Desa VN2000BTAの取扱説明書

デバイスDesa VN2000BTAの取扱説明書

デバイス: Desa VN2000BTA
カテゴリ: 給湯器
メーカー: Desa
サイズ: 0.41 MB
追加した日付: 9/22/2014
ページ数: 36
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスDesa VN2000BTAの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Desa VN2000BTAに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Desa VN2000BTAをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Desa VN2000BTAのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Desa VN2000BTAの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Desa VN2000BTA 取扱説明書 - Online PDF
Advertisement
« Page 1 of 36 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Desa VN2000BTAを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Desa VN2000BTAの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

®
VENT-FREE NATURAL GAS HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
Models: VN2000BA, VN2000BTA, and VN2800BTA
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury, or loss of life.
— Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do n

ページ2に含まれる内容の要旨

SECTION PAGE CONTENTS Safety Information ......................................................................... 2 Product Identification .................................................................... 4 Local Codes ................................................................................... 4 Unpacking...................................................................................... 4 Product Features ............................................................................

ページ3に含まれる内容の要旨

SAFETY WARNINGS Continued WARNING ICON G 001 INFORMATION WARNING: Any change to this heater or its controls can be dangerous. Continued 1. Use only natural gas. Do not convert heater to use different fuel type. 2. If you smell gas • shut off gas supply • do not try to light any appliance • do not touch any electrical switch; do not use any phone in your building • immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions • if you cannot reach your gas su

ページ4に含まれる内容の要旨

Ignitor Button Control Knob PRODUCT IDENTIFICATION Grill Guard Glass Panel Front Panel Heater Cabinet Figure 1 - Vent-Free Natural Gas Heater (Model VN2800BTA Shown) Install and use heater with care. Follow all local codes. In the absence of local LOCAL CODES codes, use the latest edition of National Fuel Gas Code ANSI Z223.1, also known as NFPA 54*. *Available from: American National Standards Institute, Inc. 1430 Broadway New York, NY 10018 National Fire Protection Association, Inc. Batteryma

ページ5に含まれる内容の要旨

FRESH AIR WARNING WARNING ICON G 001 FOR This heater must have fresh air for proper operation. If not, poor fuel combustion could result. Read the following instructions to COMBUSTION insure proper fresh air for this and other fuel-burning appliances in your home. AND VENTILATION Today’s homes are built more energy efficient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to

ページ6に含まれる内容の要旨

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION FRESH AIR Determining if You Have a Confined or Unconfined Space FOR Use this worksheet to determine if you have a confined or unconfined space. COMBUSTION Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms. AND 1. Determine the volume of the space (length x width x height). VENTILATION Length x Width x Height = ___________________ cu. ft. (volume of sp

ページ7に含まれる内容の要旨

VENTILATION AIR FRESH AIR Ventilation Air From Inside Building FOR This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the COMBUSTION ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and AND 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). VENTILATION WARNING WARNING ICON G 001 Continued Rework wor

ページ8に含まれる内容の要旨

VENTILATION AIR (Continued) FRESH AIR Ventilation Air From Outdoors FOR Provide extra fresh air by using ventilation grills or ducts. You must provide two perma- nent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these COMBUSTION items directly to the outdoors or spaces open to the outdoors. These spaces include attics AND and crawl spaces. Follow the National Fuel Gas Code NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation for required size o

ページ9に含まれる内容の要旨

INSTALLING NOTICE TO WALL A qualified service person must install heater. Follow all local codes. CHECK GAS TYPE Use only natural gas. If your gas supply is not natural gas, do not install heater. Call dealer where you bought heater for proper type heater. INSTALLATION ITEMS Before installing heater, make sure you have the items listed below. • ground joint union • piping (check local codes) • sediment trap • sealant (resistant to propane gas) • test gauge connection * • tee joint • manual shuto

ページ10に含まれる内容の要旨

For convenience and efficiency, install heater INSTALLING • where there is easy access for operation, inspection, and service • in coldest part of room TO WALL An optional fan kit is available from your dealer. See Accessories, page 30. If Continued planning to use fan, locate heater near an electrical outlet. CEILING 36" Minimum 6" Minimum From Sides Of Heater Left Right Side Side 3" Minimum To Top Surface Of Carpeting, Tile Or Other FLOOR Combustible Material Figure 4 - Mounting Clearances As

ページ11に含まれる内容の要旨

INSTALLING HEATER TO WALL INSTALLING Mounting Bracket TO WALL The mounting bracket is located on back panel of heater. It has been taped there for Continued shipping. Remove mounting bracket from back panel. Mounting Bracket Figure 6 - Mounting Bracket Removing Front Panel Of Heater 1. Remove two screws near bottom corners of front panel. 2. Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4". 3. Pull bottom of front panel forward, then down. 4. Remove cardboard

ページ12に含まれる内容の要旨

Marking Screw Locations INSTALLING 1. Tape mounting bracket to wall where heater will be located. Make sure mount- ing bracket is level. TO WALL Continued WARNING WARNING ICON G 001 Maintain minimum clearances shown in Figure 8. If you can, provide greater clearances from floor and joining wall. 2. Mark screw locations on wall (see Figure 8). Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only. 3. Remove tape and mounting bracket from wall.

ページ13に含まれる内容の要旨

4. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to INSTALLING “pop” open anchor wings. IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings. TO WALL Continued Figure 10 - Popping Open Anchor Wings For Thin Walls 5. Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors. 6. Insert mounting screws through bracket and into wall anchors. 7. Tighten screws until mounting bracket is f

ページ14に含まれる内容の要旨

CONNECTING NOTICE A qualified service person must connect heater to gas supply. TO GAS Follow all local codes. SUPPLY WARNING WARNING ICON G 001 Never connect heater to private (non-utility) gas well. This gas is commonly known as well-head gas. IMPORTANT: Check gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 14 inches of water. If gas line pressure is higher, heater regulator damage could occur. CAUTION WARNING ICON G 001 Use only new, black i

ページ15に含まれる内容の要旨

IMPORTANT: Hold pressure regulator with wrench when connecting it to gas piping CONNECTING and/or fittings. Note: Burner bracket TO GAS not shown for clarity Pressure SUPPLY Regulator Continued 1/2" NPT Pipe Nipple Heater Ground Joint Cabinet Union Tee Joint Manual Shutoff Test Reducer Bushing to Valve * Gauge 1/8" NPT Connection * 1/8" NPT From Gas Meter Plug Tap (4" W.C. to 10.5" W.C. Pressure) Tee Joint Sediment Pipe Nipple 3" Minimum Trap Cap Figure 13 - Gas Connection * An A.G.A. design c

ページ16に含まれる内容の要旨

4. Check all joints of gas supply piping system. Apply mixture of liquid soap and CHECKING water to gas joints. Bubbles forming show a leak. 5. Correct all leaks at once. GAS CONNECTIONS Test Pressures Equal To or Less Than 1/2 PSIG 1. Close manual shutoff valve (see Figure 14). Continued 2. Pressurize supply piping system by either using compressed air or opening main gas valve located on or near gas meter. 3. Check all joints from gas meter to manual shutoff valve (see Figure 15). Apply mixtur

ページ17に含まれる内容の要旨

OFF HI OPERATING FOR YOUR SAFETY READ BEFORE LIGHTING HEATER WARNING WARNING ICON G 001 Models VN2000BTA If you do not follow these instructions exactly, a fire or and VN2800BTA explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is he

ページ18に含まれる内容の要旨

4. Wait five (5) minutes to clear out any gas. Then smell for gas, including OPERATING near the floor. If you smell gas, STOP! Follow “B” in the safety information HEATER at the top of page 17. If you don’t smell gas, go to the next step. Models VN2000BTA C-clockwise 5. Turn control knob counterclockwise to the PILOT position. Press and VN2800BTA in control knob for five (5) seconds (see Figure 16). Continued Note: You may be running this heater for the first time after hooking up to gas supply

ページ19に含まれる内容の要旨

OPERATING TO TURN OFF GAS TO APPLIANCE HEATER Shutting Off Heater Models VN2000BTA 1. Turn control knob clockwise to the OFF position. Clockwise and VN2800BTA 2. Turn off all electric power to the appliance if service is to be performed. Continued Shutting Off Burner Only (pilot stays lit) 1. Turn control knob clockwise to the PILOT position. Clockwise THERMOSTAT CONTROL OPERATION (Models VN2000BTA and VN2800BTA Only) The thermostatic control used on these models differs from standard thermo-

ページ20に含まれる内容の要旨

OPERATING FOR YOUR SAFETY READ BEFORE LIGHTING HEATER WARNING WARNING ICON G 001 Model VN2000BA If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Desa 15 取扱説明書 給湯器 0
2 Desa 6000 BTU/HR 取扱説明書 給湯器 2
3 Desa and CVDR30 取扱説明書 給湯器 0
4 Desa B 取扱説明書 給湯器 0
5 Desa A, C, B 取扱説明書 給湯器 0
6 Desa CBT30NT, CBT30PT 取扱説明書 給湯器 0
7 Desa CBN20T 取扱説明書 給湯器 0
8 Desa CCL3018NTA 取扱説明書 給湯器 0
9 Desa CCL3018NA 取扱説明書 給湯器 0
10 Desa CCL3018PTA 取扱説明書 給湯器 0
11 Desa CCL3018PTA/NTA, CCL3924PTA/NTA, CCL3930PTB/NTB 取扱説明書 給湯器 0
12 Desa CCL3924NA 取扱説明書 給湯器 0
13 Desa CCL3924NTA 取扱説明書 給湯器 0
14 Desa CCL3930NTB 取扱説明書 給湯器 0
15 Desa CDR3924NT 取扱説明書 給湯器 0
16 A.O. Smith 000 取扱説明書 給湯器 8
17 A.O. Smith 101 取扱説明書 給湯器 3
18 A.O. Smith 12 40GPC T 100 取扱説明書 給湯器 4
19 A.O. Smith 104 Series 取扱説明書 給湯器 3
20 A.O. Smith 104 - 110 取扱説明書 給湯器 6