ページ1に含まれる内容の要旨
ShadowLight XL
Direct Vent Gas Fireplace Insert
Owners Manual
R2
8/06
WARNING: If the information in this manual is not followed ADVETISSEMENT: Quinconque ne respect pas à la
exactly, a fire or explosion may result causing property lettre les instructions dans le présent manuel risque de
damage, personal injury or loss of life. déclencher un incendie ou une explosion entraíant des
dommages matérials, des lésions corporelles ou la perte
Installation and service must be performed by a qualifie
ページ2に含まれる内容の要旨
2 WARNING: If the information in this manual is ADVETISSEMENT: Quinconque ne respect pas not followed exactly, a fire or explosion may result à la lettre les instructions dans le présent manuel causing property damage, personal injury or loss risque de déclencher un incendie ou une explosion of life. entraíant des dommages matérials, des lésions corporelles ou la perte de vies humaines. Installation and service must be performed by a qualified installer, service agency, or the gas sup- L’i
ページ3に含まれる内容の要旨
3 TABLE OF CONTENTS INTRODUCTION ...........................................................4 SPECIFICATIONS .........................................................5 OPERATION ...................................................................8 How to Light the Fire ................................................9 How to Turn Off the Fire .........................................10 INSTALLATION ........................................................... 11 Clearances .....................
ページ4に含まれる内容の要旨
4 Introduction The installation of the ShadowLight XL Fireplace Insert must conform with local codes, or in the absence of local codes, with National Fuel Gas Code, ANSI Z233.1 (NFPA 54). Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les Listed Direct Vent Gas Fireplace Heater Codes d'installation CAN/CGA-B149. Radiateur Ventile The ShadowLight XL Fireplace Insert may be installed Model: ShadowLight XL Gas Fireplace Insert • Homologue
ページ5に含まれる内容の要旨
5 Specifications 40” 30” Front View Minimum Opening Size: 29” Inlet Outlet 14” Top View 13” Side View Front View
ページ6に含まれる内容の要旨
Specifications 6 On-Off- Thermostat Switch Glass Door Face Bolt Pilot Burner Burner Plate Face Bolt Leveling Bolt Hi-Low Knob Latch Handle Lighting On-Off-Pilot Instructions Knob Safety Label Igniter Blower Speed Switch Leveling Bolt
ページ7に含まれる内容の要旨
7 Specifications Air Intake Vent On-Off Thermostat Switch On-Off Thermostat Switch Connector Leveling Bolt RATINGS NATURAL PROPANE Input Rating (Btu/hr)(0-2,000 ft)(0-610m) 35,000 BTU 35,000 BTU Input Rating(Btu/hr)(2000-4500ft)(610-1375m) 34,000 BTU 34,500 BTU Min. Input Rating (Btu/hr) 21,600 BTU 20,900 BTU Orifices (DMS)(0-2000 ft)(0-610m) 31 50 Orifices (DMS)(2000-4500ft)(610-1375m) 33 51 Manifold Pressure (i
ページ8に含まれる内容の要旨
8 Operation Warning Doors Are Hot While In Operation. Wear Gloves PILOT and Only Touch Doors On The Handles. Pilot Location Shown Above Door Handles ON-OFF/ Lift bottom grill with index THERMOSTAT finger and fold down to Switch access controls ON OFF THERMOSTAT ● Pull lighting instruction UP - ON Piezo Igniter plate out to view text. MIDDLE - OFF Button ● Push back in before Blower Speed DOWN - THERMOSTAT closing grills. Switch
ページ9に含まれる内容の要旨
9 Operation Operation HOW TO LIGHT THE FIRE 1. STOP! Read the safety information on the front cover. 2. If using the optional thermostat, set thermostat to High-Low the lowest setting. 3. Turn off electric power to the appliance. 4. Turn the ON-OFF/THERMOSTAT switch to the OFF position. 5. Push in the gas control knob slightly and turn it clockwise to “OFF.” NOTE: THE KNOB CANNOT BE TURNED FROM “PILOT” TO “OFF” UNLESS IT IS PUSHED IN SLIGHTLY. DO NOT FORCE IT. 6. Wait five (5) m
ページ10に含まれる内容の要旨
10 Operation 15. Set the High-Low Regulator to desired setting: Turn fully counterclockwise for High and fully clockwise for Low. NOTE: An odor, resulting from the initial heating of new materials in your heater, is not unusual during the first fire, and in most cases will disappear after an hour or two. HOW TO TURN OFF THE FIRE 1. If using optional thermostat, set thermostat to the lowest position. Air Shutter 2. Turn off the electric power to the appliance. Adjustment 3. Turn the ON-OFF
ページ11に含まれる内容の要旨
11 Only For Qualified Installers Installation Packing List Inside the Insert Box Inside Face Box ShadowLight XL Insert ShadowLight XL Face Log set Right Door Bag of rock wool Left Door Owners Manual Hardware Pack Restrictor Plates
ページ12に含まれる内容の要旨
Only For Qualified Installers 12 Installation Installation “In the Commonwealth of Massachusetts, this product must be installed by a licensed Massachusetts Plumber or Gas Fitter” Due to high temperatures, the ShadowLight XL Fireplace Insert should be located out of traffic and away from furniture and draperies. Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition. Young children should be carefully supervi
ページ13に含まれる内容の要旨
13 Only For Qualified Installers Installation Making The Connection The gas inlet is located on the bottom right side of the fireplace. The inlet fitting is 1/2” male flare fitting designed for 1/2” stainless flex pipe. This fitting can be removed to provide 3/8” female pipe thread. A separate gas shut-off valve and a 1/8” N.P.T. plugged tapping should be installed immediately up- stream of the connection to the appliance. The ShadowLight XL Direct Vent Gas Heater must be disconnected from the gas
ページ14に含まれる内容の要旨
Only For Qualified Installers 14 Installation Converting to Natural Gas Cer equipenent de conversion sera installe par une “This conversion kit shall be installed by a qualified agence qualifiee de service conformement aux instruc- service agency in accordance with the manufacturer’s tions du fabricant et toutes exigencies et codes appli- instructions and all applicable codes and requirements cables de l’autorises avoir la jurisdiction. Si l’information of the authority having jurisdiction.
ページ15に含まれる内容の要旨
15 Only For Qualified Installers Installation Converting to Natural Gas Door Hooks 3 1 Remove air plate by lifting it up about 3 inches and then out of firebox. Be careful not to damage side Door Latches brick panels 4 Remove door by pulling latches out as shown and pulling the bottom of the door out from the unit about 3”. Then lift the door slightly up and off the hooks. 2 Remove the screws mounting the intake air deflector and lift it from the firebox. Next locate the screw holding the bur
ページ16に含まれる内容の要旨
Only For Qualified Installers 16 Installation 5 Remove three screws to change knob assembly. Install NG knob assembly in place of the LP assembly. Be sure screws are tight. 6 Place conversion sticker (provided in Kit) on the valve. This is to permanently mark the valve that it has been converted to Natural Gas. This label is important in the event that the valve is ever removed and mixed in with other valves. Reassemble all components removed during the conversion process. 7 Mark the proper
ページ17に含まれる内容の要旨
17 Specifications Converting to High Altitude Door Hooks 3 1 Remove air plate by lifting it up about 3 inches and Door Latches then out of firebox. Be careful not to damage side brick panels 4 Remove door by pulling latches out as shown and pulling the bottom of the door out from the unit about 3”. Then lift the door slightly up and off the hooks. 2 Remove the screws mounting the intake air deflector and lift it from the firebox. Next locate the screw holding the burner tube to the firebox flo
ページ18に含まれる内容の要旨
Only For Qualified Installers 18 Installation Venting Preliminary steps to prepare for the installation of the ShadowLight XL Fireplace Insert Remove the chimney cap if one exists so that the flue may be cleaned and the venting installed. Remove any existing hearth accessories such as glass doors, spark screens, andirons, and grates. Clean the chimney thoroughly to remove ash, soot, and any obstructions, and then clean ash, soot, dust, and debris from the fireplace. The damper must be locked
ページ19に含まれる内容の要旨
19 Only For Qualified Installers Installation A bead of silicone goes Use Only Approved Venting between the top of This appliance has been tested and is listed for the tile liner and the installation with Simpson Duravent GS and Duraflex flashing to seal the cap AL venting components. The warranty will be voided, to the chimney Flashing and serious fire, health, or other safety hazards may result from any of the following actions: Tile Liner • Installation of any damaged Simpson Duravent c
ページ20に含まれる内容の要旨
Only For Qualified Installers 20 Installation Venting and Installation 1 3 Feed chimney liners down the chimney and through Remove the screw, washer and spacer from the the damper.If the fireplace opening does not allow center of the rear brick panel. Using one hand, enough room to connect the flue liners to the stove gently push out on the side brick /relief door to allow it is necessary to separate the exhaust/ intake pipe clearance for removing the rear brick panel. adapter from the sto
