DRIVING RULES Teach Safety Rules to Children RIDING HAZARD While children can quickly develop the skill necessary to drive this vehicle, it is important to remember that their judgment skills WARNING are still very immature. Unsupervised driving by children can lead to serious injury. Before children use this vehicle, an adult should carefully evaluate the driving area as well as the children’s • Prevent Injuries and Deaths skill level and ability to drive this vehicle safely. Childre
ページ18に含まれる内容の要旨
VEHICLE OPERATION As assembled, your vehicle is ready to roll in low speed (2½ mph, maximum). It has been pre-set so it will only operate in low speed. After your child has mastered the basic skills of driving and understands the rules for safe driving, it’s time to connect the high speed connectors to allow the vehicle to operate in high speed. See the instructions on this page to connect the high speed connectors and operate the vehicle at high speed. Beginner Use - Low Speed Advanced Use -
ページ19に含まれる内容の要旨
VEHICLE CARE • Check all screws, cap nuts and their protective coverings • Avoid operating the vehicle on sand. Sand in the motors or regularly and tighten as required. Check plastic parts on electrical switches can cause them to jam, and could cause a regular basis for cracks or broken pieces. switch or motor failure. • During snowy or rainy weather, the vehicle should be stored • The vehicle can be wiped down with a soft, dry cloth. For a shiny inside or under a protective cover. Remember t
ページ20に含まれる内容の要旨
PROBLEMS AND SOLUTIONS IMPORTANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience ® ® a problem, please contact Power Wheels Consumer Relations, toll-free at 1-800-348-0751. Or, contact your local Power Wheels authorized service center. For the location nearest you, please visit us on-line at www.powerwheels.com, or call 1-800-348-0751. PROBLEM POSSIBLE CAUSE SOLUTION Vehicle does not run Undercharged battery Charge the
