Enviro EF2の取扱説明書

デバイスEnviro EF2の取扱説明書

デバイス: Enviro EF2
カテゴリ: クッカー
メーカー: Enviro
サイズ: 3.32 MB
追加した日付: 8/17/2014
ページ数: 40
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスEnviro EF2の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Enviro EF2に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Enviro EF2をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Enviro EF2のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Enviro EF2の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Enviro EF2 取扱説明書 - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Enviro EF2を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Enviro EF2の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
PELLET STOVE
EF2
Freestanding, Fireplace Insert
& Built-In Heater
OWNER’S MANUAL
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION
AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO
FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY
DAMAGE, BODILY INJURY, OR EVEN DEATH.
Contact your building or fire officials about restrictions and

ページ2に含まれる内容の要旨

Table of Contents Introduction...................................................................................................................................3 Pellet Quality..........................................................................................................................3 Rating Label Location..............................................................................................................3 Important Safety Data.............................................

ページ3に含まれる内容の要旨

Introduction PELLET QUALITY: Pellet quality is important, please read the following: Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other type of fuel, as this will void any warranties stated in this manual. The performance of your pellet stove is greatly affected by the type and quality of wood pellets being burned. As the heat output of various quality wood pellets differs, so will the performance and heat output of the pellet stove. CAUTION: It is impo

ページ4に含まれる内容の要旨

Introduction IMPORTANT SAFETY DATA: Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Contact your local building or fire official to obtain a permit and any information on installation restrictions and inspection requirements for your area. To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the instal

ページ5に含まれる内容の要旨

Introduction ASHES: Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be on a non-combustible floor on the ground, well away from all combustible materials pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispensed, they should be retained in the closed container until all cinders have been thoroughly cooled. ELECTRICAL: The use of a surge protected power bar is recommended. The unit m

ページ6に含まれる内容の要旨

Operating Instructions AUTOMATIC SAFETY FEATURES: Your pellet Stove has the following safety features: A. The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F (49°C). B. The stove has a high temperature safety switch. If the temperature on the hopper reaches 200°F (93°C), the auger will automatically stop and the stove will shut down when the exhaust temperature cools. If this happens, call your local dealer to reset the 200°F (93°C) high limit switch.

ページ7に含まれる内容の要旨

Operating Instructions OPERATING YOUR PELLET STOVE: 1. Check and fill hopper with pellets. 2. Make sure unit is plugged into a working outlet. C o n v e c t i o n B l o w e r S p e e d C o n t r o l 3. Switch the power on by pushing the ROCKER SWITCH to the K n o b A MANUAL position. 4. Turn KNOB B to the 12 o’clock position. (Lower grade pellets may need a higher setting on the feed rate). G r e e n L i g h t NOTE: Unit will take longer to light if the hopper has been ( A u g e r L i g h

ページ8に含まれる内容の要旨

Routine Cleaning and Maintenance NOTE: Do not use abrasive cleaners to clean the surface or any part of the stove. The following should be inspected periodically to ensure that the appliance is operating at its optimum and giving you excellent heat value: TOOLS REQUIRED TO CLEAN UNIT • Torx T-20 Screwdriver 2-3 Days / Weekly Biannually or 2 Tons of Fuel 5 • /16” Wrench or Socket, Burn Pot and Liner Exhaust Vent • Brush, Ash Pan Fresh air Intake Tube • Soft Cloth Inside Firebox Blower Mechanism

ページ9に含まれる内容の要旨

Routine Cleaning and Maintenance ASH PAN (2-3 days) Monitor the ash level every week. Remember that different pellet fuels will have different ash contents. Ash content is a good indication of fuel efficiency and quality. Dump the ashes into a metal container stored away from combustibles. Refer to “Warnings and Recommendations” for disposal of ashes. DO NOT PLACE UNBURNED OR RAW PELLET FUEL IN ASH PAN. Vacuum the ash pan and inside the pedestal. CAUTION: BECAUSE THE FLY ASH IS VERY FINE, TH

ページ10に含まれる内容の要旨

Routine Cleaning and Maintenance Installation of firebox backing: • Install the side panels in place. Insert center panel, hold the panels in place • Install the top rod by sliding it into one side panel then across into the other panel. Screw rod in place. • Re-install steel brick liner and screw in place. • Replace top baffle EXHAUST VENT (season) The products of combustion will contain small particles of flyash. The flyash will collect in the exhaust venting system and restrict the flow o

ページ11に含まれる内容の要旨

Installation DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE: 1. Check clearances to combustibles. 2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be obtained from a ventilated crawlspace. 3. Do not install the stove in a bedroom. 4. You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry or metal chimney (must be lined if the chimney is over 6” (15 cm) diameter, or over 28 inches² (180 cm²) c

ページ12に含まれる内容の要旨

Installation DIMENSIONS - FREESTANDING: � � � � � � � � � � �� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � Figure 7: Dimensions of EF2 Freestanding. DIMENSIONS - FIREPLACE INSERT AND BUILT-IN HEATER: � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � Figure 8: Dimensions of EF2 Fireplace Insert and Built-I

ページ13に含まれる内容の要旨

� � � � � � � � � � � � Installation CLEARANCES TO COMBUSTIBLES - FREESTANDING: When installing this unit on a combustible floor (for example linoleum, hardwood flooring) a non- combustible hearth pad must be under the unit. The pad must extend at least the width of the appliance [22” (558 mm)] and at least the depth of the appliance plus 6” (153 mm) in front of the appliance [29 3⁄4” (756 mm)]. These dimensions are minimum clearances but it is Side wall to unit - 6 inches (15 cm) recommend

ページ14に含まれる内容の要旨

Installation CLEARANCES TO COMBUSTIBLES - BUILT-IN HEATER: 33 " Refer to Figures 11 and 12. ( 8 4 c m ) 1 2" ( 30 .5 c m ) Side wall to unit - 8 inches (20.3 cm) Mantel projection - 10 inches (25.4 cm) Mantel to top of unit - 8 inches (20.3 cm) Top facing to unit - 8 inches (20.3 cm) Side facing to unit - 6 inches (15.2 cm) 30 " ( 7 6 cm ) Floor protection - 6 inches (15.2 cm) (on either side and to the front must be protected by non-combustible material) 6 " Sides and rear walls to stand

ページ15に含まれる内容の要旨

Installation VENT TERMINATION REQUIREMENTS: IT IS RECOMMENDED THAT YOUR PELLET STOVE BE INSTALLED BY AN AUTHORIZED DEALER/INSTALLER. Table 1: Use in conjunction with Figure 16 for allowable exterior vent termination locations. Letter Minimum Clearance Description A 24 in (61 cm) Above grass, top of plants, wood, or any other combustible materials. B 48 in (122 cm) Beside/below any door or window that may be opened. (18” (46 cm) if outside fresh air install.) C 12 in (30 cm) Above any door o

ページ16に含まれる内容の要旨

Installation OUTSIDE FRESH-AIR CONNECTION: Outside fresh air is mandatory when installing this � � � � � � � unit in airtight homes and mobile homes. � � � � When connecting to an outside fresh air source, do not use plastic or combustible pipe. A 15⁄8” minimum (42 mm) ID (inside diameter) steel, aluminum or copper pipe should be used. It is recommended, when you are installing a fresh � � � � � � � � � � � � � � � air system, to keep the number of bends in the pipe to a � � � � � � �

ページ17に含まれる内容の要旨

Installation MOBILE HOME INSTALLATION - FREESTANDING: ● Secure the heater to the floor using the (2) two holes in the pedestal. ● Ensure the unit is electrically grounded to the chassis of your home (permanently). ● Do not install in a room people sleep in. ● Outside fresh air is mandatory. Secure outside air connections EN VIR O E F 2 directly to fresh air intake pipe and secure with three (3) screws evenly spaced. H E A R T H P A D F L O O R I N G ST EE L F R A ME G R O U N D W I R E

ページ18に含まれる内容の要旨

Installation HORIZONTAL EXHAUST THROUGH WALL INSTALLATION - FREESTANDING: Vent installation: install vent at clearances specified by the vent manufacturer. A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces, or a floor, or ceiling. Where passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365 Installation Code for Solid-Fuel-Burning Appliances and Equipment. Only use venting o

ページ19に含まれる内容の要旨

Installation 10. The pipe must extend at least 12” (30 cm) away from the building. If necessary, bring another length of pipe (PL type) to the outside of the home to connect to the first section. Do not forget to place high temperature silicone around the pipe that passes through the thimble. 11. Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The stainless steel cap termination manufactured by the vent manufacturer is recommended. However

ページ20に含まれる内容の要旨

Installation INSIDE VERTICAL INSTALLATIONS - FREESTANDING: 1. Choose a stove location that is ideal. See the section “DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE.” 2. Place a non-combustible hearth R a i n ca p pad where necessary. 3. Place the unit on the hearth pad F l a sh i n g (if installed on a carpeted surface) 2 4 " and space the unit in a manner so ( 6 1 cm ) when the pellet vent is installed vertically, it will be 3” (7.6 cm) away from a combustible wall. 3 " ( 7 .5 cm ) cl


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Enviro 50-1095 取扱説明書 クッカー 1
2 Enviro 50-1220 取扱説明書 クッカー 3
3 Enviro 50-1096 取扱説明書 クッカー 0
4 Enviro 50-1266 取扱説明書 クッカー 0
5 Enviro 50-1221 取扱説明書 クッカー 1
6 Enviro 2100 Freestanding 取扱説明書 クッカー 0
7 Enviro 50-1574 取扱説明書 クッカー 0
8 Enviro 50-1675 取扱説明書 クッカー 0
9 Enviro 50-1385 取扱説明書 クッカー 0
10 Enviro 50-1386 取扱説明書 クッカー 0
11 Enviro 50-1573 取扱説明書 クッカー 0
12 Enviro 1700-V Insert 取扱説明書 クッカー 0
13 Enviro BERN C-10629 取扱説明書 クッカー 0
14 Enviro C-10365 取扱説明書 クッカー 0
15 Enviro C-10608 取扱説明書 クッカー 0
16 Edelbrock 2006-2007 (N) 取扱説明書 クッカー 4
17 Aarrow Fires SF 50 取扱説明書 クッカー 1
18 Aarrow Fires EcoBurn BK043 取扱説明書 クッカー 0
19 Aarrow Fires EcoBurn AFS1221 取扱説明書 クッカー 0
20 Aga Ranges Berrington 取扱説明書 クッカー 3