ページ1に含まれる内容の要旨
1
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
CERTIFIED UNDER AMERICAN NATIONAL STANDARDS, ANSI Z21.11.2b, VOLUME II FOR UNVENTED ROOM HEATERS.
UNVENTED MILLIVOLT SYSTEM
INSTALLATION AND OPERATION INSTRUCTIONS FOR
UNVENTED GAS FIREPLACE
NATURAL GAS MODEL GVFS60-N
PROPANE GAS MODEL GVFS60-P
CERTIFIED FOR THE UNITED STATES USING ANSI / AGA METHODS
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing
ページ2に含まれる内容の要旨
2 TABLE OF CONTENTS PG 3-4 INTRODUCTION PG 9 BLOWER INSTALLATION Warranty 10-11 OPERATION / MAINTENANCE General Instructions Operating Instructions Shipping Bracket Maintenance Mobile home installation Oxygen Depletion Sensor Pilot Cleaning General Information Venturi Adjustment 5 LOCATIONS & CLEARANCES 12 REPLACEMENTS 5-7 INSTALLATION Ordering Replacement Parts Combustion and Ventilation Air Provisions Replacement Parts Installation Examples Accessories Gas Installation 13-14 TROUBLE SHOOTING G
ページ3に含まれる内容の要旨
3 NAPOLEON gas fireplaces are manufactured under the strict Standard of the world recognized ISO9002 Quality Assurance Certificate. NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. The burner and valve assembly are leak and test-fired at a quality test station. The complete fireplace is test-fired and thoroughly inspected by a qualified technician before packaging to ensure that you, the customer, receives t
ページ4に含まれる内容の要旨
4 GENERAL INSTRUCTIONS MOBILE HOME INSTALLATION THIS GAS FIREPLACE SHOULD BE INSTALLED AND Suitable for mobile home installation where the mobile SERVICED BY A QUALIFIED INSTALLER to conform with home has been permanently placed on its site. local codes. In absence of local codes, install the GVFS60 This fireplace may be installed in an aftermarket per- to the current National Fuel Gas Code, ANSI Z223.1 In- manently located, manufactured (mobile) home, where stallation Code which can be obtaine
ページ5に含まれる内容の要旨
5 LOCATION AND CLEARANCES Provide adequate ventilation and combustion air. MAINTAIN THESE MINIMUM CLEARANCES TO COMBUSTIBLES: Provide adequate accessibility clearance for servic- ing and operating the stove. Never obstruct the front opening of the stove. As long as clearance to combustibles is kept within the required distances, the most desirable and beneficial lo- cation for a Napoleon stove is in the centre of a building, thereby allowing the most efficient use of the heat created. The locati
ページ6に含まれる内容の要旨
6 Room Volume = Length x Width x Height Max BTU/hr = Room Volume x 1000 ÷ 50 ROOM 2 ROOM 1 FIGURE 4 HEIGHT HEIGHT HEIGHT HEIGHT HEIGHT If for example, the length of the rooms is 10 feet, the width of Room 1 is 10 feet, LENGTH LENGTH LENGTH LENGTH LENGTH the width of Room 2 is 15 feet the height of the rooms is 8 feet. The volume of Room 1: 10 x 10 x 8 = 800 cubic feet. The volume of Room 2: 10 x 15 x 8 = 1200 cubic feet. Unusually tight construction is defined as con- struction where: EXAMPLE
ページ7に含まれる内容の要旨
O H L I L I O L P P F F O 7 4. For ease of accessibility, an optional remote wall GAS INSTALLATION switch or millivolt thermostat may be installed in a con- venient location. Route a 2 strand, solid core millivolt wire 1. Move the stove into position. We recommend secur- from the stove to the wall switch or millivolt thermostat. ing the stove to the floor, in all cases. Levelling / securing The recommended maximum lead length depends on kit GDSLL-KT may be used for this purpose. wire size: 2. I
ページ8に含まれる内容の要旨
8 The notch in log #5 should be pressed down onto the LOG PLACEMENT INSTRUCTIONS skewering pin located at the end of the grate as shown to Blocked burner ports can cause an incorrect flame pat- TM prevent it from rocking. tern, carbon deposits and delayed ignition. PHAZER logs glow when exposed to direct flame and provide a unique 3 TM and realistic glowing effect. Use only certified PHAZER logs available from your Napoleon / Wolf Steel Ltd. dealer. #6 FIGURES 8a-d 1 #1 #3 Position the notch loc
ページ9に含まれる内容の要旨
9 BLOWER INSTALLATION ON/OFF SWITCH BRACKET 4. Remove the 2 screws from the top outer edge of the rear stove panel. The housing is mounted using these two COVER PLATE holes, as well as two other holes located in the rear panel. 5. Mount and secure the blower housing using 4 screws. Ensure that the on/off switch wires pass through the appro- priate slot located on either side of the blower housing. 6. Remove the 2 screws from the side of the blower housing that you want the switch to be located o
ページ10に含まれる内容の要旨
O H L I L I I O L P P F F O N O T O 10 OPERATION / MAINTENANCE OPERATING INSTRUCTIONS If heater shuts off, do not relight until you provide When lit for the first time, the fireplace will emit a slight fresh air. If heater keeps shutting off, have it serv- odour for a few hours. This is a normal temporary condi- iced. Keep burner and control compartment tion caused by the curing of the logs and the "burn-in" of internal paints and lubricants used in the manufacturing clean. process and will not
ページ11に含まれる内容の要旨
11 MAINTENANCE OXYGEN DEPLETION SENSOR PILOT CLEANING TURN OFF THE GAS AND ELECTRICAL POWER This procedure must be performed by a qualified BEFORE SERVICING THE FIREPLACE. service person! CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and Inspect the pilot for any visible contamination or debris dangerous operation. Verify proper operation after servic- (usually lint, pet hair, spider webs, carpet fibre, etc.) and ing. This heater should
ページ12に含まれる内容の要旨
O H L I L I O L P P F F O 12 REPLACEMENTS ORDERING REPLACEMENT PARTS Contact your dealer or the factory for questions concern- ing prices and policies on replacement parts. Normally all W725-030 parts can be ordered through your Napoleon dealer or W725-031 distributor. When ordering replacement parts always give the following information: 1. MODEL & SERIAL NUMBER OF FIREPLACE 2. INSTALLATION DATE OF FIREPLACE 3. PART NUMBER 4. DESCRIPTION OF PART 5. FINISH W361-0016 REPLACEMENT PARTS For war
ページ13に含まれる内容の要旨
13 TROUBLE SHOOTING GUIDE SYMPTOM PROBLEM TEST SOLUTION Main burner goes Pilot flame is not large - service or replace Oxygen Depletion Sensor System out; pilot stays on. enough or not engulfing the - correct piping and/or regulator to provide correct pressure thermopile Thermopile shorting - clean thermopile connection to the valve. Reconnect. - replace Oxygen Depletion Sensor System / valve. Remote wall switch wire is - shorten wire to correct length or wire gauge. too long; too much resis-
ページ14に含まれる内容の要旨
O H L I L I O L P P F F O 14 SYMPTOM PROBLEM TEST SOLUTION Pilot goes out Gas piping is undersized. - turn on all gas appliances and see if pilot flame flutters, dimin- while standing; ishes or extinguishes, especially when main burner ignites. Monitor Main burner is in appliance supply working pressure. 'OFF' position. - check if supply piping size is to code. Correct all undersized piping. Flames are con- Unit is over-fired or under- - check pressure readings: sistently too large fired. Inl
ページ15に含まれる内容の要旨
15 W415-0204 / C / 10.02.01 Wolf Steel Fireplace Service History This fireplace must be serviced annually depending on usage. Service Technician Date Dealer Name Service Performed Special Concerns Name
ページ16に含まれる内容の要旨
16 NOTES: W415-0204 / C / 10.02.01
