ページ1に含まれる内容の要旨
TM
JUNGLE MIST JUNIOR ANTI-DRIP
Operating Instructions
110VAC P/N 100072
12VDC P/N 100068
230VAC P/N 100074 (w/transformer)
ページ2に含まれる内容の要旨
TM ! Thank you for purchasing this Jungle Mist Junior Anti-Drip ! As you will notice from the table of contents, the manual for your new pump is quite extensive. To guarantee perfect and successful work with this machine, please take time to read the manual carefully. ! Do not operate before changing oil cap! ! And finally, we believe you will enjoy many years of dependable, trouble free service if you properly install and maintain your Jungle Mist Junior TM Anti-Drip
ページ3に含まれる内容の要旨
Contents 1. Equipment Supplied 3 2. Accessories and Parts 3 3. Safety information 4 4. Grounding Instructions 4 5. Receiving and Unpacking 5 5.1 Checking for Damage in Shipping 5.2 Checking Inventory of Parts 6. Hooking up the Pump 6 6.1 Installation of Pump 6.2 Water Supply 6.3 Water Filter Installation 6.4 Anti-Drip Extension 7. Mist Line Layout Strategies 7 7.1 Light, Medium or Heavy Haze 7.2 Indoor Fog Curtains 7.3 Raise Humidity to Keep Dust Down 7.
ページ4に含まれる内容の要旨
1. Equipment Supplied ! Jungle Mist Junior Anti-Drip System (Please see section 5.2 for a complete checklist.) 2. Accessories and Parts 100068 10 Nozzle Anti-Drip Pump Kit 12 VDC 250042 Universal DMX Relay 3-pin XLR, Heavy Duty 600720 Filter Housing with Bracket Kit 600721 5-Micron Sediment Filter Cartridge 600722 1.5" Automatic Drain Valve 600723 .008 Nozzle with 10/24 Thread 600724 .012 Nozzle with 10/24 Thread 600725 Push Connector Quick Device - Tee Onl
ページ5に含まれる内容の要旨
3. Safety Information 3.3 WARNING: Read through the entire instructions before attempting installation. • Risk of electrical shock - This pump is supplied with a grounding conductor. To reduce risk of electrical shock, connect only to a properly grounded, grounding type receptacle. • Plug the unit into a dedicated, fused circuit. • Install pump on a flat, level, solid foundation. This pump is non-submersible. 4.4 CAUTIONS: • Pump warranty is voided by failure to use factory-
ページ6に含まれる内容の要旨
5. Receiving and Unpacking 5.1 CHECKING FOR DAMAGE IN SHIPPING • Carefully examine contents for signs of damage in shipping. Immediately notify the carrier if damage is detected that was not visible upon receipt of shipment. 5.2 CHECKING INVENTORY OF PARTS TM Jungle Mist Junior P/N 100072 (12VDC P/N 100068) CITC ITEM# QTY PART DESCRIPTION Received 1 Pump Assembly, Chassis & Cover (check for correct voltage) 600717 110VAC model 600716 12VDC model Note
ページ7に含まれる内容の要旨
6. Hooking up the Pump 6.1 INSTALLATION OF PUMP • The pump should be set inside a covered area on a level surface such as a stage or platform. Do not set it on a soft surface as the vibration will sink the unit. 6.2 WATER SUPPLY • Insure that the water source being used can supply enough water for the demand of the pump. Use a minimum ¾” hose (19 mm) with at least 40 PSI (2.8 bar) of clean water. 6.3 WATER FILTER INSTALLATION • NOTE! Use factory-supplied water filter in w
ページ8に含まれる内容の要旨
6.4 ANTI-DRIP EXTENSION • With anti-drip, you can stop drips from occurring when stopping and starting the TM Jungle Mist Junior Anti-Drip . Each time you stop the system, the auto-drain valve removes a slight amount of water to reduce pressure (1/4 cup) to drain into the bucket. For testing, place a bucket at rear of pump under tube coming out of the machine in the back marked DRAIN. For permanent installation run a hose from the DRAIN outlet to a convenient sewer drain. • When us
ページ9に含まれる内容の要旨
8. Mist Line Assembly 8.1 TUBING CONNECTION • Use the supplied cutters to begin cutting the supplied high-pressure (black) tubing to the required lengths (see recommended lengths below). Be sure to measure the total length required for the mist line before cutting the tubing. Only cut what is needed. We suggest a straight line of 20 feet (6m) at first, because you can change the shape after testing the unit and the heads. • RECOMMENDED NOZZLE SEPARATION Mounting Height
ページ10に含まれる内容の要旨
recommended operating pressure range of 600-800 PSI (42-55 bar). If you reduce the number of nozzles, you will increase pressure. UNDER NO CIRCUMSTANCES SHOULD THE PRESSURE EXCEED 800 PSI (55 bar), as this can rupture lines and cause damage to seals and pump. This can be caused from not using enough nozzles. Extensive time would cause overheating. 8.4 Checking for Leaks • Check for leaks that may have occurred due to the tubing not being inserted beyond the o-ring seal. In case of
ページ11に含まれる内容の要旨
9. Maintenance procedures 9.1 SYSTEM PRESSURE • Your pump includes a 2000 PSI (138 bar) high pressure glycerine-filled gauge. Check the system pressure periodically during operation The operating pressure should be between 600-800 PSI (42–55 bar). DO NOT EXCEED 800 PSI (55 bar)! Note: an air bubble will be inside the pressure gauge. This is normal. 9.2 EXTERNAL WATER FILTER INSPECTION • Shut down water supply to pump before inspecting the filter element. • To insure the long
ページ12に含まれる内容の要旨
11 . Technical Data TM Jungle Mist Junior Anti-Drip 110VAC P/N 100072; 230VAC P/N 100074; 12VDC P/N 100068 Case Dimensions 12" x 10" x 13" (31 cm x 25 cm x 33 cm) GPM 0.25 Weight 20 lbs (9 kg) Shipping Container 28” x 14” x 15” (71 cm x 35.6 cm x 38 cm) Shipping Weight 36 lbs (16.4 kg) Motor HP 1/4hp Electrical Power 110VAC, 60 Hz, 2 amp (AC single-phase or DC) 230VAC, 50 Hz, 1 amp 12VDC, 14 amp Maximum Pressure 800 PSI (55 bar) Maximum Inlet 40 -
ページ13に含まれる内容の要旨
12. Limited Warranty Conditions TM Jungle Mist Junior Anti-Drip 1. Subject to the following conditions we will repair any defect or fault in the unit if it is caused by a proven factory fault and has been advised immediately after appearance and within 30 days of delivery to the end user. Insignificant deviations of the regular product quality does not guarantee replacement rights, nor do faults or defects caused by water, by generally abnormal environment conditions or Force M
ページ14に含まれる内容の要旨
If you should send the unit for service, do not forget to drain water from system. Obtain your RMA # by calling CITC. Payment arrangements for repair must be made before receiving RMA # in case unit is not covered under Limited Warranty. Send unit to: CITC RMA # XXXXXXX th 2100 196 Street SW Suite #138 Lynnwood, WA 98036 Tel: (888) 786-CITC or (425) 776-4950 Fax: (425) 776-5129 Website: www.citcfx.com E-mail: info@citcfx.com
