ページ1に含まれる内容の要旨
3-SIDED (PENINSULA), VENTED DECORATIVE GAS APPLIANCE
OWNER’S OPERATION AND INSTALLATION MANUAL
MARBLEHEAD
NATURAL GAS MODELS GL36PN AND GL36PNE
PROPANE/LP GAS MODELS GL36PNP AND GL36PNEP
WARNING: If the information in these instructions is
not followed exactly, a fire or explosion may result
causing property damage, personal injury or death.
FOR YOUR SAFETY
— Do not store or use gasoline or any other flammable
vapors or liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YO
ページ2に含まれる内容の要旨
WARNING: Improper installation, adjustment, altera- tion, service or maintenance can cause injury or prop- erty damage. Refer to this manual for correct installation and operational procedures. For assistance or addi- tional information consult a qualified installer, service agency or the gas supplier. NOT FOR USE WITH SOLID FUEL CHECK LOCAL CODES PRIOR TO INSTALLATION SAVE THIS BOOK This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also co
ページ3に含まれる内容の要旨
1. This appliance is only for use with the type SAFETY INFORMATION of gas indicated on the rating plate. This ap- pliance is not convertible for use with other WARNING: This product gases. contains and/or generates 2. For propane/LP fireplace, do not place propane/ chemicals known to the State LP supply tank(s) inside any structure. Locate of California to cause cancer or propane/LP supply tank(s) outdoors. To prevent birth defects or other reproduc- performance problems, do not use prop
ページ4に含まれる内容の要旨
16. Do not install fireplace directly on carpeting, SAFETY INFORMATION vinyl tile or any combustible material other Continued than wood. The fireplace must set on a metal 11. Keep the area around your fireplace clear of or wood panel extending the full width and combustible materials, gasoline and other depth of the fireplace. flammable vapor and liquids. Do not run fire- 17. Do not use fireplace if any part has been ex- place where these are used or stored. Do not posed to or under water. Immed
ページ5に含まれる内容の要旨
This appliance complies with ANSI Z21.50B-1990 INTRODUCTION and CAM/CGA-2.22-M89 as a Vented Gas Ap- Models GL36PN/P and GL36PNE/P are decora- pliance and is listed and tested by the Omni Test tive gas appliances that use a millivolt gas control Laboratories. and piezo pilot or an electronic gas control valve with an electronic ignition system respectively. WARNING: Installation of These systems require a 6", B-type venting system this appliance should be done by for operation. a qualifi
ページ6に含まれる内容の要旨
1" Minimum SELECTING LOCATION 1" Minimum Clearance from Pipes Clearance to Combustibles to Combustibles Continued In selecting a location, the following precautions 3 22 / " 4 must be observed: 19" 1. Do not connect this appliance to a chimney 3 11 / " 8 system used for a solid fuel burning fire- place. 5 2. Install in an area providing ventilation and 21 / " 8 6" O.D. adequate combustion air. 4" Min. from the Perpendicular Side Wall to the Fireplace Opening (Typ.) 3. Due to high temperatures,
ページ7に含まれる内容の要旨
3 40 /8" FIREPLACE 1" Min. to Combustibles INSTALLATION Continued Nailing Flanges FRAMING Construct framing using dimensions shown if Figures 6, 7 and 8. (Use the figure applicable to your applica- Prepared Framing tion.) Figure 6 shows the framing dimensions prior to having the appliance in place. If installing on a platform, platform must be solid, flat and fully sup- Nails or Screws ported (see Figure 7). Once the unit has been fitted, bring studs in against nailing flanges located on the s
ページ8に含まれる内容の要旨
T FIREPLACE CAUTION: Do not connect INSTALLATION this millivolt system wall switch Continued to a regular 120v power source! OPTIONAL OUTSIDE AIR KIT Gas valve be damaged - will be (MODEL AK4) yond repair. The installation of an outside air kit should be completed during the rough framing of the fire- Wall Switch Installation place due to the nature of it's location. Outside 1. Remove the J-box cover plate from side of combustion air is accessed through a vented applianceʼs outer surro
ページ9に含まれる内容の要旨
A E The gas control valve is secured to the burner pan FIREPLACE assembly underneath the front ledge. A 1/8" NPT INSTALLATION plugged tapping is provided on the gas control Continued valve for a test gauge connection immediately upstream of the gas supply connection to the ap- pliance (see Figures 13 and 14). Pilot Gas Line Do Not Kink Pilot To Pilot Adjustment Burner ON/OFF Cap Knob To Main Burner Strain Relief Grommet Common Ground Wire Inlet Outlet Pressure Pressure Figure 12 -
ページ10に含まれる内容の要旨
Shutoff FIREPLACE Key Valve INSTALLATION Continued To install: 1. Remove gas line cover plate from applianceʼs outer surround at the location to be used. 2. Remove insulation from inside the gas line Extension conduit sleeve. 3. Run gas line through sleeve. Typical Exterior Wall Gas 4. Prepare incoming black iron gas line with Shutoff Installation Teflon tape or pipe joint compound. (Check Figure 15 - Typical Exterior Wall Gas local codes as to the use of Teflon tape.) Shut-Off Installation
ページ11に含まれる内容の要旨
FIREPLACE Pilot Burner Ignitor Flame INSTALLATION 1/8" to 1/4" Sensor Continued 3/8" to 1/2" Noncombustible Facing Material Pan Burner Do Not Block Effective Opening Figure 19 - Correct Pilot Flame Pattern "L" Shaped Metal Support - Electronic Assembly Noncombustible Facing Material BURNER FLAME ADJUSTMENT The air shutter, located at the base of the main burner tube, has been factory preset to the proper air to bas ratio which results in a long, blue, cleaner Figure 17 - Fireplace Fa
ページ12に含まれる内容の要旨
Top Slot FIREPLACE Under Frame INSTALLATION Adjustment Continued Clip OPTIONAL GLASS DOOR Adjustment Glass doors are optional with this gas appliance (see Screw Replacement Parts and Accessories, page 19). Long Pivot Pin Installing Glass Door 1. Be sure top spring clip hole is aligned with hole in fireplace frame (see Figure 21). Fit glass door top pin into aligned holes. Bottom Pin 2. Swing inner end of bottom clip out away from Bottom Slot fireplace frame. Fit door bottom pin into clip. A
ページ13に含まれる内容の要旨
1. STOP! Read the safety information, OPERATING FIREPLACE column 1. MILLIVOLT MODELS 2. Turn wall switch to the OFF position. 3. Turn off all electric power to the appliance. FOR YOUR SAFETY 4. Open control access panel. READ BEFORE LIGHTING 5. Push in gas control knob and turn clock- wise to the OFF position (see WARNING: If you do not fol- Figure 23). Note: It is recommended that low these instructions exactly, you maintain the gas control knob in the a fire or explosion may result fu
ページ14に含まれる内容の要旨
E A C. Use only your hand to push in or turn the OPERATING FIREPLACE gas control knob. Never use tools. If the Continued knob will not push in or turn by hand, donʼt try to repair it, call a qualified service tech- TO TURN OFF GAS nician or gas supplier. Force or attempted TO APPLIANCE repair may result in a fire or explosion. 1. Turn off the wall switch. D. Do not use this appliance if any part has 2. Turn off all electric power to the appliance been under water. Immediately call a if
ページ15に含まれる内容の要旨
OPERATING FIREPLACE WARNING: Turn off gas and Continued electrical power before servicing appliance. Any safety screen or guard removed for servicing must be replaced prior to operat- ing the appliance. WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in Figure 26 - Pilot sooting and property damage. Keep control compartment, logs, burner and area TO TURN OFF GAS surrounding logs clean by vacuuming or brushing TO APPLIANCE at least twice a year. T
ページ16に含まれる内容の要旨
MV TH PV/MVTR GND PV IGN O WIRING DIAGRAMS PILOT THERMOPILE IGNITOR DO NOT CONNECT TO 120V N.C.SW HEAT LIMIT SWITCH TH TP TH/TP INCOMING MAIN GAS SUPPLY PILOT SAFETY WIRE WALL SWITCH (SUPPLIED) MILLIVOLT WIRING DIAGRAM PILOT INCOMING IGNITOR WALL SWITCH MAIN GAS (SUPPLIED) SUPPLY SENSOR BLACK INCOMING 120V AC WHITE (FUSE BOX GREEN OR BREAKER) N.C.SW HEAT LIMIT EV1 SWITCH ELECTRICAL RATING: 120v, 60Hz, 0.7A EV2 24V AC STEP DOWN TRANSFORMER 120V AC OPTIONAL REMOTE GAS LINE CONTROL TO BURNER ELE
ページ17に含まれる内容の要旨
TROUBLESHOOTING MILLIVOLT SYSTEM Note: Before troubleshooting the system, make sure the gas shutoff valve is ON. The two most common causes of a malfunctioning gas appliance are: 1. Loose wiring connections 2. Construction debris clogging the pilot and/or gas control valve filter OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Pilot will not light 1. No gas supply or shutoff 1. Check to see if you have gas valve is OFF supply 2. Air in gas line 2. Hold regulator control valve in the PILOT position for
ページ18に含まれる内容の要旨
TROUBLESHOOTING ELECTRONIC IGNITION SYSTEM Note: Before troubleshooting the system, make sure the gas shutoff valve is ON. The two most common causes of a malfunctioning gas appliance are: 1. Loose wiring connections 2. Construction debris clogging the pilot and/or gas control valve filter OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Pilot will not light 1. No gas supply or shutoff 1. Check to see if you have gas valve is OFF supply 2. Construction debris clog- 2. Remove debris and dirt, in- ging pil
ページ19に含まれる内容の要旨
REPLACEMENT PARTS AND ACCESSORIES Purchase these fireplace replacement parts and BRUSHED BRASS CABINET STYLE accessories from your local dealer. If they can not DOOR KIT - DBBGL36PN supply these parts, call DESA at 1-866-672-6040 Right Panel Assy - 22367 for referral information. You can also write to the Left Panel Assy - 22368 address listed on the back page of this manual. End Panel Assy - 22369 Before ordering, please have your applianceʼs For use with all models. model name or number an
ページ20に含まれる内容の要旨
LIMITED 2-YEAR WARRANTY DESA warrants this gas appliance to be free from the defects in material or workmanship at the time of manufacture. REMEDY AND EXCLUSIONS The coverage of this warranty is limited to all components of the gas appliance manufactured by DESA, with the exception of glass and refractory. The glass is warranted for 90 days. There will be no cost for replacement of glass within 90 days of installation, provided that breakage is due to heat from the appliance. We do not warrant
